Toro 140-2050 User manual

FormNo.3435-911RevA
FrontWeightKit
Zero-Turn-RadiusRidingMower
ModelNo.140-2050
InstallationInstructions
Installation
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
ProcedureDescriptionQty.Use
1Nopartsrequired–Preparethemachine.
2Nopartsrequired–Removetheguards(machinesequipped
withMyRideonly).
Bolt(3/8x1inch)4
Locknut(3/8inch)6
Leftweight-mountingbracket1
Rightweight-mountingbracket1
Washer2
Bolt(5/8x2-3/4inches)2
3
Suitcaseweight8
Installtheweights.
4Nopartsrequired–Installtheguards(machinesequipped
withMyRideonly).
1
PreparingtheMachine
NoPartsRequired
Procedure
1.Parkthemachineonalevelsurface.
2.Disengagetheblade-controlswitch.
3.Movethemotion-controlleversoutwardtothe
NEUTRAL-LOCKpositiontoengagetheparking
brake.
4.Shutofftheengineandremovethekey.
©2019—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.Toro.com.OriginalInstructions(EN)
PrintedintheUSA
AllRightsReserved*3435-911*A

2
RemovingtheGuards
MachinesEquippedwithMyRide®
Only
NoPartsRequired
Procedure
Note:Retainallremovedpartsforlaterinstallation.
1.Removetheboltssecuringtheguardsonthe
sidesoftheframe.
2.Removetheguardsonbothsidesoftheframe
(Figure1).
g308507
Figure1
3
InstallingtheWeights
Partsneededforthisprocedure:
4Bolt(3/8x1inch)
6Locknut(3/8inch)
1Leftweight-mountingbracket
1Rightweight-mountingbracket
2Washer
2Bolt(5/8x2-3/4inches)
8Suitcaseweight
Procedure
CAUTION
Thebaggerchangestheweightdistributionof
themachine.Operatingthemachinewithout
thefrontweightsmaycauseanunstable
condition,whichcouldresultinalossof
control.
Ensurethefrontweightsareproperlyinstalled
beforeoperatingthemachinewiththebagger
attachment.
1.Installtheweight-mountingbracketstotheunder
sideoftheframeusing2bolts(3/8x1inch),
and2locknuts(3/8inch)asshowninFigure2.
2.Installsuitcaseweightstotheweightmounting
bracketsusing2bolts(5/8x2-3/4inches),2
washers,and2locknuts(3/8inch)asfollows:
•Ifyourmachinehasa42-inchstampeddeck,
install8suitcaseweights.
•Ifyourmachinehasanyothercuttingdeck,
install6suitcaseweights(Figure3).
3.Onceyouhaveinstalledalltheweightsand
brackets,ensurethatallthefastenersaretight.
Tightenasnecessary.
Important:Wheneveryouremovethe
baggerattachment,remembertoremovethe
frontweightstoreturntheproperstability
tothemachine.
2

g299192
Figure2
Castorforkandwheelnotshownforclarity.
1.Frontrightcaster4.Rightmountingbracket
2.Forwardhole(rightside
shown)
5.Bolts(3/8x1inch)
3.Locknut(3/8inch)
g299244
Figure3
1.Spacer3.Suitcaseweights
2.Locknut(3/8inch)4.Bolts(5/8x2-3/4inches)
4
InstallingtheGuards
MachinesEquippedwithMyRide
Only
NoPartsRequired
Procedure
1.Insertthetopoftheguardunderthedeck;tiltthe
guardsothatitslidesundertheframeandtthe
guardintothenotches(Figure4).
g308505
g308526
Figure4
1.Notch
2.Securetheguardstotheframeusingthebolts
removedin2RemovingtheGuards(page2)
asshowninFigure1.
3