Suhr Eclipse User manual

User Guide

2
Table of Contents
Overview � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3
Getting Connected � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4
Channel Selection / Bypass � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5
Controls � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6
Battery Monitor � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 7
FX Link (External Control)� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8
Sample Settings � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 9
Technical Specifications � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 10
Warranty � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 10

3
Overview
The Suhr Eclipse is a versatile, no compromise, dual channel overdrive/dis-
tortion that delivers a wealth of warm, organic amp-like tones in an easy to
use, compact form factor�
Eclipse’s incredible versatility stems from its powerful and intuitive two
channel circuit design� Each channel features its own Gain, Level and
3-Band passive EQ similar to a channel switching amplifier� Both channels
can be voiced independently to accommodate all of your playing needs�
The blue and red channel in the Eclipse sound identical, and the beauty of
this lies in the individual passive EQ circuits� You can set one channel for a
tight, scooped rhythm sound and the other to a more saturated, midrange
focused tone for solos�
Our goal with the passive EQ circuit in the Eclipse is to make it as amp-like
and natural as possible� Eclipse is equally comfortable in low gain overdriv-
en tones as it is in tight, high gain aggressive tones�
Sometimes you may need to plug into a really dark, or bright amplifier� The
unique Voice control allows you to fine tune the top end response to match
the amplifier that you are playing through�
Eclipse offers features not seen in most overdrive/distortion pedals� With the
ability to control its channels and bypass with an external effects switching
system via FX LINK, and the ability to start up automatically in a desired
channel on power up, Eclipse is incredibly rig friendly�
Thank you for purchasing the Suhr Eclipse Dual Overdrive/Distortion™
Pedal.
Please take the time to read this manual to get the most out of the Eclipse.
The more you familiarize yourself with the features of this pedal, the more
you will enjoy its benets and maximize its potential.

4
Getting Connected
Input: Plug the cable from your guitar into here, or from the previous
effect’s output�
DC Input: Eclipse accepts power from power supplies in the range of 9
to 18 Vdc (center negative) See Technical Specifications on pg 10.
Eclipse can also be powered internally from a 9V battery as described
below�
Output: Plug a cable from here to an amp or another effect’s input�
Installing/Replacing The Battery:
1�Unscrew the backplate of the pedal to access the battery compartment
with the battery snap located inside�
2�Plug in a 9V battery to the snap and re-screw the backplate�
NOTES:
The battery is connected when a cable is plugged into the Input jack
and there is no cable plugged into the DC input.
Remember to unplug your cable from the input jack when you are done
playing to disconnect the battery in order to insure a long battery life.
This step is not needed if a cable is plugged into the DC input.
TIP: For longer battery life, an Alkaline battery is recommended.

5
Channel Selection / Bypass
Eclipse has two channels (blue and red) with independent settings that are
selected by the switch below the desired channel� The channels can be set
for the same sound on each channel, or they can be radically different�
The left side is Channel 1 and contains a blue LED above its dedicated
footswitch�
The right side is Channel 2 and contains a red LED above its dedicated
footswitch�
Channel Selection and Bypass functions:
• Stepping on the left switch will turn Channel 1 on or off�
• Stepping on the right switch will turn Channel 2 on or off�
• Switching from one channel to another will automatically turn off the previ-
ous channel�
• When no channel is selected, Eclipse is in True Bypass (INPUT jack is con-
nected directly to OUTPUT jack via Relay)

6
Controls
Gain: Adjusts the amount of gain added to your tone, taking you from tube-
like classic crunch and overdriven tones to high gain/distortion territory�
Level: Adjusts the output volume of the pedal� Eclipse provides enough vol-
ume to push the front end of any tube amp into natural overdrive�
B (Bass): The bass knob is a shelving filter that reduces (counter clockwise)
or boosts (clockwise) the amount of bass frequencies of the respective chan-
nel�
M (Middle): The mid knob reduces (counter clockwise) or boosts (clockwise)
the amount of mid frequencies of the respective channel�
T (Treble): The treble control is a shelving filter that reduces (counter clock-
wise) or boosts (clockwise) the amount of treble frequencies of the respective
channel�
Voice (global): The voice control allows you to tailor the overall brightness
of the pedal to be pleasing for your specific amplifier� We suggest this knob
be dialed in as preferred first, while the 3-band EQ knobs (B, M, T) are flat
(set to the middle)� Moving the knob counterclockwise reduces the amount of
high-frequencies, while rotating clockwise increases the amount of high-fre-
quencies for both channels�
Tip: This control is useful for amps with bright switches. When the clean chan-
nel of your amp has the bright switch on, dial the voice knob counterclockwise
to maintain a pleasant overdriven/distortion tone.

7
Battery Monitor
3-Position Slide Switch
The internal 9V battery is monitored at both power up and during use� The
user will be alerted when the battery voltage becomes low� When the battery
becomes too low to reliably operate the pedal, True Bypass is activated�
Upon powering up the pedal, the battery voltage is measured� If the voltage
is at a low voltage (4�5V), the LEDs will flash 3 times to alert the user� Normal
operation will then resume� Should the battery fail completely (<4V), Eclipse
will switch to true bypass mode and the LEDs will begin to flash� This will en-
sure that the signal continues uninterrupted and undistorted�
At the top of the pedal between the Input and Output jack is a 3 position tog-
gle switch�
• When pushed towards Channel 1, the pedal powers on with Channel 1
activated�
• When pushed towards Channel 2, the pedal powers on with Channel 2
activated�
• When set to FL (center), the pedal will accept external control via the FX
LINK jack, and will also power on with neither channel activated�

8
FX Link (External Control)
Eclipse contains an 1/8” stereo TRS input jack called FX LINK that allows
the pedal to be controlled by an effects switching system with TRS control
output jacks, such as the BOSS ES-8 or ES-5�
Connect a TRS 1/8” cable into the FX LINK jack from your effects
switching system� A 1/4” to 1/8” stereo cable would typically be used.
Set the 3-position slide switch to the center (FL) on startup for external
control
A connection between the Tip and Sleeve controls Channel 2’s ON/OFF
state�
• When Tip is connected to Sleeve, Channel 2 is ON
• When Tip is disconnected from Sleeve, Channel 2 is OFF
A connection between the Ring and Sleeve controls Channel 1’s ON/OFF
state�
• When Ring is connected to Sleeve, Channel 1 is ON
• When Ring is disconnected from Sleeve, Channel 1 is OFF
Tip (Channel 2) has priority over Ring (Channel 1) when both are connected
at the same time.
Setup

9
Sample Settings
Classic Crunch (Rhythm CH1, Lead CH2) Hard Rock (Rhythm CH1, Lead CH2)
With these sample settings, dial in the Voice knob to suit your amplifier�
Metal (Rhythm CH1, Lead CH2) Boost (Front End Boost CH1, Front End Mid Boost CH2)

10
Technical Specications Warranty
Input Impedance: 1M Ohm
Output Impedance: 100 Ohm
Power Connector: 9Vdc, center negative, 2.1mm x 5.5mm
Operating voltage: 4V to 18V (nominal 9V)
Maximum Voltage: 20Vdc
Reverse Battery Protection: Yes
Over Voltage Protection: Yes
Current Consumption: 12mA min, 15.5mA max
Estimated Battery Life: 25 - 32 hours continuous use
Dimensions: 4.875”(W) x 3.875”(D) x 1.375”(H)
Weight: 1.13lb
FX Link Connector: ⅛” TRS jack
FX Link Max Voltage: 3.3Vdc
Shield -> Tip: Activate Channel 2 (Red LED)
Shield -> Ring: Activate Channel 1 (Blue LED)
ROHS Compliant: Yes
JS Technologies, Inc� (JST) warrants for lifetime from date of purchase by the
initial retail purchaser that this product shall be free from defects in workman-
ship� Electronic components such as capacitors, resistors, filters, transformers,
jacks, and pots are covered for 5 years� Any parts determined defective by JST
within the five (5) year term shall be repaired or replaced by JST without charge
for parts and labor provided the unit is returned, transportation costs prepaid, to
JS Technologies, Inc�, 601 Crane Street, Unit A, Lake Elsinore, CA 92530, or to
such facility authorized by JST� JST will pay shipping costs to return the unit to
its owner� Defects in workmanship will be determined by JST for limited lifetime
coverage�
This warranty does not cover damage caused by accident, misuse, abuse, ne-
glect, unauthorized or improperly performed repairs, alterations, and/or wear
and tear occasioned by use of the product, and does not include any expense
for inconvenience or loss of use while the product is being repaired or replaced�
JST expressly disclaims any liability for consequential damages arising from the
sale, use, or inability to use the product� Any warranty implied by law, includ-
ing any warranty of merchantability or fitness, is expressly limited to the one (5)
year warranty term for the parts on our amplifiers and electronic products� The
foregoing statements of warranty are exclusive and in lieu of all other remedies�
Workmanship lifetime warranty is limited strictly to the original retailer purchaser
of the instrument registered with JST within 10 days of purchase from an autho-
rized JST dealer or distributor� JST will pay shipping costs to return the unit to its
owner within the mainland U�S�
The above warranty policy only applies to customers in USA� If you are an in-
ternational customer, please check with your distributor and the dealer in your
country for warranty matters� Warranty issues must be handled through your
dealer or distributor� If you are an international customer who purchased (or
plan to purchase) from a US dealer, we can handle warranty matters direct but
you will be responsible for shipping both ways� We encourage international cus-
tomers to purchase through your local distributor or dealer for this reason� Our
international distributors are set up to handle warranty issues in their respective
countries� If you do not have an authorized Suhr dealer in your country, please
contact us direct for further details�

NOTE: This product has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This
product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instruction
manual, may cause harmful interference with radio communications. Operation of this product in a residential area is likely to cause harmful
interference, in which case you will be required to correct the interference at your own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful
interference. 2) This device must accept any interference received, including interference that may cause undesired operation.
Notice: The FCC regulations provide that changes or modifications not expressly approved by J.S. Technologies Inc. could void your authority to
operate this equipment.
These limits are designed to provide reasonable protection against harmful interference in a non-residential installation. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference with radio or television
reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the antenna of the radio/television receiver.
• Increase the separation between this equipment and the radio/television receiver.
• Plug the equipment into a different outlet so that the equipment and the radio/television receiver are on different power mains branch circuits.
• Consult a representative of J.S. Technologies Inc. or an experienced radio/television technician for additional suggestions.
Table of contents
Other Suhr Music Pedal manuals