Toro TimeCutter HD ZX5400 Manual

FormNo.3410-234RevC
TimeCutter®HDRidingMower
ForAllTimeCutter®HDRidingMowers
Setup
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
ProcedureDescriptionQty.Use
1Nopartsrequired–Connectthebattery.
Rearhitch1
Bolt(5/16x1inch)2
2Locknut(5/16inch)2
Installtherearhitch.
3Nopartsrequired–Setupthemotion-controllevers(CE
machinesonly).
4Nopartsrequired–Checkthemoweradjustment.
Ignitionkey1
Hosecoupling(non-CEmachinesonly)1
Operator'sManual1
Engineowner’smanual(non-Toro
enginesonly)1
5
Operatortrainingmaterial1
Completethesetup.
Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.
©2018—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.Toro.com.OriginalInstructions(EN)
PrintedintheUSA
AllRightsReserved*3410-234*C

1
ConnectingtheBattery
NoPartsRequired
Procedure
1.Loosenthe2fastenersonthebatterycover
counterclockwise1/4turnandremovethe
batterycover(Figure1).
g190587
Figure1
2.Removetheplasticcapfromthenegative
batterypost.
3.Removethefastenersonthenegativebattery
cable,andusethemtosecurethenegative
batterycabletothenegativebatterypost(Figure
2).
g197768
Figure2
1.Hexbolt4.Negativebatterypostcap
2.Washer5.Nut
3.Negativebatterycable6.Negativebatterypost
2

2
InstallingtheRearHitch
Partsneededforthisprocedure:
1Rearhitch
2Bolt(5/16x1inch)
2Locknut(5/16inch)
Procedure
InstallthebrackettotheframeasshowninFigure
3andFigure4.
g191160
Figure3
Beforeassembly
1.Bolt3.Locknut
2.Bracket
g191159
Figure4
Afterassembly
3
SettingUpthe
Motion-ControlLevers
CEMachinesOnly
NoPartsRequired
Procedure
1.Locatethemotion-controlleversattached,but
foldeddownonthemachine.
2.Removetheupperbolt(3/8x1inch)and
washer;loosenthelowerbolt(3/8x1inch).
3.Raisethemotioncontrolleverstotheupright
position.
4.Aligntheholesinthemotion-controlleverwith
theholesinthecontrol-armshaft,andinstallthe
boltandwasherremovedpreviously.Repeat
thisforbothcontrolslevers.
Note:Handtightenallfasteners.
5.Movethemotion-controlleverstothepark
position,raisetheseat,andmovethecontrol
leversbacktothecenterposition(neutral).
6.Verifythatthemotion-controlleversareproperly
aligned.
Note:Adjustasnecessary.Tightenall
fasteners.
4
CheckingtheMower
Adjustment
NoPartsRequired
Procedure
Adjusttheside-to-sidelevelandthefront-to-rearblade
slope.UsetherelevantproceduresintheOperator's
Manualtoverifythatthedeckislevel,andmakeany
adjustmentsasnecessary.RefertotheOperator's
Manualformoreinformation.
3

5
CompletingtheSetup
Partsneededforthisprocedure:
1Ignitionkey
1Hosecoupling(non-CEmachinesonly)
1Operator'sManual
1Engineowner’smanual(non-Toroenginesonly)
1Operatortrainingmaterial
CheckingtheTirePressure
Checkthefrontandreartiresforproperination;
refertoCheckingtheTirePressureintheOperator’s
Manualfortherecommendedinationpressure.
CheckingtheSide-Discharge
Chute
Removethepackingrestraintholdingthe
side-dischargechuteupandlowerthechuteinto
place.
CheckingtheEngine-OilLevel
Beforeyoustarttheengineandusethemachine,
checktheoillevelintheenginecrankcase;referto
CheckingtheOilLevelintheOperator'sManual.
CheckingtheAirCleaner
Ensurethattheaircleanerisproperlyinstalledinthe
engineair-cleanerbox.
OrganizingtheMaterial
Keepallthefollowingitemswiththemachine:
•Ignitionkey
•Hosecoupling(non-CEmachinesonly)
•Operator'sManual
•Engineowners’smanual(non-T oroenginesonly)
•Viewtheoperatortrainingmaterialbefore
operatingthemachine.
4