Topfield TF 5810 PVRt User manual

TOPFIELD
TF 5810 PVRt
User Guide
Digital Terrestrial Receiver
Personal Video Recorder

Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
• Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
• The mains plug, which is used as a disconnect device,
shall remain readily operable.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to a person.
The exclamation point, within an equilateral triangle, is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the product.

iv CONTENTS
Contents
Contents iv
1 Introduction and getting started 1
1.1 Unpacking .............................. 2
1.2 Remote control buttons and their functions ........... 3
1.3 Rear panel connections ....................... 6
1.4 Connecting up your PVR ..................... 8
1.4.1 Connecting the aerial to your PVR ............ 9
1.4.2 Connecting the PVR to your TV using a HDMI . . . . 10
1.4.3 Connecting the PVR to your TV using a SCART . . . . 10
1.4.4 Connecting to your HiFi system ............. 10
1.5 Switching on for the first time ................... 11
1.5.1 Searching for TV and radio channels .......... 11
1.5.2 Basic system settings .................... 12
1.5.3 Time and date options ................... 12
1.5.4 AV output settings ..................... 13
1.6 Pay TV ................................ 16
2 Watching TV 18
2.1 Starting to watch television .................... 19
2.1.1 Volume control ....................... 20
2.1.2 Changing channels ..................... 20
2.1.3 Radio channels ....................... 21
2.2 Electronic Programme Guide ................... 21
2.3 Time Shift television ........................ 24

CONTENTS v
2.3.1 Rewinding TV ....................... 24
2.3.2 Pausing TV ......................... 26
3 Recording and playing TV programmes 27
3.1 How your PVR records ....................... 27
3.2 Instant recording .......................... 29
3.3 Scheduled recordings ........................ 31
3.3.1 Scheduling a recording using the EPG .......... 31
3.3.2 Altering the details ..................... 33
3.3.3 Viewing your recording schedule ............ 35
3.3.4 Scheduling a recording without using the EPG . . . . 37
3.4 Things you should know about recording on your PVR . . . . 38
3.4.1 Dual recordings ...................... 38
3.4.2 Watching television while dual recording ........ 39
3.4.3 When recordings start or stop .............. 39
3.4.4 Leaving the PVR in standby ............... 40
3.4.5 Switching off while recording .............. 40
3.4.6 How recordings are named ................ 41
3.5 Playing back recordings ...................... 41
3.5.1 Playback features ...................... 42
3.5.2 Bookmarks and resume play ............... 43
3.5.3 After you’ve watched a recording ............ 44
4 Extra features 46
4.1 Make the most of digital TV .................... 46
4.1.1 Subtitles ........................... 47
4.1.2 Sound tracks ........................ 47
4.1.3 Picture in Picture ...................... 48
4.1.4 Digital teletext ....................... 49
4.1.5 Sleep timer ......................... 50
4.2 Adjusting the on-screen display .................. 51
4.3 Organizing channels ........................ 51
4.3.1 Favourite channels ..................... 52
4.3.2 Setting up favourite channels ............... 52
4.3.3 Managing lists of favourites ............... 53
4.3.4 Watching TV using favourites .............. 54

vi CONTENTS
4.4 Organising recordings ....................... 55
4.4.1 Renaming recordings ................... 56
4.4.2 Organising recordings ................... 56
4.4.3 Copying recordings .................... 57
4.4.4 Editing recordings ..................... 58
4.5 Additional playback and viewing features ........... 59
4.5.1 Playing back multiple recordings ............ 60
4.5.2 Slow motion playback ................... 60
4.5.3 Repeat playback ...................... 60
4.5.4 Parental lock ........................ 61
4.5.5 Restricting access to recorded programmes ....... 62
4.5.6 Restricting access to TV channels ............ 62
4.5.7 Organising the channel list ................ 63
5 The PC Connection 64
5.1 Installing the software and drivers ................ 65
5.2 Connecting the PVR to your PC .................. 65
5.2.1 Using Altair ......................... 66
5.2.2 How files are organised on your PVR .......... 68
5.2.3 Transferring files ...................... 68
6 Advanced features 70
6.1 MP3 playback ............................ 70
6.2 Formatting the hard disk ...................... 71
6.3 Firmware updates ......................... 72
6.3.1 Installing a firmware update via USB .......... 72
6.3.2 Installing a firmware update via a serial connection . . 74
6.3.3 Installing a firmware update over the air ........ 74
6.4 Copy Firmware and Settings to Another System ........ 75
6.4.1 Copy Firmware to Another System ........... 75
6.4.2 Copy Settings to Another System ............ 76
6.5 TAPs - Additional software for your PVR ............ 77
6.5.1 Installing TAPs ....................... 77
6.5.2 Starting TAPs ........................ 78
6.5.3 Starting TAPs automatically ............... 79
6.5.4 Troubleshooting TAPs ................... 79

CONTENTS vii
7 Troubleshooting and How to 81
7.1 Troubleshooting ........................... 81
7.1.1 Unexpected channel changes ............... 81
7.1.2 Failed recordings ...................... 82
7.1.3 PVR crashes ......................... 82
7.1.4 Incorrect channel numbers and duplicate channels . . 83
7.1.5 Unable to view Pay TV channels ............. 84
7.2 How to ................................ 85
7.2.1 Adding a new channel ................... 85
7.2.2 Moving home ........................ 86
7.3 Contacting support ......................... 86
A Technical Information 87
Index 89

1
Chapter 1
Introduction and getting
started
Congratulations on buying a Topfield TF 5810 Personal Video
Recorder terrestrial(PVRt). The TF 5810 PVRt allows you to
view and record digital TV channels easily, via an ordinary
television aerial. You can receive all the Freeview channels
broadcast in your area, which includes a range of digital radio
stations too. In addition, with a small subscription module, you
can access some additional channels from pay TV broadcasters.
Your new PVR allows you to record two different programmes
simultaneously, and even to play back existing recordings
while you’re making new ones. With it’s large hard drive,
there’s plenty of space for all the shows you want to watch,
and the built in electronic programme guide (EPG) makes it
easy to find programmes and schedule automatic recordings.
As well as recording and playback of TV programmes, it has
plenty of other features. You can pause TV when the phone
rings, for example, or rewind a sports match to watch someone
score a second time. Channels can be arranged into groups
of ‘favourites,’ and there are other useful features like picture

2 Introduction and getting started
in picture, interactive services and even a link to your home
computer.
We’ll cover all of those issues in this manual, starting from
basic installation and setup, then looking at everyday use, and
finally giving you an idea of some of the advanced features
that you can make use of when you’re comfortable with how
your PVR works.
1.1 Unpacking
Before going any further, check that you have received the
following items with your PVR.
• Remote control unit
• Two AAA batteries for the remote control
• One aerial cable, to link the PVR to your TV aerial
• One loop cable (a short aerial cable)
• One SCART cable, to link the PVR to your television set
• A copy of this user guide
These items may vary according to your local area.
Unpack the cables, and insert the batteries in the remote control;
make sure you insert them the correct way round, following
the symbols on the inside of the battery compartment.
Before going any further, you should familiarise yourself with
the remote control and with the connectors on the rear of the
PVR. Let’s look at the remote control first. Dont worry if some
of the things we mention here seem a little unusual — all the
functions and features will be explained later on.

1.2 Remote control buttons and their functions 3
1.2 Remote control buttons and their functions
3
12
5
6
20
15
17
16
9
22
25
26
29
30
34
33
4
7
8
14
17
18
19
23
24
27
28
31
32
21
16
35
36 37
10 13
11
12
1
 Use this button to switch the
PVR in and out of standby mode.
2
 Press this button to temporarily
switch off the sound; press again
to switch it back on.
3
 This button changes a video res-
olution.
4
 Press this button to change a
aspect ratio.
5
 This button switches the output
of the main SCART socket between
the PVR’s picture and the device
connected to the secondary SCART
socket.
6
Switch the PVR between televi-
sion and radio channels.
7
 These Numeric buttons are used to
enter channel numbers and menu
options.
8
 This button switches between
the current channel and the previ-
ously viewed one.
9
 Press this button to display
more information about the cur-
rent programme or a programme
highlighted in the EPG.
10
 Press this button to select an audio track and a sound
mode.

4 Introduction and getting started
11
Press this button to select a teletext track.
12
Press this button to select a subtitle track.
13
 This button gives access to additional features, such
as subtitles, favourites, soundtracks, teletexttracks and
the sleep timer.
14
 Use this button to access the PVR’s menus, or to
return to the previous menu from a sub-menu.
15
 This button displays the Electronic Programme Guide
(EPG).
16
 In system menus, the up and down buttons allows you
to choose an item from the menu. They are also used to
navigate through the electronic programme guide, and
in interactive services.
17
 In system menus, the left and right buttons allow you to
change the options for a menu item. They are also used
to navigate through the electronic programme guide, and
in interactive services.
18
 This button is used to select items in menus, and in
interactive services. When viewing live TV, it displays
the channel list.
19
Press Exit to leave the current screen.
20
 Press List once to display a list of all the channels
stored for TV or Radio. Press it again when the list is
displayed to select a group of Favourite channels.
21
 The and buttons increase and decrease the vol-
ume. In some screens, they also work as right and left
movement keys.
22
 The and buttons move to the next or previous
channel in the channel list or the current Favourites list.
In some screens, they also work as up and down move-
ment keys.

1.2 Remote control buttons and their functions 5
23
 Press to reverse playback; press again to increase
speed, or hold down to move along the progress bar.
24
 Press to pause playback of a recorded programme or
live television.
25
 Press to go to normal playback speed, or to display
the progress bar for faster navigation when playback has
already started.
26
 Press to start fast forward, and again to increase play-
back speed, or hold down to move along the progress
bar.
27
Press to start a recording.
28
 Press to stop playback, to stop a recording, or to jump
back to live TV from time shifted television.
29
 This button starts slow motion playback. Subsequent
presses change the speed of playback.
30
 This button displays the list of recorded programmes
that have been saved on your PVR’s hard disk.
31
 When the PiP function is being used, this key displays
a list so that you can choose which channel is displayed in
the smaller picture. When the Progress Bar is displayed,
it allows you to select a section of a programme for repeat
playback or editing.
32
 This button changes the position of sub-picture coun-
terclockwise. It is also used to jump back to beginnng of
recording during a playback.
33
 This button changes the position of sub-picture clock-
wise. It is also used to jump to end of recording during a
playback.
34
 This button swaps the Picture in Picture with the
main picture.

6 Introduction and getting started
35
 These coloured buttons have a different function per
menu. They will be guided by on-screen help.
36
 Press this button once to start the Picture in Picture
(PiP) function. Press again to change the position of the
Picture in Picture, and to turn it off.
37
This button displays the favourite lists.
The coloured buttons on the remote control are used by inter-
active services, such as BBCi or Teletext — for example, you
may see a message on screen asking you to ‘Press Red.’ The
keys are also used in some of the PVR menus, where you will
usually see an on screen message telling you which key to use
for which function.
1.3 Rear panel connections
The TF 5810 PVRt has a wide range of connections on the back
panel, and it can look a little complicated at first. Dont worry —
it’s much simpler than it looks, and not everyone needs to use
all the connections. We’ll explain some of the most common
ways of connecting the PVR after we’ve looked at the rear
panel.
ANT 1 IN
RF LOOP
1 OUT
RF LOOP
2 OUT AUDIO
L
R
S-VIDEO VCR USB S/PDIF RS-232
VIDEO
TV
ANT 2 IN
1 3 5 9
2 4 6 11 12 1310
8
HDMI
7
1
ANT 1 IN This is the input to one of the TV tuners in your
PVR (it has two, so that it can record two things at the
same time.) This socket should be connected to your
TV aerial.

1.3 Rear panel connections 7
2
RF LOOP 1 OUT This is the output from the first tuner.
Normally, you should use the supplied loop cable to
connect this to the ANT 2 IN connector.
3
ANT 2 IN ANT 2 is the input to the second of the tuners
in your PVR.
4
RF LOOP 2 OUT This is the output from the second
tuner.
5
Video output This yellow socket carries composite video.
This format is used by some video projectors, and
audio visual amplifiers; most users will not need to
use this socket.
6
Audio outputs These two connectors provide left (white)
and right (red) channel audio outputs, which can be
connected to a hi-fi system, if you wish.
7
HDMI This socket carries high definitioin video with dig-
ital audio.
8
S-Video The S-Video output is another way of connect-
ing some televisions, projectors or AV amplifiers to
your PVR. Again, most users will not need to use this
socket.
9
TV SCART This is the main output socket from your
PVR, carrying both audio and video connections us-
ing the large SCART connectors. You should normally
use the supplied SCART cable to connect this to the
corresponding socket on your television set.
10
VCR SCART This is a secondary SCART socket. It is in-
tended to be used to allow other devices to record the
material you are watching or playing on your PVR,
and can also pass their signal through to your televi-
sion, so that even if you have only one SCART con-
nector on your TV you can use, for example, both the
PVR and a DVD player, selecting one or the other via
the SAT button on the remote control.

8 Introduction and getting started
11
USB port By connecting to your computer using this USB
port, you can upgrade the built-in software of the PVR,
transfer recorded programmes to your computer, or
transfer music files from the computer to play back on
the PVR.
12
S/PDIF optical connector If you have an audio visual sys-
tem with a surround sound decoder or an amplifier
that has optical input, you can use this connector to
link it to your PVR. (Note that multi-channel digi-
tal surround, such as Dolby Digital, is not currently
broadcast on UK digital terrestrial TV channels).
13
RS-232 serial port The serial port connector allows you
to update the software on your PVR using a computer
that does not have a USB connection.
1.4 Connecting up your PVR
As you can see, there is a wide range of connectors on the back
of the PVR, and consequently you can set it up in a number of
different ways. To some extent, the way that you choose will
depend on the other equipment that you have. We’ll cover the
most basic cases here.
The first thing you need to work out is how you will connect
your PVR to your television.
Most modern television sets have one or more connectors for
other equipment, often referred to as AV, EXT or SCART con-
nectors.

1.4 Connecting up your PVR 9
1.4.1 Connecting the aerial to your PVR
Whatever sort of connection you have be-
tween the PVR and the TV, you need to con-
nect the PVR to your television aerial so that
it can receive digital TV channels.
Note that in some areas, you may need to
upgrade your aerial to ensure that you re-
ceive digital television broadcasts — good
reception of existing analogue signals is no
guarantee of good digital reception.
The first connection you should make is to connect a cable from
your TV aerial to the ANT 1 IN connector on the back of the
PVR.
However your PVR is connected to the TV, you must ensure
that there is a connection to both the ANT 1 IN and ANT 2 IN
connectors on your PVR, so that both tuners work properly.
Normally, you do that by using the supplied loop cable to link
from RF LOOP1 OUT to ANT 2 IN.
However, if you are in a weak signal area, or are using a signal
amplifier with more than one output, you may achieve better
results by connecting a cable from the aerial or amplifier di-
rectly to the ANT 2 IN connector, rather than using the loop
cable.

10 Introduction and getting started
1.4.2 Connecting the PVR to your TV using a HDMI cable
For best results with a television set, you
should use a HDMI cable, plugging one end
into the HDMI socket on the PVR, and the
other end into a HDMI socket on your televi-
sion. In this case, you do not have to make
audio connections because the HDMI connec-
tor can output stereo audio or Dolby digital
audio.
1.4.3 Connecting the PVR to your TV using a SCART or AV cable
If your television does not have a HDMI
socket, you should use the supplied SCART
cable for better results than other connections
except HDMI, plugging one end into the TV
SCART socket on the PVR, and the other end
into a free SCART socket on your television.
Some televisions have inputs via S-Video or Composite connec-
tors, rather than HDMI or SCART. If you have such a television,
use an appropriate cable to link the socket on the PVR to the
matching socket on your television.
1.4.4 Connecting to your HiFi system
If you wish to play the sound from the PVR
through your HiFi or audio visual system,
you should connect either the S/PDIF digital
audio connector or the left and right audio
connectors to an input on your audio system.

1.5 Switching on for the first time 11
1.5 Switching on for the first time
Now that you have your PVR connected, you should plug it in
to a mains socket, and switch on at the wall. Ensure that your
television set is turned on and that the correct input or channel
has been selected, so that you will be able to see the display
from the PVR.
Now, press the Standby button on the front of the PVR or on
the remote control. As the PVR starts, the front panel display
will show first C457, followed by the word ‘run’. You will need
to perform some initial set up steps before you can start using
your TF 5810 PVRt.
1.5.1 Searching for TV and radio channels
The first step in setting up your PVR is to search for the avail-
able TV and radio channels.
If there are no channels stored, you will not be able to access
other menu options. If you ever use the Factory Setting op-
tion in the menus to fully reset your PVR, you will have to
perform this procedure again.
When you turn on the PVR, it may automatically display the
Service Search screen. If not, press the MENU button on the
remote control, move to Installation with the arrow buttons,
then press OK. On the next screen, select Service Search and
press OK.
On the next screen, move to Search Mode and ensure that the
Auto option is selected — you can change options by using the
left and right arrows.
All the system menus work in this way; in future, we’ll simply
explain which options to select; remember to move up and
down to highlight menu entries, left and right to change the
options, and OK to select or confirm.

12 Introduction and getting started
Next, move down to Start search, and then press OK button.
The PVR will start to search for channels, and will display a list
of TV and radio services as they are found.
It may take several minutes for the search, and it is common
for no channels to be found until quite late in the process. Be
patient; when the scan is complete, you will see a message
telling you how many TV and radio channels, or services, have
been found. Press OK button to save the list, and then press
the MENU button to move back to the main menu from the
Installation screen.
If you receive signals from more than one transmitter, or are in
a poor reception area, you may miss some channels, or receive
duplicates of others when searching. You can find out how to
resolve this problem in the Advanced Features section of the
manual.
1.5.2 Basic system settings
As well as tuning your PVR in to the available channels, there
are also some other settings that you should check, to ensure
that you get the best performance from your new TF 5810 PVRt.
Remember that you’ll also need to check these settings if you
decide to perform a full reset of your PVR at any time.
1.5.3 Time and date options
First, we’ll set the time options, which ensure that the PVR
knows where it is, and displays the correct time for pro-
grammes in the Electronic Programme Guide. From the Main
menu, choose System Setting, and then Time setting. You
should see a screen like this one.