Toro Vista 08924 Vista 08924TC User manual

Form No. 3463-243 Rev A
V ista™ Lithium Shuttle V ehicle
Model No. 08924 —Serial No. 400000000 and Up
Model No. 08924TC —Serial No. 400000000 and Up
Model No. 08926 —Serial No. 400000000 and Up
Model No. 08928 —Serial No. 400000000 and Up
Register at www .T oro.com.
Original Instructions (EN)
*3463-243*

This product complies with all relevant European
directives; for details, please see the separate product
specic Declaration of Conformity (DOC) sheet.
W ARNING
CALIFORNIA
Proposition 65 W arning
The power cord on this product contains
lead, a chemical known to the State
of California to cause birth defects
or other reproductive harm. W ash
hands after handling.
Battery posts, terminals, and related
accessories contain lead and lead
compounds, chemicals known to
the State of California to cause
cancer and reproductive harm. W ash
hands after handling.
Use of this product may cause exposure
to chemicals known to the State of
California to cause cancer , birth defects,
or other reproductive harm.
Introduction
This vehicle is intended to be primarily used
of f-highway to transport people. Using this product
for purposes other than its intended use could prove
dangerous to you, your passengers, and bystanders.
Read this information carefully to learn how to operate
and maintain your product properly and to avoid
injury and product damage. Y ou are responsible for
operating the product properly and safely .
V isit www .T oro.com for product safety and operation
training materials, accessory information, help nding
a dealer , or to register your product.
Whenever you need service, genuine T oro parts, or
additional information, contact an Authorized Service
Distributor or T oro Customer Service and have the
model and serial numbers of your product ready .
Figure 1 identies the location of the model and serial
numbers on the product. W rite the numbers in the
space provided.
Important: W ith your mobile device, you can
scan the QR code on the serial number decal (if
equipped) to access warranty , parts, and other
product information.
g405906
Figure 1
1. Model and serial number location
Model No.
Serial No.
This manual uses 2 words to highlight information.
Important calls attention to special mechanical
information and Note emphasizes general information
worthy of special attention.
The safety-alert symbol ( Figure 2 ) appears both in
this manual and on the machine to identify important
safety messages that you must follow to avoid
accidents. This symbol will appear with the word
Danger ,W arning , or Caution .
•Danger indicates an imminently hazardous
situation which, if not avoided, will result in death
or serious injury .
•W arning indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury .
•Caution indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderate injury .
g000502
Figure 2
Safety-alert symbol
© 2023—The T oro® Company
81 1 1 L yndale A venue South
Bloomington, MN 55420
2
Contact us at www .T oro.com.
Printed in the USA
All Rights Reserved

Contents
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
General Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Safety and Instructional Decals . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1 Installing the Steering Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2 Charging the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3 Checking the Fluid Levels and T ire
Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4 Burnishing the Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Attachments/Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Before Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Before Operation Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Checking the T ire Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Breaking in a New Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
During Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
During Operation Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Monitoring the Battery-System Charge
Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Stopping the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
After Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
After Operation Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Hauling the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
T owing the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
T ransporting the Lithium-Ion Batteries . . . . . . . . . . . . . . 22
Understanding the Lithium-Ion Battery
Charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Maintenance Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Recommended Maintenance Schedule(s) . . . . . . . . . . . 25
Daily Maintenance Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Pre-Maintenance Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Preparing the Machine for Maintenance . . . . . . . . . . . . 27
Removing the Seat Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Installing the Seat Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Removing the Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Installing the Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Lifting the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Greasing the Front Wheel Bearings . . . . . . . . . . . . . . . . . . 30
Electrical System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Using the Battery-Disconnect Switch . . . . . . . . . . . . . . . . 33
Servicing the Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Maintaining the Lithium-Ion Batteries . . . . . . . . . . . . . . . . 33
Maintaining the Battery Charger . . . . . . . . . . . . . . . . . . . . . . . 33
Locating the Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Replacing the Headlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Drive System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Maintaining the T ires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Inspecting the Steering and Suspension
Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Adjusting the Wheel Alignment . . . . . . . . . . . . . . . . . . . . . . . . . 35
Checking the T ransaxle-Fluid Level . . . . . . . . . . . . . . . . . . 36
Changing the T ransaxle Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Brake Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Checking the Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Checking the Brake-Fluid Level . . . . . . . . . . . . . . . . . . . . . . . . 37
Replacing the Service and Parking-Brake
Pads .............................................................. 38
Changing the Brake Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
W ashing the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Storage Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Storing the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Battery Storage Requirements . . . . . . . . . . . . . . . . . . . . . . . . . 39
3

Safety
General Safety
•This product is capable of causing personal injury
or death. Always follow all safety instructions to
avoid serious personal injury .
•Improper operation, maintenance, or poor
housekeeping of the machine may cause it to
become unstable; other factors include terrain
conditions, slope, speed, and poor operator
judgment.
•Read and understand the contents of this
Operator ’ s Manual before you start the machine.
Ensure that everyone using this product knows
how to use it and understands the warnings.
•Use your full attention while operating the
machine. Do not engage in any activity that
causes distractions; otherwise, injury or property
damage may occur .
•Do not put your hands or feet near moving
components of the machine.
•Do not operate the machine without all guards
and other safety protective devices in place and
in good working order .
•Keep bystanders and children out of the operating
area. Never allow children to operate the machine.
•Stop and shut of f the machine and remove the key
before servicing.
4

Safety and Instructional Decals
Safety decals and instructions are easily visible to the operator and are located near any area
of potential danger . Replace any decal that is damaged or missing.
decal120-9570
120-9570
1. W arning—stay away from moving parts, keep all guards
and shields in place.
For Model 08926 and 08928 only:
decal140-0920
140-0920
1. W arning—do not operate
the machine while under
the inuence of alcohol or
drugs.
2. Falling hazard;
dismemberment
hazard—passengers
should sit in the
designated seating
positions only; keep
all limbs inside the vehicle.
decal140-0924
140-0924
1. Eco mode
2. Performance mode
decal140-4590
140-4590
1. Read the Operator ’ s Manual for battery information.
decal144-0275
144-0275
1. Batteries are ammable.
decal144-0277
144-0277
1. Positive terminal 4. Do not dispose improperly .
2. Read the Operator ’ s
Manual .
5. Do not expose to re.
3. Recycle the battery .
For Model 08924 and 08924TC only:
decal144-5574
144-5574
1. W arning—do not operate
the machine while under
the inuence of alcohol or
drugs.
2. Falling hazard;
dismemberment
hazard—do not carry
more than 4 occupants;
occupants should sit in
the designated seating
positions only; keep all
limbs inside the vehicle.
5

decal144-5576
144-5576
1. Read the Operator ’ s
Manual for fuse
information.
5. Horn (20 A)
2. USB (5 A) 6. Display (10 A)
3. Headlights (10 A) 7. Main system B+ (10 A)
4. Alarm (5 A) 8. DC to DC (20 A)
decal144-5580
144-5580
1. Read the Operator ’ s
Manual before performing
maintenance.
3. Brake uid
2. T ransmission uid
4. T ire pressure
decal145-7345
145-7345
1. Electrical shock hazard
decal144-5571
144-5571
1. W arning—read the Operator's Manual . 4. Collision hazard—do not operate the machine on public roads.
2. W arning—receive proper training before operating the
machine.
5. T ipping hazard—drive slowly across or up slopes; take turns
slowly; do not exceed speeds of 25 kph (16 mph); drive slowly
when carrying passengers; drive slowly on uneven terrain
3. W arning—never allow children to operate the machine; only
operate the machine while sitting in the operator ’ s position.
6. W arning—Engage the parking brake, turn the key to the O FF
position, and remove the key before leaving the operator ’ s
position.
decal144-5573
144-5573
1. Of f 4. T o start the machine—1) Sit in the operator ’ s position and
have all passengers sit in the designated seating positions; 2)
T urn the key to the O Nposition; 3) Press the direction selector
button to the desired direction of travel; 4) Press down on
the pedal.
2. On 5. T o shut of f the machine—1) Release the pedal; 2) Engage the
parking brake; T urn the key to the O FF position; 4) Remove
the key .
3. Parking brake—Disengage (hold for 5 seconds)
6

decal145-5301
145-5301
1. Negative battery terminal
decal145-5338
145-5338
1. W arning—read the Operator ’ s Manual . 4. Electric shock hazard—do not perform maintenance on the
battery .
2. W arning—do not open the battery; do not use a damaged
battery .
5. Electric shock hazard
3. Explosion hazard—do not expose to sparks or open ame.
7

Setup
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure Description
Qty .
Use
Steering wheel
1
Screw
5
Spring
2
Wheel cover 11
Wheel clip 1
Install the steering wheel (4-passenger
crated model only).
2
No parts required
–
Charge the machine.
3
No parts required
–
Check the uid levels and tire pressure.
4
No parts required
–
Burnish (break-in) the brakes.
1
Installing the Steering
Wheel
4-Passenger Crated Model Only
Parts needed for this procedure:
1
Steering wheel
5
Screw
2
Spring
1 Wheel cover
1 Wheel clip
Procedure
Refer to Figure 3 for this procedure.
1. Place the steering wheel on the steering shaft.
Ensure that the steering wheel is centered
(i.e., the at bottom should be parallel with the
ground).
2. Use the locknut to secure the steering wheel to
the steering shaft.
3. T orque the locknut to 27 N∙m (20 ft-lb).
4. Use 2 screws and 2 springs to secure the wheel
clip to the wheel cover .
5. Use 3 screws to secure the wheel cover to the
steering wheel.
6. T orque the 5 screws to 0.6 N∙m (5 in-lb).
8

g410793
Figure 3
1. Steering shaft
5. Wheel clip
2. Screw
6. Locknut
3. Spring 7. Steering wheel
4. Wheel cover
2
Charging the Machine
No Parts Required
Procedure
Charge the machine; refer to Understanding the
Lithium-Ion Battery Charger ( page 22 ) .
3
Checking the Fluid Levels
and T ire Pressure
No Parts Required
Procedure
1. Check the brake-uid level before you rst start
the machine; refer to Checking the Brake-Fluid
Level ( page 37 ) .
2. Check the transaxle-uid level before you
rst start the machine; refer to Checking the
T ransaxle-Fluid Level ( page 36 ) .
3. Check the air pressure in the tires; refer to
Checking the T ire Pressure ( page 17 ) .
4
Burnishing the Brakes
No Parts Required
Procedure
T o ensure optimum performance of the brake system,
burnish (break-in) the brakes before use.
1. Bring the machine up to full speed, apply the
brakes to rapidly stop the machine without
locking up the tires.
2. Repeat this procedure 10 times, waiting 1 minute
between stops, to avoid overheating the brakes.
9

Product Overview
Controls
Control Panel
g406290
Figure 4
1. Key switch 5. Display
2. Direction selector
6. USB port
3. Light switch 7. Brake pedal
4. Horn switch 8. Accelerator pedal
10