Topaz F-ARL/150/40K/S3/480 User manual

INSTALLATION INSTRUCTIONS FOR LED AREA LIGHT
Tools Required:
Allen Hexagon Wrenches, Wire Strippers, Wire Cutters, Screwdriver
F-ARL/150/50K/P3
F-ARL/150/50K/P3/M
F-ARL/150/50K/P5
F-ARL/150/50K/S3
F-ARL/150/50K/S3/480
F-ARL/300/50K/P3
F-ARL/300/50K/P3/M
F-ARL/300/50K/P5
F-ARL/300/50K/S3
F-ARL/300/50K/S3/480
With 120V through 277V or 480VAC, 50/60 Hz and connected
F-ARL/150/40K/S3
F-ARL/150/40K/S3/480
F-ARL/300/40K/S3
F-ARL/300/40K/S3/480

Instructions:
Wiring Diagram:
Optional Brackets and Installation Instructions:
There are 4 optional brackets for this fixture. The following is shoebox fixtures with different
brackets
Black/Brown:ACL
White/Blue:ACN
Green/Yellow Dim+(Purple)
Dim-(Gray)
TYPE A
TYPE B
TYPE C
TYPE D
INSTALLATION INSTRUCTIONS FOR LED AREA LIGHT
This product is equipped with standard 1-10V dimming
Slipfitter
Pole Mount
Yoke Mount
Universal Slipfitter/
Pole Mount

Installation Instructions with different brackets:
1. ADJUSTABLE FITTER MOUNTING (TYPE A)
Step 1: Remove the bracket mounting screws on the fixture and run the wires through the
bracket. (Figure 1)
Step 2: Install the bracket on the fixture. (Figure 2)
2. POLE MOUNTING (TYPE B)
Step 1: Remove the bracket mounting screws on the fixture,open the side lid of bracket and run
the wires through the bracket. (Figure 3)
Step 2: the side lid and tighten it . (Figure 4)Install the bracket on the fixture, then cover
3. YOKE MOUNTING (TYPE C)
Step 1: Remove the bracket mounting screws on the fixture and run the wires through the
bracket. (Figure 5)
Step 2: Install the bracket on the fixture. (Figure 6)
Figure 1 Figure 2
Figure 3 Figure 4
Figure 5 Figure 6
INSTALLATION INSTRUCTIONS FOR LED AREA LIGHT

Installation of LED Luminaire
1. ADJUSTABLE FITTER MOUNTING (TYPE A)
Step 1: Loosen the four bolts on AM bracket, connect the wires correctly, and pull the wires into
the poles.(Figure 9)
Step 2: .(Figure 10)Place the bracket into the pole and lock the four bolts
Notice: Adjustable angle is 0-90°(Figure 9)
90°
Support
Wire
Locking Bolt
Adjusting Bolt
Luminaire
Figure 9
Support
AM Bracket
AM Bracket
Figure 10
4. (TYPE D)UNIVERS & POLE MOUNTINGAL LIPFITTERS
Step 1: Remove the bracket mounting screws on the fixture,open the side lid of bracket and run
the wires through the bracket. (Figure 7)
Step 2: . (Figure8)Install the bracket on the fixture, then cover the side lid and tighten it
Figure 7 Figure 8
INSTALLATION INSTRUCTIONS FOR LED AREA LIGHT
Luminaire

3. YOKE MOUNTING (TYPE C)
Step 1: Drill holes on the wall as shown. (Figure 14)
Step 2: Knock the expansion bolts into the wall.(Figure 15)
Step 3: Connect the fixture to the bracket and tighten the screws; connect the wires properly and
put them into junction box.(Figure 16)
Notice: Adjustable angle is 0-90°(Figure 16)
77
Figure 14 Figure 15 Figure 16
Expansion Bolt
10
90°
Adjusting Bolt
YM Bracket
2. POLE MOUNTING (TYPE B)
Figure 12 Figure 13
Round Pole Installation Solution: Put Square
Thin Silicone Pad only, remove Cambered
Thick Silicone Pad(Figure 13)
Square Pole Installation Solution: Put both
Cambered Thick Silicone Pad and Square
Thin Silicone Pad(Figure 12)
Square Pole
1
2
(100*100mm
/above)
DM Bracket
1
Round Pole
(Ø127mm)
DM Bracket
Cambered Thick Silicone Pad
2
Bolt Luminaire
DM Bracket
Side Lid
Adjusting Bolt
1
2
1Square Thin Silicone Pad
Figure 11
INSTALLATION INSTRUCTIONS FOR LED AREA LIGHT
Luminaire Luminaire
Luminaire

4. &ADJUSTABLE FITTER MOUNTING POLE MOUNTING (TYPE D)
4.1 ADJUSTABLE FITTER MOUNTING
Step 1: . (Figure 17)Remove the spare parts from A&D bracket
Step 2: Loosen the four bolts on A&D bracket, connect the wires correctly, and pull the wires into
the poles.(Figure 18)
Step 3: . (Figure 18)Place the bracket into the pole and lock the four bolts
Notice: Adjustable angle is 0-90°(Figure 18)
4.2 POLE MOUNTING
Step 1: Remove the four bolts from A&D bracket, remove the four rubber plugs from installation
bar, put the four rubber plugs on the place where the fours bolts were previously placed
on the bracket for waterproof purpose(Figure 19)
Step 2: Fix A&D bracket to square pole with bolt, open the cover of A&D bracket junction box, pull
the wire into bracket junction box, connect the wire properly and cover the junction box.
(Figure 20)
Notice: .(Figure 20)Adjustable angle is 0-90°
Same as round pole installation, please remember to use the adapting plate for round pole
installation( Figure 21)
Figure 19
Figure 17 Figure 18
Figure 20 Figure 21
90°
Support
Locking bolt
Adjusting bolt
Wire
Adapting Plate
A&D Bracket
Round Pole
Installation bar
Rubber plug
Fixing Bolt
Square Pole
Cap
90°
Adjusting bolt
A&D Bracket
A&D Bracket
Locking bolt
Spare Part
Junction Box
INSTALLATION INSTRUCTIONS FOR LED AREA LIGHT
Luminaire
Luminaire
Luminaire

Work light
(Green LED on)
Daylight senson
Antenna module
100~277V input
100~277V output control
Sync
1~10V
+
-
Detection area
Hold-time
Standby period
Daylight threshold
Stand-by dimming level
Screws
Cover
Sensor
Instructions for Motion sensor (Figure 24)
Open the cover above motion sensor by loosen the screws；
Set the motion sensor through DIP switches as per actual requirements；
Lock the cover above the motion sensor through screws.
Structure of motion sensor
Photocell
Shorting cap
Socket
Figure 23 Figure 24
1234567812 3 4 5 6
OUT P UT INPUT
L N L N
SYNC
+
-
1-10V
0.75-1.5
When the photocell function is requird,photocell should be installed on the back of luminaire;
When it’s not required,shorting cap should be installed on the back of luminaire.
Instructions for Photocell (Figure 23)
INSTALLATION INSTRUCTIONS FOR LED AREA LIGHT
Luminaire
Luminaire

Detection area
Detection area can be reduced by selecting the combination on the
DIP switches to fit precisely each application.
Factory setting：Ⅰ
Hold time
Refers to the time period the lamp remains at 100%
illumination after no motion detected.
Factory setting：Ⅰ
Stand-by period
Refers to the time period the lamp remains at a low
light level before it completely switches off in the
long absence of people.
When set to“ ”mode, the low light is maintained until
motion is detected.
Factory setting：Ⅰ
Daylight sensor
The sensor can be set to only allow the lamp to illuminate below a defined
ambient brightness threshold.
When set to Disable mode, the daylight sensor will switch on the lamp when
motion is detected regardless of ambient light level.
50lux, 30lux: twilight operation, 10lux, 5lux: darkness operation only.
Note that daylight sensor is active only when lamp
totally switches off.
Factory setting：Ⅶ
Stand-by dimming level
The low light level you would like to have after the
hold time in the long absence of people.
Factory setting：Ⅰ
Function of DIP switches：
Ⅴ
Ⅵ
34 5
ON ON ON
ON ON
ON ON
ON
ON ON
-
-
--
-
---
5s
30s
90s
3min
20min
30min
ON
Ⅰ
Ⅱ
Ⅲ
Ⅳ
Ⅴ
Ⅵ
67 8
ON ON ON
ON ON
ON ON
ON
ON ON
-
-
- -
-
---
0s
5s
10min
30min
ON
Ⅰ
Ⅱ
Ⅲ
Ⅳ
Ⅶ
5min
1h
+∞
-
ON
-
5 6
Ⅰ
Ⅱ
Ⅲ
Ⅳ
ON ON 50%
ON
ON
-
30%
-
ON 20%
- -
10%
Ⅴ
Ⅵ
12 3
ON ON ON
ON ON
ON ON
ON
ON ON
-
-
- -
-
---
2Lux
ON
Ⅰ
Ⅱ
Ⅲ
Ⅳ
ⅦDisable
-
ON
-
4
ON
ON
ON
ON
-
-
-
5Lux
10Lux
25Lux
50Lux
100Lux
1 2
Ⅰ
Ⅱ
Ⅲ
Ⅳ
ON ON 100%
ON
ON
-
75%
-
ON 50%
- -
10%
INSTALLATION INSTRUCTIONS FOR LED AREA LIGHT