JVC RX-7001PGD User manual

For Customer Use:
Enter below the Model No. and Serial
No. which are located either on the rear,
bottom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
LVT0396-008A
[U, US]
RX-7001PGD
INSTRUCTIONS
MANUAL DE INSTRUCCIONES
INSTRUÇÕES
RECEPTOR DE CONTROL DE AUDIO/VÍDEO
RECEPTOR DE COMANDO AUDIO/VÍDEO
AUDIO/VIDEO CONTROL RECEIVER
DIGITAL
–+
RX-7001P AUDIO/VIDEO CONTROL RECEIVER
SPEAKERS
12
PHONES
SURROUND ON/OFF
DSP MODE
BALANCE/SURROUND
ADJUST
SEA MODE
SEA ADJUST SETTING
MULTI JOG
MASTER VOLUME
SOURCE SELECTOR
THEATER LIVE CLUB DANCE CLUB HALL PAVILION
INPUT
ANALOG/DIGITAL FM/AM TUNING TUNER PRESET
TUNER/SEA MEMORY FM MODE
DVD
TV SOUND/DBS PHONO
TAPE/MDVCR
FM
AM
CD
SOUND SELECT
INPUT ATT.
BASS BOOST ONETOUCHOPERATION
SOURCENAME
COMPULINK
Remote
DIGITAL
STANDBY
STANDBY/ON
RM-SRX7001P REMOTE CONTROL
CONTROL
CHANNEL VOLUMETV VOL
STOP PAUSE
FF/
/REW
VCR
TV/VIDEO TAPE/MD MUTING
REC
PLAY
DVD DVD MUILTI CD TAPE/MD
TV/DBS PHONO FM/AM
VCR
ANALOG/DIGITAL
SURROUND CENTER
SURROUND
TEST REAR-L
CD-DISC
MODE
ON/OFF
EFFECT REAR-R
SOUND SEA MODE
SUBWOOFER
RETURN
SET
MENU
AUDIO/
TV/VCR
EXIT
TEXT
DISPLAY
SLEEP
123
456
7
/P 89
10
0
+10
100+FM MODE
CATV/DBS
MENUMENU
ENTERENTER
TV/CATV/DBS VCR
TUNING DOWN UP
RX-7001PGD[U,US]COVER/f 00.5.30, 7:03 PM1

Caution –– STANDBY/ON switch!
Disconnect the mains plug to shut the power off completely. The
STANDBY/ON switch in any position does not disconnect the
mains line. The power can be remote controlled.
Precaución –– Interruptor STANDBY/ON !
Desconectarelcabledealimentaciónparadesactivarlaalimentación
totalmente. Cualquier que sea la posición de ajuste del interruptor
STANDBY/ON , la alimentación no es cortada completamente.
La alimentación puede ser controlada remotamente.
Precaução –– Interruptor STANDBY/ON !
Desconectarocabodealimentação paradesligaraalimentaçãopor
completo. Qualquer que seja a posição de ajuste do interruptor
STANDBY/ON ,a alimentaçãonãoécompletamentecortada. A
alimentação pode ser controlada remotamente.
Warnings, Cautions and Others / Avisos, precauciones y otras notas /
Advertêcias, precauções e outras notas /
G-1
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
PRECAUCIÓN
Para reducir riesgos de choques eléctricos, incendio, etc.:
1. No extraiga los tornillos, los cubiertas ni la caja.
2. No exponga este aparato a la lluvia o a la humedad.
ATENÇÃO
Para reduzir riscos de choques eléctricos, incêndio, etc.:
1. Não retire parafusos nem desmonte as tampas ou o gabinete.
2. Não exponha este aparelho à chuva nem à umidade.
RX-7001PGD[U,US]G-page/f 00.5.30, 4:13 PM1

G-2
Español EnglishPortuguês
Caution: Proper Ventilation
To avoide risk of electric shock and fire and to protect from damage.
Locate the apparatus as follows:
Front: No obstructions open spacing.
Sides: No obstructions in 10 cm from the sides.
Top: No obstructions in 10 cm from the top.
Back: No obstructions in 15 cm from the back
Bottom: No obstructions, place on the level surface.
In addition, maintain the best possible air circulation as illustrated.
Precaución: Ventilación Adecuada
Para evitar el riesgo de choque eléctrico e incendio y para proteger el
aparato contra daños.
Ubique el aparato de la siguiente manera:
Frente: Espacio abierto sin obstrucciones
Lados: 10 cm sin obstrucciones a los lados
Parte superior: 10 cm sin obstrucciones en la parte superior
Parte trasera: 15 cm sin obstrucciones en la parte trasera
Fondo: Sin obstrucciones, colóquelo sobre una superficie
nivelada
Además, mantenga la mejor circulación de aire posible como se
ilustra.
Wall or obstructions
Pared u obstrucciones
Parede ou obstáculo Stand height 15 cm or more
Allura del soporte 15 cm o más
Base com altura de 15 cm ou mais
Front
Frente
Frente
Floor
Piso
Piso
Precaução: ventilação apropriada
Paraprevenir o riscode choque elétricoou incêndio epara proteger o
aparelho contra danos.
Localize-o da seguinte maneira:
Frente: Espaço aberto, sem obstruções
Lados: Espaço de 10 cm sem obstruções nos lados
Topo: Espaço de 10 cm sem obstruções acima
Atrás: Espaço de 15 cm sem obstruções atrás
Parte inferior: Sem obstruções. Coloque o aparelho em superfície
nivelada.
Mantenha,além disso, amaior circulação dear possível, comoindica
a ilustração.
Spacing 15 cm or more
Espacio de 15 cm o más
Espaço de 15 cm ou mais
RX-7001PGD
RX-7001PGD[U,US]G-page/f 00.5.30, 4:13 PM2

1
English
Table of Contents
Parts Identification ...................................... 2
Getting Started ........................................... 3
Before Installation ...................................................................... 3
Checking the Supplied Accessories ........................................... 3
Setting the Voltage Selector Switch ........................................... 3
Connecting the FM and AM Antennas ....................................... 3
Connecting the Speakers ............................................................ 4
Connecting Audio/Video Components....................................... 5
Connecting the Power Cord ....................................................... 9
Putting Batteries in the Remote Control .................................... 9
Basic Operations ....................................... 10
Turning the Power On and Off (Standby) ................................ 10
Selecting the Source to Play..................................................... 10
Adjusting the Volume ............................................................... 11
Selecting the Front Speakers .................................................... 11
Muting the Sound ..................................................................... 12
Reinforcing the Bass ................................................................ 12
Attenuating the Input Signal .................................................... 12
Adjusting the Subwoofer Output Level.................................... 12
Basic Settings ........................................... 13
Recording a Source .................................................................. 13
Adjusting the Front Speaker Output Balance........................... 13
Changing the Source Name...................................................... 13
Setting the Subwoofer Information .......................................... 14
Setting the Speakers for the DSP Modes ................................. 14
Digital Input (DIGITAL IN) Terminal Setting ......................... 16
Selecting the Analog or Digital Input Mode ............................ 16
Showing the Text Information on the Display ......................... 17
Setting the AM Tuner Interval Spacing.................................... 17
Storing the Basic Settings and Adjustments — One Touch
Operation ........................................................................... 17
Using the Sleep Timer .............................................................. 17
Receiving Radio Broadcasts ........................ 18
Tuning in Stations Manually .................................................... 18
Using Preset Tuning ................................................................. 18
Selecting the FM Reception Mode........................................... 19
Assigning Names to Preset Stations......................................... 19
Using the SEA Modes ................................ 20
SelectingYour Favorite SEA Mode ........................................... 20
CreatingYour Own SEA Mode ................................................ 20
Using the DSP Modes ................................ 21
Available DSP ModesAccording to the SpeakerArrangement .. 23
Adjusting the 3D-PHONIC Modes .......................................... 24
Adjusting the DAP Modes ....................................................... 24
Adjusting the Surround Modes ................................................ 25
Activating the DSP Modes ....................................................... 27
Using the DVD MULTI Playback Mode .......... 29
Activating the DVD MULTI Playback Mode .......................... 29
Using the On-Screen Menus ........................ 30
Selecting the Source to Play..................................................... 30
Selecting Different Sources for Picture and Sound.................. 30
Activating the DSP Modes ....................................................... 30
Selecting the Analog or Digital Input Mode .............................. 30
Adjusting the Front Speaker Output Balance........................... 31
Reinforcing the Bass ................................................................ 31
Attenuating the Input Signal .................................................... 31
Adjusting the Subwoofer Output Level.................................... 31
Adjusting the DSP Modes ........................................................ 31
Adjusting the DVD MULTI Playback Mode ........................... 32
SelectingYour Favorite SEA Mode ......................................... 32
CreatingYour Own SEA Mode ................................................ 32
Setting the Basic Setting Items ................................................ 33
Operating the Tuner.................................................................. 33
Storing the Preset Stations ....................................................... 34
Assigning Names to Preset Stations......................................... 34
COMPU LINK Remote Control System ......... 35
TEXT COMPU LINK Remote Control System .. 36
Showing the Disc Information on the TV Screen .................... 37
Searching for a Disc (Only for the CD player) ........................ 38
Entering the Disc Information.................................................. 39
AV COMPU LINK Remote Control System .... 41
Operating JVC’s Audio/Video Components ... 43
Operating Audio Components.................................................. 43
Operating Video Components .................................................. 45
Operating Other Manufacturers’ Video
Equipment ............................................ 46
Troubleshooting ......................................... 52
Specifications ............................................ 53
EN01-09.RX-7001PGD[U,US]/f 00.5.31, 10:52 AM1

2
English
Parts Identification
Become familiar with the buttons and controls on the receiver before use.
Refer to the pages in parentheses for details.
RM-SRX7001P REMOTE CONTROL
CONTROL
CHANNEL VOLUMETV VOL
TUNING
STOP PAUSE
FF/
/REW
VCR
TV/VIDEO TAPE/MD MUTING
REC
PLAY
DOWN UP
DVD DVD MUILTI CD TAPE/MD
TV/DBS PHONO FM/AM
VCR
ANALOG/DIGITAL
SURROUND CENTER
SURROUND
TEST REAR-L
CD-DISC
MODE
ON/OFF
EFFECT REAR-R
SOUND SEA MODE
SUBWOOFER
RETURN FM MODE
SET
MENU
AUDIO/
TV/VCR
EXIT
TEXT
DISPLAY
SLEEP
123
456
7
/P 89
10
0
+10
100+
CATV/DBS
MENUMENU
ENTERENTER
1
2
3
4
5
6
7
8
9
o
i
u
y
t
r
e
w
q
p

TV/CATV/DBS VCR
Front Panel
1STANDBY/ON button and STANDBY
lamp (10)
2Remote sensor (9)
3SURROUND ON/OFF button and lamp (26, 27)
4SEA MODE button (20)
5INPUT ANALOG/DIGITAL button (16)
6FM/AM TUNING button (18)*
7FM MODE button (19)
8Display (10)
9Source lamps (10)
pMASTER VOLUME control (11)
qPHONES jack (12)
wSPEAKERS 1/2 buttons and lamps (11)
eDSP MODE button (24)
rBALANCE/SURROUND ADJUST button
(12, 13, 24)*
tSEA ADJUST button (20)*
ySETTING button (14 – 17)*
uTUNER/SEA MEMORY button (18 – 20)
iSOUND SELECT/INPUT ATT. button
(11, 12)
oBASS BOOST/SOURCE NAME button
(12, 13)
;ONE TOUCH OPERATION button and lamp
(17)
aTUNER PRESET button (19)*
sMULTI JOG control
Whatthiscontrolactuallydoesdepends on which
function you are trying to adjust. Before using
this control, select the function by pressing one
of the buttons marked with *.
dSOURCE SELECTOR control (10)
Remote Control
1TV/CATV/DBS button (45, 46)
2Source selecting buttons (10)
DVD, DVD MULTI, CD, TAPE/MD, TV/DBS,
PHONO, FM/AM, VCR
3SURROUND ON/OFF button (25, 27)
4SURROUND MODE button (25, 26)
5CD-DISC button (44)
6SOUND button (20, 24, 29)
7On-screen operation buttons (30, 37)
MENU, SET, EXIT, %, fi, @, #
8TV VOL +/– buttons (45, 46)
9Operating buttons for audio/video components
(43 – 47)
pAUDIO buttons , (10)
qVCR button (45, 47)
wSLEEP button (17)
eANALOG/DIGITAL button (16)
r• 10 keys for selecting preset channels (19)
• 10 keys for adjusting sound (20, 24 – 27, 29)
• 10 keys for operating audio/video components
(43 – 47)
tRemote control mode selector (10, 43, 46)
yTEXT DISPLAY button (37)
uCHANNEL +/– buttons (45 – 47)
iVOLUME +/– buttons (11)
oMUTING button (12)
–+
AUDIO/VIDEO CONTROL RECEIVERRX-7001P
SPEAKERS
12
PHONES
SURROUND ON/OFF
DSP MODE
BALANCE/SURROUND
ADJUST
SEA MODE
SEA ADJUST SETTING
MULTI JOG
MASTER VOLUME
SOURCE SELECTOR
INPUT
ANALOG/DIGITAL
FM/AM TUNING TUNER PRESET
TUNER/SEA MEMORY FM MODE
DVD
TV SOUND/DBS PHONO
TAPE/MDVCR
FM
AM
THEATER LIVE CLUB DANCE CLUB HALL PAVILION
CD
SOUND SELECT
INPUT ATT.
BASS BOOST ONETOUCHOPERATION
SOURCENAME
COMPULINK
Remote
DIGITAL
12345 67 8 9 p
dsa;oiuytrewq
STANDBY
STANDBY/ON
EN01-09.RX-7001PGD[U,US]/f 00.5.31, 10:53 AM2

3
English
ANTENNA
AM
EXT
AM
LOOP
FM 75
COAXIAL
AM
LOOP
ANTENNA
AM
EXT
FM 75
COAXIAL
AM
LOOP
ANTENNA
AM
EXT
FM 75
COAXIAL
Getting Started
This section explains how to connect audio/video components and speakers to the receiver, and how to connect the
power supply.
Before Installation
General
• Be sure your hands are dry.
• Turn the power off to all components.
• Read the manuals supplied with the components you are going to
connect.
Locations
• Install the receiver in a location that is level and protected from
moisture.
• The temperature around the receiver must be between –5˚C and
35˚C (23˚F and 95˚F).
• Make sure there is good ventilation around the receiver. Poor
ventilation could cause overheating and damage the receiver.
Handling the receiver
• Do not insert any metal object into the receiver.
• Do not disassemble the receiver or remove screws, covers, or
cabinet.
• Do not expose the receiver to rain or moisture.
Checking the Supplied Accessories
Check to be sure you have all of the following items, which are
supplied with the receiver.
The number in the parentheses indicates quantity of the pieces
supplied.
• Remote Control (1)
• Batteries (2)
• AM LoopAntenna (1)
• FMAntenna (1)
• AC Plug Adaptor (1)
If anything is missing, contact your dealer immediately.
Setting the Voltage Selector Switch
Before connections, always do the following first if necessary.
Set the correct voltage for your area with the voltage selector switch
on the rear panel. Use a screw driver to rotate the switch so the
number the arrow is pointing at is the same as the voltage where you
are plugging in the receiver.
A. Using the Supplied FMAntenna
The FM antenna provided can be connected to the FM 75 Ω
COAXIAL terminal as temporary measure.
B. Using the Standard Type Connector (Not Supplied)
A standard type connector should be connected to the FM 75 Ω
COAXIAL terminal.
Note:
If reception is poor, connect the outdoor antenna.
Before attaching a 75 Ω coaxial cable (the kind with a round wire
going to an outdoor antenna), disconnect the supplied FM antenna.
Connecting the FM and AM
Antennas
FM Antenna Connections
B
FM Antenna
Outdoor FM Antenna Cable
Extend the supplied FM antenna horizontally.
A
VOLTAGE SELECTOR
220V
230 - 240V
127V
110V
Voltage Mark
EN01-09.RX-7001PGD[U,US]/f 00.5.31, 10:53 AM3

4
English
Basic connecting procedure
1 Cut, twist and remove the insulation at the end of
each speaker signal cable (not supplied).
2 Turn the knob counterclockwise.
3 Insert the speaker signal cable.
4 Turn the knob clockwise.
Connecting the front speakers
You can connect two pairs of front speakers (one pair to the FRONT
SPEAKERS 1terminals, and another pair to the FRONT
SPEAKERS 2terminals).
AM Loop Antenna
Snap the tabs on the loop into the
slots of the base to assemble the
AM loop.
Turn the loop until you have the best reception.
Notes:
• Make sure the antenna conductors do not touch any other
terminals, connecting cords and power cord.This could cause poor
reception.
• If reception is poor, connect an outdoor single vinyl-covered wire to
the AM EXT terminal. (Keep the AM loop antenna connected.)
Connecting the Speakers
You can connect the following speakers:
• Two pairs of front speakers to produce normal stereo sound.
• One pair of rear speakers to enjoy the surround effect.
• One center speaker to produce more effective surround effect (to
emphasize human voices).
• One subwoofer to enhance the bass.
IMPORTANT:
After connecting the speakers listed above, set the speaker
setting information properly to obtain the best possible DSP
effect. For details, see page 14.
For each speaker (except for a subwoofer), connect the (–) and (+)
terminals on the rear panel to the (–) and (+) terminals marked on
the speakers. For connecting a subwoofer, see page 5.
ANTENNA
AM
EXT
AM
LOOP
FM 75
COAXIAL
23
1
2
1
RIGHT
1
3
RIGHT
1
4
FRONT SPEAKERS 1Left speaker
Right speaker
CAUTION:
Use speakers with the SPEAKER IMPEDANCE indicated by the
speaker terminals.
FRONT SPEAKERS 2Left speaker Right speaker
AM Antenna Connections
+– +–
RIGHT LEFT
1
2
1
2
FRONT SPEAKERS
Outdoor single vinyl-covered wire (not supplied)
RIGHT
1
EN01-09.RX-7001PGD[U,US]/f 00.5.31, 10:53 AM4

5
English
About the speaker impedance
The required speaker impedance of the front speakers does differ
depending on whether both the FRONT SPEAKERS 1and FRONT
SPEAKERS 2terminals are used or only one of them is used.
CASE 1 When you connect only one set of front speakers
Front
speaker
1
Front
speaker
1
Use front speakers with 8 Ω – 16 Ωimpedance.
CASE 2 When you connect two sets of front speakers
Front
speaker
1
Front
speaker
2
Use front speakers 16 Ω – 32 Ωimpedance.
Connecting the subwoofer speaker
You can enhance the bass by connecting a subwoofer.
Connect the input jack of a powered subwoofer to the
SUBWOOFER OUT jack on the rear panel, using a cable with RCA
pin plugs (not supplied).
SUBWOOFER
OUT
Powered subwoofer
Connecting Audio/Video Components
You can connect the following audio/video components to this
receiver. Refer also to the manuals supplied with your components.
Audio Components Video Components
• Turntable • DVD player*
• CD player* • TV*
• Cassette deck • DBS tuner*
or MD recorder* • VCR
* You can connect these components using the methods described in
“Analog connections” (below) or in “Digital connections” (see page
8).
Analog connections
Audio component connections
Use the cables with RCA pin plugs (not supplied).
Connect the white plug to the audio left jack, and the red plug to the
audio right jack.
CAUTION:
If you connect a sound-enhancing device such as a graphic equalizer
between the source components and this receiver, the sound output
through this receiver may be distorted.
Turntable
To audio output
Turntable
Note:
Any turntables incorporating a small-output cartridge such as an MC
(moving-coil) type must be connected to this receiver through a
commercial head amplifier or step-up transformer. Direct connection
may result in insufficient volume.
Front
speaker
2
Front
speaker
1
Connecting the rear and center speakers
Connect rear speakers to the REAR SPEAKERS terminals and a
center speaker to the CENTER SPEAKER terminals.
Left rear
speaker Right rear
speaker
Center
speaker
+
–
+
–
CENTER
SPEAKER REAR
SPEAKERS
RIGHT LEFT
12
RIGHT LEFT
TAPE
/MD
IN
(PLAY)
OUT
(REC)
CD
PHONO
AUDIO
If an earth cable is provided for your
turntable, connect the cable to the
screw marked (H) on the rear panel.
EN01-09.RX-7001PGD[U,US]/f 00.5.31, 10:53 AM5

6
English
RIGHT LEFT
TAPE
/MD
IN
(PLAY)
OUT
(REC)
CD
PHONO
AUDIO
To audio output
CD player
Cassette deck or MD recorder
To audio input
Cassette deck
To audio output
RIGHT LEFT
TAPE
/MD
IN
(PLAY)
OUT
(REC)
CD
PHONO
AUDIO
MD recorder
To audio input To audio output
CD player
Note:
You can connect either a cassette deck or an MD recorder to the
TAPE/MD jacks. When connecting an MD recorder to the TAPE/MD
jacks, change the source name, which will be shown on the display
when selected as the source, to “MD.” See page 13 for details.
If your audio components have a COMPU LINK-3 or TEXT
COMPU LINK jack
• See also page 35 for detailed information about the connection and
the COMPU LINK-3 remote control system.
• See also page 36 for detailed information about the connection and
the TEXT COMPU LINK remote control system.
Video component connections
Use the cables with RCA pin plugs (not supplied).
Connect the white plug to the audio left jack, the red plug to the
audio right jack, and the yellow plug to the video jack.
If your video components have S-video (Y/C-separation) terminals,
connect them using S-video cables (not supplied). Connecting these
video components through the S-video input/output terminals will
give you better picture playback (or recording) quality.
IMPORTANT:
This receiver is equipped with both the composite video and S-video
input/output terminals for connecting video components.
You do not have to connect both the composite video and S-video
terminals.
However, remember that the video signals from the composite
video input terminals are output only through the composite
video output terminals, while the ones from the S-video input
terminals are output only through the S-video output terminals.
Therefore, if a recording video component and a playing video
component are connected to the receiver through the different video
terminals, you cannot record the picture from the playing component
on the recording component. In addition, if the TV and a playing video
component are connected to the receiver through the different video
terminals, you cannot view the playback picture from the playing
component on the TV.
VCR
ÅTo left/right channel audio output
ıTo left/right channel audio input
ÇTo S-video output
ÎTo composite video output
‰To composite video input
ÏTo S-video input
S-VHS (or VHS) VCR
VIDEO
VIDEO S-VIDEORIGHT LEFT
AUDIO
VCR
IN
(PLAY)
OUT
(REC)
TV SOUND
/DBS
DVD
A
BEF
DC
EN01-09.RX-7001PGD[U,US]/f 00.5.31, 10:53 AM6

7
English
RIGHT
VIDEO
VIDEO S-VIDEORIGHT LEFT
AUDIO
MONITOR
OUT
VCR
IN
(PLAY)
OUT
(REC)
TV SOUND
/DBS
DVD
TV and/or DBS tuner
When connecting the TV, DO NOT connect the
TV’s video output to these video input terminals.
Connect the TV to the MONITOR
OUT jack to view the playback
picture from the other connected
video components.
To S-video input
To composite video input
To audio
output
DBS
RIGHT
VIDEO
VIDEO S-VIDEORIGHT LEFT
AUDIO
IN
(PLAY)
OUT
(REC)
IN
(PLAY)
OUT
(REC)
TV SOUND
/DBS
DVD
VCR 2
DBS tuner
To audio
output
To composite video output
To S-video output
Note:
When connecting the DBS tuner to the TV SOUND/DBS jacks,
change the source name, which will be shown on the display when
selected as the source, to “DBS.” See page 13 for details.
ÅTo center channel audio output
ıTo subwoofer audio output
ÇTo S-video output
ÎTo front left/right channel audio output
‰To rear left/right channel audio output
ÏTo composite video output
VIDEO
VIDEO S-VIDEORIGHT LEFT
AUDIO
VCR
IN
(PLAY)
OUT
(REC)
TV SOUND
/DBS
DVD
DVD
DVD
CENTER
SUB
WOOFER
A
ED
BC
F
DVD player
DVD player
• When you connect the DVD player with stereo output jacks:
DVD player
ÅTo front left/right channel audio output (or to audio mixed
output if necessary)
ıTo S-video output
ÇTo composite video output
DVD
VIDEO
VIDEO S-VIDEORIGHT LEFT
AUDIO
DVD
ABC
• When you connect the DVD player with its analog discrete output
(5.1 CH reproduction) jacks:
Note:
Use a TV of the PAL- or multi-color system.
TV
EN01-09.RX-7001PGD[U,US]/f 00.5.31, 10:53 AM7

8
English
DIGITALOUT
PCM/DOLBYDIGITAL/MPEG/DTS
DVD
DIGITALIN
DIGITAL3 (TV)
DIGITAL2 (CD)
DIGITAL1 (DVD)
PCM/DOLBYDIGITAL
MPEG/DTS
DBS
Digital connections
This receiver is equipped with three DIGITAL IN terminals — one
digital coaxial terminal and two digital optical terminals, and one
DIGITAL OUT terminal.
You can connect any digital equipment such as —
• DBS tuner,
• Digital TV broadcast tuner,
• DVD player,
• CD player,
• and MD recorder.
IMPORTANT:
• When connecting the DVD player, digital TV broadcast tuner or DBS
tuner using the digital terminals, you also need to connect it to the
video jack (either composite video terminal or S-video terminal) on
the rear. Without connecting it to the video jack, you can view no
playbackpicture.
• After connecting the components using the DIGITAL IN terminals,
set the following correctly if necessary.
– Set the digital input (DIGITAL IN) terminal setting correctly. For
details, see “Digital Input (DIGITAL IN) Terminal Setting” on page
16.
– Select the digital input mode correctly. For details, see “Selecting
the Analog or Digital Input Mode” on page 16.
Notes:
• When shipped from the factory, the DIGITAL IN terminals have
been set for use with the following components.
– DIGITAL 1 (coaxial): For DVD player
– DIGITAL 2 (optical): For CD player
– DIGITAL 3 (optical): For digital TV broadcast tuner
• When you want to operate the CD player or MD recorder using the
COMPU LINK remote control system, connect the target
component also as described in “Analog connections” (see pages 5
and 6).
• When you want to operate the DVD player using the AV COMPU
LINK remote control system, connect the DVD player also as
described in “Analog connections” (see page 7).
Digital output terminal
Digital optical cable (not supplied)
between digital optical terminals
When the digital recording
equipment such as an MD recorder
has a digital optical input terminal,
connecting it to the DIGITAL OUT
terminal enables you to perform
digital-to-digital recording.
MD recorder
DVD playerDBS tuner
CD player
When the component has a digital
optical output terminal, connect it to the
DIGITAL 2 (CD), or DIGITAL 3 (TV)
terminal, using the digital optical cable
(not supplied).
When the component has a digital
coaxial output terminal, connect it to the
DIGITAL 1 (DVD) terminal, using the
digital coaxial cable (not supplied).
Digital coaxial cable (not supplied)
between digital coaxial terminals
Digital optical cable (not supplied)
between digital optical terminals
Digital input terminals
Before connecting a digital
optical cable, unplug the
protective plug.
MD recorder, etc.
EN01-09.RX-7001PGD[U,US]/f 00.5.31, 10:53 AM8

9
English
3
1
2
R6P(SUM-3)/AA(15F)
Connecting the Power Cord
Before plugging the receiver into an AC outlet, make sure that all
connections have been made.
Plug the power cord into an AC outlet.
Keep the power cord away from the connecting cables and the
antenna. The power cord may cause noise or screen interference. We
recommend that you use a coaxial cable to connect the antenna,
since it is well-shielded against interference.
Notes:
• The preset settings such as preset channels and sound adjustment
may be erased in a few days in the following cases:
–When you unplug the power cord.
–When a power failure occurs.
• If the wall outlet does not match the AC plug, use the supplied AC
plug adaptor.
CAUTIONS:
• Do not plug in before setting the voltage selector switch on the
rear of the unit and all connection procedures are complete.
• Do not touch the power cord with wet hands.
• Do not pull on the power cord to unplug the cord. When
unplugging the cord, always grasp the plug so as not to damage
the cord.
Putting Batteries in the Remote Control
Before using the remote control, put two supplied batteries first.
When using the remote control, aim the remote control directly at
the remote sensor on the receiver.
1. On the back of the remote control, remove the
battery cover.
2. Insert batteries. Make sure to match the polarity:
(+) to (+).
3. Replace the cover.
If the range or effectiveness of the remote control decreases, replace
the batteries. Use two R6P(SUM-3)/AA(15F) type dry-cell batteries.
CAUTION:
Follow these precautions to avoid leaking or cracking cells:
• Place batteries in the remote control so they match the polarity:
(+) to (+).
• Use the correct type of batteries. Batteries that look similar may
differ in voltage.
• Always replace both batteries at the same time.
• Do not expose batteries to heat or flame.
EN01-09.RX-7001PGD[U,US]/f 00.5.31, 10:53 AM9

10
English
Basic Operations
The following operations are commonly used when you play any sound source.
From the remote control:
Press one of the source selecting buttons.
AUDIO/
TV/VCR
CATV/DBS
STANDBY
STANDBY/ON
Current source name appears
SOURCE SELECTOR
DVD
TV SOUND/DBS PHONO
TAPE/MDVCR
FM
AM
CD
Selected source name appears
DVD Select the DVD player.
DVDMULTI Select the DVD player for viewing the digital video
disc using the analog discrete output mode (5.1CH
reproduction) on the DVD player.
To enjoy the DVD MULTI playback, see page 29.
CD* Select the CD player.
TAPE/MD* Select the cassette deck (or the MD recorder).
TV/DBS Select TV sounds (or the DBS tuner).
PHONO* Select the turntable.
FM/AM* Select an FM or AM broadcast.
• Each time you press the button, the band alternates
between FM and AM.
VCR Select the video component connected to the VCR
jacks.
Notes:
• When connecting an MD recorder (to the TAPE/MD jacks), and a
DBS tuner (to the TV SOUND/DBS jacks), change the source name
shown on the display. For details, see page 13.
• When you press one of the source selecting buttons on the remote
control marked above with an asterisk ( * ), the receiver
automatically turns on.
DVD DVD MUILTI CD TAPE/MD
TV/DBS PHONO FM/AM
VCR
IMPORTANT:
When using the remote control, check to see if its
remote control mode selector is set to the correct
position:
To operate this receiver, set it to “AUDIO/TV/
VCR.”
Turning the Power On and Off (Standby)
On the front panel:
To turn on the power, press STANDBY/ON
. The STANDBY lamp goes off. The name
of the current source (or station frequency)
appears on the display.
To turn off the power (into standby mode),
press STANDBY/ON again.
The STANDBY lamp lights up. A small amount
of power is consumed in standby mode. To turn
the power off completely, unplug the AC power
cord.
From the remote control:
To turn on the power, press AUDIO .
The STANDBY lamp goes off. The name of
the current source (or station frequency)
appears on the display.
To turn off the power (into standby mode),
press AUDIO . The STANDBY
lamp lights up.
Selecting the Source to Play
On the front panel:
Turn SOURCE SELECTOR until the source
name you want appears on the display.
• As you turn the selector, the source changes as
follows:
CD OPHONO OTAPE (or MD) OFM O
AM ODVD ODVD MULTI O
TV SOUND (or DBS) OVCR O
(back to the beginning)
The selected source lamp also lights up.
• The DVD lamp lights up both for “DVD” and
“DVD MULTI.”
Current volume level is shown here
STANDBY
STANDBY/ON
EN10_19.RX-7001PGD[U,US]/f 00.5.31, 10:54 AM10

11
English
Signal and speaker indicators on the display
• The signal indicators light up to indicate the incoming channel
signals.
– Only the indicators for the incoming signals light up.
• The frame of the signal indicator (except for “LFE” and “S”)
lights up if the corresponding speaker is set to “LARGE” or
“SMALL” (for subwoofer, “YES”).
– The frames of “L” and “R” indicators always light up.
L:•When digital input is selected: Lights up when the left
channel signal comes in.
•When analog input is selected: Always lights up.
R:•When digital input is selected: Lights up when the right
channel signal comes in.
•When analog input is selected: Always lights up.
C: Lights up when the center channel signal comes in.
LS: Lights up when the left rear channel signal comes in.
RS: Lights up when the right rear channel signal comes in.
S: Lights up when the monaural rear channel signal comes in.
LFE: Lights up when the LFE channel signal comes in.
Notes:
• When “SUBWOOFER” is set to “YES,”
SUBWFR
lights up.
• When you select “DVD MULTI,” all the signal indicators except “S”
light up.
Selecting different sources for picture and
sound
You can watch picture from a video component while listening to
sound from another component.
On the front panel:
1. Press SOUND SELECT (INPUT
ATT.) briefly while viewing the
picture from a video component
such as the VCR or DVD player,
etc.
“SOUND SELECT” appears on the display.
2. Turn SOURCE SELECTOR to
select the sound (except the TV
sound), while the indication of the
above step is still on the display.
From the remote control:
Press one of the audio source selecting buttons (CD, TAPE/MD,
PHONO, FM/AM, TV/DBS*), while viewing the picture from a
video component such as the VCR or DVD player, etc.
Notes:
• Once you have selected a video source, pictures of the selected
source are sent to the TV until you select another video source.
* The TV/DBS button only works for selecting “DBS” as the source
but not for selecting “TV SOUND.” When you use the DBS tuner,
change the source name correctly (see page 13).
Adjusting the Volume
On the front panel:
To increase the volume, turn MASTER
VOLUME clockwise.
To decrease the volume, turn it
counterclockwise.
• When you turn MASTER VOLUME rapidly,
the volume level also changes rapidly.
• When you turn MASTER VOLUME slowly,
the volume level also changes slowly.
From the remote control:
To increase the volume, press VOLUME +.
To decrease the volume, press VOLUME –.
CAUTION:
Always set the volume to the minimum before starting any source. If
the volume is set at its high level, the sudden blast of sound energy
can permanently damage your hearing and/or ruin your speakers.
Note:
The volume level can be adjusted within the range of “0” (minimum) to
“90” (maximum).
Selecting the Front Speakers
On the front panel ONLY:
When you have connected two pairs of the front speakers, you can
select which to use.
Press SPEAKERS 1 or SPEAKERS 2 to select
the speaker to use.
• Each time you press the button, the lamp on
the respective button turns on and off. When
the lamp on either button lights up, the
respective speakers are activated.
Note:
If you use any of the DSP modes other than the 3D-PHONIC modes
with both front speakers activated, the speakers connected to the
FRONT SPEAKERS 2 terminals are deactivated.
VOLUME
SPEAKERS
12
S
C
LS
LLFESUBWFR RS R
SOUND SELECT
INPUT ATT.
SOURCE SELECTOR
–+
MASTER VOLUME
EN10_19.RX-7001PGD[U,US]/f 00.5.31, 10:54 AM11

12
English
Listening only with headphones
You can listen with the headphones without deactivating both pairs
of speakers; however, if you want to use the HEADPHONE mode
(see below), you must turn off both pairs of speakers.
1. Connect a pair of headphones to the PHONES jack on the front
panel.
2. Press SPEAKERS 1 and/or 2 so that no lamps on the buttons are
turned on.
This cancels the surround mode or DSP mode currently selected,
and activates the HEADPHONE mode (see below).
• The HEAD PHONE indicator lights up on the display.
HEADPHONE mode:
This mode can reproduce the LFE channel signals, mixing them
with the front channel signals. So you will not miss the
subwoofer sounds even if you listen to a source using the
headphones.
Notes:
• While in the HEADPHONE mode, you cannot use any other DSP
modes (see page 21.)
• Activating the speaker cancels the headphones mode and turns on
the DSP mode previously selected.
CAUTION:
Be sure to turn down the volume before connecting or putting on
headphones, as high volume can damage both the headphones and
your hearing.
Muting the Sound
From the remote control ONLY:
Press MUTING to mute the sound through all
speakers and headphones connected.
“MUTING” appears on the display and the
volume turns off (the volume level indicator goes
off).
To restore the sound, press MUTING again so that “OFF” appears
on the display.
• Turning MASTER VOLUME on the front panel or pressing
VOLUME +/– on the remote control also restores the sound.
Reinforcing the Bass
You can boost the bass level.
On the front panel ONLY:
Press BASS BOOST (SOURCE NAME)
briefly to select the bass boost function.
• Each time you press the button, the bass boost
function turns on (“BASSBOOST ON”) and
off (“BASSBOOST OFF”).
– Select “BASSBOOST ON” to activate the bass boost function.
The BASS BOOST indicator lights up on the display.
– Select “BASSBOOST OFF” to cancel it.
The indicator goes off.
Note:
This function affects the front speaker sounds only.
Attenuating the Input Signal
When the input level of the playing source is too high, the sounds
will be distorted. If this happens, you need to attenuate the input
signal level to prevent the sound distortion.
On the front panel ONLY:
Press and hold INPUT ATT. (SOUND
SELECT) so that the ATT indicator lights up
on the display.
• Each time you press and hold the button, the
Input Attenuator mode turns on (“INPUT ATT
ON”) or off (“INPUT NORMAL”).
Notes:
• This function is available only for the sources connected using the
analog terminals.
• This function takes effect when the DSP mode is in use.
• When selecting “DVD MULTI” as the source, this effect does not
work.
Adjusting the Subwoofer Output Level
You can adjust the subwoofer output level if you have selected
“YES” for the “SUBWOOFER” (see page 14).
Once it has been adjusted, the receiver memorizes the adjustment.
Before you start, remember....
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
• When the front speakers are all deactivated, the subwoofer level
cannot be adjusted.
On the front panel:
1. Press (BALANCE/) SURROUND
ADJUST repeatedly until
“SUBWFR LEVEL” appears on
the display.
The display changes to show the current setting.
2. Turn MULTI JOG to adjust the
subwoofer output level (–10 dB to
+10 dB).
From the remote control:
1. Press SOUND.
The 10 keys are activated for sound adjustments.
2. Press SUBWOOFER –/+ to adjust
the subwoofer output level (–10 dB
to +10 dB).
SOUND SELECT
INPUT ATT.
SOUND
BALANCE/SURROUND
ADJUST
MULTI JOG
SUBWOOFER
0
+10
100+FM MODE
MUTING
BASS BOOST
SOURCENAME
EN10_19.RX-7001PGD[U,US]/f 00.5.31, 10:54 AM12

13
English
Basic Settings
Some of the following settings are required after connecting and positioning your speakers in your listening room, while
others will make operations easier.
IMPORTANT:
When using the remote control, check to see if its
remote control mode selector is set to the correct
position:
To operate this receiver, set it to “AUDIO/TV/
VCR.”
Recording a Source
For analog-to-analog recording
You can record any analog source through the receiver to —
• the cassette deck (or MD recorder) connected to the TAPE/MD
jacks, and
• the VCR connected to the VCR jacks
— at the same time.
For digital-to-digital recording
You can record the currently selected digital input through the
receiver to a digital recording device connected to the DIGITAL
OUT terminal.
Notes:
• Analog-to-digital and digital-to-analog recordings are not possible.
• The output volume level, bass boost (see page 12), SEA modes
(see page 20), and DSP modes (see page 21) cannot affect the
recording.
• The test tone signal (see page 25, 26) does not come out through
the DIGITAL OUT terminal.
Adjusting the Front Speaker Output
Balance
If the sounds you hear from the front right and left speakers are
unequal, you can adjust the speaker output balance.
Before you start, remember...
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
On the front panel ONLY:
1. Press BALANCE (/SURROUND)
ADJUST repeatedly until “L/R
BALANCE” appears on the
display.
The display changes to show the current setting.
AUDIO/
TV/VCR
CATV/DBS
MULTI JOG
2. Turn MULTI JOG to adjust the
balance.
• Turning it clockwise decreases the left
channel output.
• Turning it counterclockwise decreases the
right channel output.
Changing the Source Name
When you have connected an MD recorder to the TAPE/MD jacks
or the DBS tuner to the TV SOUND/DBS jacks on the rear panel,
change the source name which will be shown on the display when
you select the MD recorder or DBS tuner as the source.
On the front panel ONLY:
1. When changing the source name
from “TAPE” to “MD”:
• Turn SOURCE SELECTOR
until “TAPE” appears.
When changing the source name from “TV
SOUND” to “DBS”:
• Turn SOURCE SELECTOR until “TV
SOUND” appears.
2. Press and hold SOURCE NAME
(BASS BOOST) until “ASSGN.
MD” or “ASSGN. DBS” appears
on the display.
To change the source name to “TAPE” or “TV SOUND,” repeat
the same procedure above — in step 1, select “MD” or “DBS” then
press and hold SOURCE NAME (BASS BOOST).
Note:
Without changing the source name, you can still use the connected
components. However, there may be some inconvenience.
– “TAPE” or “TV SOUND” will appear on the display when you select
the MD recorder or DBS tuner.
– You cannot use the digital input (see page 16) for the MD recorder.
– You cannot use the COMPU LINK remote control system (see page
35) to operate the MD recorder.
SOURCE SELECTOR
BASS BOOST
SOURCENAME
BALANCE/SURROUND
ADJUST
EN10_19.RX-7001PGD[U,US]/f 00.5.31, 10:54 AM13

14
English
3. Repeat steps 1 and 2 to select the appropriate
items for the other speakers.
Notes:
• Keep the following comment in mind as reference when adjusting.
– If the size of the cone speaker unit built in your speaker is greater
than 12 cm, select “LARGE,” and if it is smaller than 12 cm,
select “SMALL.”
• If you have selected “NO” for the subwoofer setting, you can only
select “LARGE” for the front speaker setting.
• If you have selected “SMALL” for the front speaker setting, you
cannot select “LARGE” for the center and rear speaker settings.
Center Delay Time Setting
Register the delay time of the sound from the center speaker,
comparing to that of the sound from the front speakers.
If the distance from your listening point to the center speaker is
equal to that to the front speakers, select 0 msec. As the distance to
the center speaker becomes shorter, increase the delay time.
• 1 msec increase (or decrease) in delay time corresponds to 30 cm
decrease (or increase) in distance.
• When shipped from the factory, delay time is set to 0 msec.
On the front panel ONLY:
1. Press SETTING repeatedly until
“CENTER DELAY” appears on
the display.
The display changes to show the current setting.
2. Turn MULTI JOG to select the
delay time of the center speaker
output.
• Turn it clockwise to increase the delay time from 0 msec (“C.
DELAY: 0ms”) to 5 msec (“C. DELAY: 5ms”).
• Turn it counterclockwise to decrease the delay time from
5 msec (“C. DELAY: 5ms”) to 0 msec (“C. DELAY: 0ms”).
Notes:
• Center delay time setting is not valid for the DVD MULTI playback
mode.
• You cannot adjust the center delay time when you have set
“CENTER SPK” to “NONE.”
Rear Delay Time Setting
Register the delay time of the sound from the rear speakers,
comparing to that of the sound from the front speakers.
If the distance from your listening point to the rear speakers is equal
to that to the front speakers, select 0 msec.As the distance to the
rear speakers becomes shorter, increase the delay time.
• 1 msec increase (or decrease) in delay time corresponds to 30 cm
decrease (or increase) in distance.
• Rear delay time for Dolby Digital, DTS Digital Surround and
MPEG Multichannel is to be set to 5 msec.
• When shipped from the factory, delay time is set to 5 msec.
On the front panel ONLY:
1. Press SETTING repeatedly until
“REAR DELAY” appears on the
display.
The display changes to show the current setting.
Setting the Subwoofer Information
Register whether or not you have connected a subwoofer.
Before you start, remember...
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
On the front panel ONLY:
1. Press SETTING repeatedly until
“SUBWOOFER” appears on the
display.
The display changes to show the current setting.
2. Turn MULTI JOG to register
whether you have connected a
subwoofer or not.
• As you turn it, the subwoofer setting alternates between
“YES” and “NO.”
YES: Select this when a subwoofer is used.
SUBWFR
lights
up on the display (see page 11).
NO: Select this when no subwoofer is used.
Setting the Speakers for the DSP Modes
To obtain the best possible surround sound of the DSP modes, you
have to register the information about the speakers arrangement after
all connections are completed.
Before you start, remember...
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
Front, Center, and Rear Speaker Setting
Register the sizes of all the connected speakers.
• When you change your speakers, you need to register the
information about the speakers again.
On the front panel ONLY:
1. Press SETTING repeatedly until
“FRONT SPK” (Front Speaker),
“CENTER SPK” (Center
Speaker) or “REAR SPK” (Rear
Speaker) appears on the display.
The display changes to show the current setting.
2. Turn MULTI JOG to select the
appropriate item about the speaker
selected in the above step.
• As you turn it, the display changes to show the following:
LARGE: Select this when the speaker size is relatively large.
SMALL: Select this when the speaker size is relatively small.
NONE: Select this when you have not connected a speaker.
(Not selectable for the front speakers.)
SETTING
MULTI JOG
MULTI JOG
SETTING
MULTI JOG
SETTING
LARGE SMALL NONE
SETTING
EN10_19.RX-7001PGD[U,US]/f 00.5.31, 10:54 AM14

15
English
2. Turn MULTI JOG to select the
delay time of the rear speaker
output.
• Turn it clockwise to increase the delay time
from 0 msec (“R. DELAY: 0ms”) to
15 msec (“R. DELAY: 15ms”).
• Turn it counterclockwise to decrease the delay time from
15 msec (“R. DELAY: 15ms”) to 0 msec (“R. DELAY: 0ms”).
Notes:
• Rear delay time setting is not valid for the DVD MULTI playback
mode.
• You cannot adjust the rear delay time when you have set “REAR
SPK” to “NONE.”
Crossover Frequency Setting
Small speakers cannot reproduce the bass sound very well. So, if
you have used a small speaker for any of the front, center, and rear
channels, this receiver automatically reallocate the bass elements,
originally assigned to the channel for which you have connected the
small speaker, to another channel (for which you have connected the
large speaker).
To use this function properly, you need to set the crossover
frequency level according to the size of the small speaker connected.
• If you have selected “LARGE” for all speakers (see page 14), this
function is set to “OFF” and cannot be adjusted.
On the front panel ONLY:
1. Press SETTING repeatedly until
“CROSSOVER FRQ” (Crossover
Frequency) appears on the display.
The display changes to show the current setting.
2. Turn MULTI JOG to select the
crossover frequency level
according to the size of the small
speaker connected.
• As you turn it, the display changes to show the following:
• Use the following comments as reference when adjusting.
80Hz: Select this when the cone speaker unit built in the
speaker is about 12 cm.
100Hz: Select this when the cone speaker unit built in the
speaker is about 10 cm.
120Hz: Select this when the cone speaker unit built in the
speaker is about 8 cm.
Note:
Crossover frequency setting is not valid for the DVD MULTI playback
mode, 3D-PHONIC mode, and HEADPHONE mode.
80Hz 100Hz 120Hz
0dB 10dB
SETTING
MULTI JOG
OFF MID MAX
MULTI JOG
Low Frequency Effect Attenuator Setting
If the bass sound is distorted while playing back a source using
Dolby Digital, DTS Digital Surround or MPEG Multichannel follow
the procedure below.
On the front panel ONLY:
1. Press SETTING repeatedly until
“LFE ATT” (Low Frequency
EffectAttenuator) appears on the
display.
The display changes to show the current setting.
2. Turn MULTI JOG to select the
low frequency effect attenuator
level.
• As you turn it, the display changes to show the following:
0dB: Normally select this.
10dB: Select this when the bass sound is distorted.
Note:
Low frequency effect attenuator setting is not valid for the DVD MULTI
playback mode.
Dynamic Range Compression Setting
You can compress the dynamic range (difference between maximum
sound and minimum sound) of the reproduced sound. This is useful
when enjoying surround sound at night.
• This function takes effect only when playing back a source using
Dolby Digital.
On the front panel ONLY:
1. Press SETTING repeatedly until
“D. RANGE COMP.” (Dynamic
Range Compression) appears on
the display.
The display changes to show the current setting.
2. Turn MULTI JOG to select the
appropriate item about the
compression level.
• As you turn it, the display changes to show the following:
OFF: Select this when you want to enjoy surround with its
full dynamic range. (No effect applied.)
MID: Select this when you want to reduce the dynamic
range a little. (Factory setting.)
MAX: Select this when you want to apply the compression
effect fully. (Useful at night.)
Note:
Dynamic Range Compression setting is not valid for the DTS Digital
Surround, MPEG Multichannel and DVD MULTI playback mode.
SETTING
MULTI JOG
MULTI JOG
SETTING
EN10_19.RX-7001PGD[U,US]/f 00.5.31, 10:54 AM15

16
English
Digital Input (DIGITAL IN) Terminal
Setting
When you use the digital input terminals, you have to register what
components are connected to which terminals (DIGITAL IN 1/2/3).
Before you start, remember...
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
On the front panel ONLY:
1. Press SETTING repeatedly until
“DIGITAL IN” appears on the
display.
The display changes to show the current setting.
2. Turn MULTI JOG to select the
appropriate digital terminal
setting.
• As you turn it, the display changes to show the following:
1 DVD 2 CD 3 TV (or DBS*) “
1 DVD 2 CD 3 MD “
1 DVD 2 MD 3 TV (or DBS*) “
1 CD 2 DVD 3 TV (or DBS*) “
1 CD 2 DVD 3 MD “
1 CD 2 MD 3 TV (or DBS*) “
1 TV (or DBS*) 2 CD 3 DVD “
1 TV (or DBS*) 2 CD 3 MD “
1 TV (or DBS*) 2 DVD 3 MD “
1 MD 2 CD 3 TV (or DBS*) “
1 MD 2 CD 3 DVD “
1 MD 2 DVD 3 TV (or DBS*) “
(back to the beginning)
*
If you have changed the source name from “TV SOUND” to
“DBS,” “DBS” appears.
Note:
When shipped from the factory, the DIGITAL IN terminals can be used
as the digital input for the following components.
• DIGITAL 1 (coaxial): For DVD player
• DIGITAL 2 (optical): For CD player
• DIGITAL 3 (optical): For digital TV broadcast tuner
Selecting the Analog or Digital Input
Mode
When you have connected some digital source components using the
digital terminals (see page 8), you need to change the input mode for
these components to the appropriate digital input mode correctly —
AUTO/PCM, DOLBY DIGITAL, DTS, or MPEG.
Before you start, remember...
•The digital input (DIGITAL IN) terminal setting should be
correctly done for the sources you want to select the digital
input mode for. Without setting this digital input terminal
correctly, you cannot change the input mode from analog input to
digital input even if you follow the procedure below.
SETTING
MULTI JOG
On the front panel:
1. Turn SOURCE SELECTOR until
the source (CD, MD, TV SOUND,
DBS, or DVD)* for which you
want to change the input mode
appears on the display.
Note:
* Among the sources listed above, you can select the digital input
only for the sources which you have selected the digital input
terminals for.(See “Digital Input (DIGITAL IN) Terminal Setting.”)
2. Press INPUT ANALOG/DIGITAL
repeatedly until the digital input
mode you want appears on the
display.
• Each time you press the button, the input mode changes as
follows:
Normally select “AUTO/PCM,” so the receiver automatically
detects the incoming digital signal format. (The DIGITAL
AUTO indicator lights up on the display.)
– When the receiver can recognize the digital signal format
coming into the receiver, the frame of the digital signal
indicator for the detected signal lights up automatically.
– When the receiver cannot recognize the incoming signal
format correctly, the frame of the digital signal indicator
flashes.
If this happens, select the same digital input mode with the
incoming digital signal — either “DOLBY DIGITAL”, “DTS”
or “MPEG.”
To change the input mode back to analog input, select
“ANALOG.”
From the remote control:
1. Press the source selecting button
(CD, TAPE/MD, TV/DBS, or
DVD)* for which you want to
change the input mode.
Note:
* Among the sources listed above, you can select the digital input
only for the sources which you have selected the digital input
terminals for.(See “Digital Input (DIGITAL IN) Terminal Setting.”)
2. Press ANALOG/DIGITAL to
change the input mode.
• Each time you press the button, the
input mode changes as follows:
Notes:
• Noise may come out of the speakers while searching or skipping a
multi-sound source encoded with Dolby Digital, DTS Digital
Surround or MPEG Multichannel. If this happens, select “DOLBY
DIGITAL” , “DTS” or “MPEG” for digital input mode.
• When you change the source, the digital input mode will be
automatically reset to “AUTO/PCM.”
SOURCE SELECTOR
INPUT
ANALOG/DIGITAL
DVD DVD MUILTI CD TAPE/MD
TV/DBS PHONO FM/AM
VCR
ANALOG/DIGITAL
ANALOG
DTS
AUTO/PCM
DOLBY DIGITAL
(Digital)
(Digital)
(Digital)
MPEG
(Digital)
ANALOG
DTS
AUTO/PCM
DOLBY DIGITAL
(Digital)
(Digital)
(Digital)
MPEG
(Digital)
DIGITAL 2 terminal setting
DIGITAL 3 terminal setting
DIGITAL 1 terminal setting
EN10_19.RX-7001PGD[U,US]/f 00.5.31, 10:54 AM16

17
English
MULTI JOG
NORMAL TEXT
STANDBY
STANDBY/ON
and
TUNER PRESET
STANDBY
STANDBY/ON
and
FM MODE
ONETOUCHOPERATION
SLEEP
2010 30 40 50 60 70 80 90
(Canceled)
00
SETTING
Showing the Text Information on the
Display
When you have connected an MD recorder or CD player equipped
with TEXT COMPU LINK remote control system (see page 36),
you can show the text information, such as disc title or track title, on
the display of this receiver. To show it on the display, follow the
procedure below.
Before you start, remember...
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
On the front panel ONLY:
1. Press SETTING repeatedly until
“FL DISPLAY” appears on the
display.
The display changes to show the current setting.
2. Turn MULTI JOG to select either
the source name or the text
information to be shown on the
display.
• As you turn it, the display changes to show the following:
NORMAL: Source name appears during play.
TEXT: Text information appears during play.
Note:
Though you have selected “TEXT,” the source name such as “CD” or
“MD” appears if a playing disc has no text information.
Setting the AM Tuner Interval Spacing
Some countries space AM stations 9 kHz apart, and other countries
use 10 kHz spacing.
On the front panel ONLY:
To select the 10 kHz interval:
Be sure the receiver is turned off, but is plugged into an AC outlet.
Hold down TUNER PRESET and press STANDBY/ON . Now
the 10 kHz interval is selected.
To change back to the 9 kHz interval:
Be sure the receiver is turned off, but is plugged into an AC outlet.
Hold down FM MODE and press STANDBY/ON . Now the
9 kHz interval is selected.
Storing the Basic Settings and
Adjustments — One Touch Operation
JVC’s One Touch Operation function is used to assign and store
different sound settings for each different playing source. By using
this function, you do not have to change the settings every time you
change the source. The stored settings for the newly selected source
are automatically recalled. The following can be stored for each
source:
• Volume level (see page 11)
• Bass boost (see page 12)
• Input attenuator mode (see page 12)
• Subwoofer output level (see page 12)
• Balance (see page 13)
• SEA modes (see page 20)
• DSP modes
– 3D-PHONIC mode settings (see page 24)
– DAP mode settings (see page 24)
– Surround mode settings (see page 25)
• DVD MULTI playback mode settings (see page 29)
On the front panel ONLY:
To store the sound settings
1. Press ONE TOUCH OPERATION.
The ONE TOUCH OPERATION lamp lights
up, then the previously memorized settings
are recalled.
2. Adjust the sound using the functions listed above.
The newly adjusted settings are memorized.
To recall the sound settings
With the ONE TOUCH OPERATION lamp lit, the settings for the
currently selected source are recalled when the source is selected.
To cancel the One Touch Operation function
Press ONE TOUCH OPERATION so that the lamp goes off.
(Even though the One Touch Operation function is canceled, the
recalled sound effects remain active.)
Notes:
• If the source is FM or AM, you can assign a different setting for
each band.
• The DSP modes and DVD MULTI playback mode cannot be used at
the same time.
Using the Sleep Timer
Using the Sleep Timer, you can fall asleep to music and know the
receiver will turn off by itself rather than play all night.
From the remote control ONLY:
Press SLEEP repeatedly.
The SLEEP indicator lights up on the display, and
the shut-off time changes as follows (in minutes):
When the shut-off time comes
The receiver turns off automatically.
To check or change the time remaining until the shut-off time
Press SLEEP once.
The remaining time until the shut-off time appears in minutes.
• To change the shut-off time, press SLEEP repeatedly.
To cancel the Sleep Timer
Press SLEEP repeatedly until “SLEEP 00min.” appears on the
display. (The SLEEP indicator goes off.)
• Turning off the power also cancels the Sleep Timer.
EN10_19.RX-7001PGD[U,US]/f 00.5.31, 10:55 AM17