Toshiba HAORI RAS-B10E2KVRG-A User manual

OWNER’S MANUAL
AIR CONDITIONER (SPLIT TYPE)
For general public use
Indoor unit
RAS-B10, B13, B16E2KVRG-A
Outdoor unit
RAS-10, 13, 16E2AVRG-A
1129850210
ENGLISH

PRECAUTIONS FOR SAFETY
Read the precautions in
this manual carefully before
operating the unit.
This appliance is lled with R32.
■Warning indications on the air conditioner unit
Warning indication Description
CAUTION
BURST HAZARD
Open the service valves
before the operation,
otherwise there might be
the burst.
CAUTION
BURST HAZARD
Open the service valves before the operation,
otherwise there might be the burst.
● Keep this manual where the operator can easily nd it.
● Read the precautions in this manual carefully before operating the unit.
● This appliance is intended to be used by expert or trained users in shops, in light
industry and on farms, or for commercial use by lay persons.
● The precautions described herein are classied as DANGER, WARNING and
CAUTION. They both contain important information regarding safety. Be sure to
observe all precautions without fail.
DANGER
● Do not install, repair, open or remove the cover. It may expose you to
dangerous voltages. Ask the dealer or the specialist to do this.
● Turning o󰀨 the power supply will not prevent potential electric shock.
● The appliance shall be installed in accordance with national wiring regulation.
● Means for disconnection from the supply having a contact separation of at least
3 mm in all poles must be incorporated in the xed wiring.
● The appliance must be stored in a room without continuously operating ignition
sources (for example, open ames, an operating gas appliance or an operating
electric heater).
● In order to avoid re, explosion or injury, do not operate the unit when harmful
gases (e.g. ammable or corrosive) are detected near the unit.
WARNING
● Do not expose your body directly to cool or warm air for a long time.
● Do not insert your nger or any article into the air inlet/outlet.
● When an abnormality (burning smell, etc.) occurs, stop the air conditioner and
disconnect the power supply or turn o󰀨 the breaker.
● This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.

PRECAUTIONS FOR SAFETY
● This appliance is not intended for use by person (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
● The air conditioner must be installed, maintained, repaired and removed by a
qualied installer or qualied service person. When any of these jobs is to be
done, ask a qualied installer or qualied service person to do them for you.
● Children should be supervised to ensure that they do not play with the
appliance.
● Do not use any refrigerant di󰀨erent from the one specied (R32) for
complement or replacement. Otherwise, abnormally high pressure may be
generated in the refrigeration cycle, which may result in a failure or explosion of
the product or an injury to your body.
● Do not use means to accelerate the defrosting process or to clean, other than
those recommended by the manufacturer.
● The appliance shall be stored in a room without continuously operating ignition
sources (for example: open ames, an operating gas appliance or an operating
electric heater).
● Be aware that refrigerants may not contain an odour.
● Do not pierce or burn as the appliance is pressurized. Do not expose the
appliance to heat, ames, sparks, or other sources or ignition. Else, it may
explode and cause injury or death.
CAUTION
● Do not wash the unit with water. It may cause an electric shock.
● Do not use this air conditioner for other purposes such as preserving food,
breeding animal, etc.
● Do not step or put anything on the indoor/outdoor unit. It may cause an injury or
damage the unit.
● Do not touch aluminium n because it may cause an injury.
● Before cleaning the unit, turn o󰀨 the main switch or the circuit breaker.
● When the unit won’t be used for a long time, turn o󰀨 the main switch or the
circuit breaker.
● It is recommended that maintenance be performed by a specialist when the unit
has been operated for a long time.
● The manufacturer shall not assume any liability for the damage caused by not
observing the description of this manual.
● Remote controller and Holder are contained with magnet please keep far from
product that e󰀨ect with magnet (such as electronics appliance magnetic strip
card and etc.)
● High temperature, high magnet eld and direct force collisions may e󰀨ect to
magnet force down.

INDOOR UNIT DISPLAY
PREPARATION BEFORE USE
AIR FLOW DIRECTION
REMOTE CONTROL
COOLING / FAN ONLY OPERATION
AUTOMATIC OPERATION
HEATING and 8°C OPERATION
DRY OPERATION
1
2
3
4
5
6
7
8
2
345
11 ECO (White)
2 Wi-Fi access (White)
3 PURE (White)
4 Timer (White)
5 Operation Mode
- Cool (Blue)
- Heat (Orange)
1Infrared signal emitter
2 Start/Stop button
3 Mode select button
4Temperature button
5 Fan speed button
6 Menu select button
7 Set louver Up-Down button
8 Set louver Left-Right button
9 Check button*
*Check button under battery cover
● Display brightness can be adjusted, follow procedure on !.
Preparing Filters
1. Open the air inlet grille and remove the air lters.
2. Attach the lters. (see detail in the Installation Manual).
Loading Batteries (when use wireless operation.)
1. Remove the slide cover.
2. Insert 2 new batteries (AAA type)
following the (+) and (–) positions.
Remote Control Reset
1. Remove the batteries.
2. Press .
3. Insert the batteries.
1. Press : Select Cool , or Fan only .
2. Press : Set the desired temperature. Min. 17°C, Max. 30°C.
Fan Only: No temperature indication
3. Press : Select AUTO, LOW , LOW+ , MED ,
MED+ , HIGH or Quiet
To automatically select cooling, heating, or fan only operation
1. Press : Select Auto A.
2. Press : Set the desired temperature. Min. 17°C, Max. 30°C.
3. Press : Select AUTO, LOW , LOW+ , MED ,
MED+ , HIGH or Quiet
1. Press : Select Heat .
2. Press : Set the desired temperature. Min = 5°C, Max = 30°C.
* Temperature range 5-16°C is Heat mode with 8°C operation with less of
energy usage
3. Press : Select AUTO, LOW , LOW+ , MED ,
MED+ , HIGH or Quiet
Note: During 8°C mode active (temperature range 5-16°C), some operation
such as QUIET, Hi POWER, TIMER OFF cannot use.
For dehumidication, a moderate cooling performance is controlled
automatically.
1. Press : Select Dry .
2. Press : Set the desired temperature. Min. 17°C, Max. 30°C.
Note: DRY mode fan speed is set to Auto only.
1
Press : Move the
louver in the desired vertical
direction.
2
Press : Move the
louver in the desired horizontal
direction.
3
SWING operation can be
selected from MENU button
Swing o󰀨
Vertical
(Up-Down)
Swing
Horizontal
(Left-Right)
Swing
Vertical and
Horizontal
Swing
HADA CARE
FLOW
H.DA
● Vertical (Up-Down) swing
● Horizontal (Left-Right) swing
● HADA Care ow
Note:
● Do not move the louver manually by hands or others.
●The louver may automation positioning by some operation mode.
9
1
2
3
5
7
4
6
8

Comfortable air ow can select from feature.
Louver swing operation:
● To distribute air ow in both vertical and horizontal by swing the louver
automatically.
HADA care ow operation:
● Air ow upward to the ceiling, provide Indirect air ow to body and
homogenize room temperature.
Note:
● During HADA CARE FLOW mode, FIX button cannot active.
Louver Swing and HADA Care Flow Operation Setting
1. Press MENU button for enter menu selection
Blink
During triangle mark blink can select menu by press TEMP. button.
2. Enter Louver set by press MENU button again.
triangle mark will stop blink and setting feature will be blink instead.
Blink
3. Select Louver swing or HADA CARE FLOW by press TEMP. button.
Swing
o󰀨
HADA CARE FLOW
H.DA
Vertical and
Horizontal
Swing
Vertical
(Up-Down)
Swing
Horizontal
(Left-Right)
Swing
4. Conrm selected feature by press MENU button again.
When feature had selected will return to menu selection display triangle mark
will blink .
5. Leave from menu setting display by select exit and press menu button
Leave from menu setting to normal display (no triangle and feature blink).
MENU SETUP
9
For select more setting of Air conditioner such as Louver select ,Hi Power,
OFF Timer and other use MENU button
9.1 LOUVER SWING and HADA CARE FLOW OPERATION
FIX
MODE
FANM ENU
FIX
FIX
FIX
FAN
MEN
MOD

Keep outdoor unit operating silently to ensure either yourself or neighborhood
will have a tight sleep in nighttime. By this feature, the heating capacity will
be optimized to deliver such silent experience. The silent operation can be
selected from one of two purposes (Silent 1 and Silent 2).
There are three setting parameters: Standard level > Silent 1 > Silent 2
Silent 1:
● Though operating silently, the Heating (or Cooling) capacity is still prioritized
to ensure having su󰀩cient comfort inside the room.
● This setting is a perfect balance between the Heating (or Cooling) capacity
and the Sound level of outdoor unit.
Silent 2:
●Compromising the Heating (or Cooling) capacity to the Sound level in any
circumstance where the outdoor unit’s sound level is highly prioritized.
● This setting has a purpose to reduce the maximum sound level of outdoor
unit by 4 dB(A).
Note:
● While activating of Silent operation, inadequate heating (or cooling) capacity
may occur.
Silent Operation Setting
1. Press MENU button for enter menu selection
Blink
During triangle mark blink can select menu by press TEMP. button.
Blink both triangle and
feature mark Feature not
yet set
2. Enter SILENT set by press MENU button.
triangle mark will stop blink and setting feature will be blink instead.
3. Select SILENT operation by press TEMP. button.
SILENT#1 SILENT#2 None
4. Conrm selected feature by press MENU button again.
Blink only triangle
Feature already set
When feature had selected will return to menu selection display triangle mark
will blink
5. Leave from menu setting display by select EXIT.
To automatically control room temperature and airow for faster cooling or
heating operation (except in DRY and FAN ONLY mode)
1. Press MENU button for enter menu setting and press TEMP. button to
select Hi POWER
Blink both triangle and
feature mark Feature not
yet set
2. Conrm selected feature by press MENU button again.
Blink only triangle Feature
already set
3. Leave from menu setting display by select EXIT.
To automatically control room temperature to save energy
(except in DRY and FAN ONLY mode)
1. Press MENU button for enter menu setting and press TEMP. button to
select ECO
Blink both triangle and
feature mark Feature not
yet set
2. Conrm selected feature by press MENU button again.
Blink onlyltriangle Feature
already set
3. Leave from menu setting display by select EXIT.
Note:
● Cooling operation; the set temperture will increase automatically
1 degree/hour for 2 hours (maximum 2 degrees increase).
For heating operation the set temperature will decrease.
9.2 SILENT OPERATION (Outdoor Unit) 9.3 Hi POWER OPERATION Hi-P
9.4 ECO OPERATION ECO

Keep indoor unit’s fan blowing continuously during thermo o󰀨, to circulate
heat from other sources over the room. There are three setting parameters:
Default setting > Fireplace 1 > Fireplace 2
Fireplace 1:
● During thermo o󰀨 period, the indoor unit’s fan will continue to run by the
same speed, previously selected by end-user.
Fireplace 2:
● During thermo o󰀨 period, the indoor unit’s fan will continue to run at
super-low speed, programmed from factory.
Fireplace Operation Setting
1. Press MENU button for enter menu setting and press TEMP. button to
select FIREPLACE
Blink both triangle and
feature mark Feature not
yet set
2. Enter FIREPLACE set by press MENU button.
triangle mark will stop blink and setting feature will be blink instead.
3. Select FIREPLACE operation by press TEMP. button.
FIREPLACE 1 FIREPLACE 2 None
4. Conrm selected feature by press MENU button again.
Blink only triangle Feature
already set
When feature had selected will return to menu selection display triangle mark
will blink
5. Leave from menu setting display by select EXIT.
Note:
● While Fireplace operation on heating mode, indoor unit fan always runs and
cold air breezing might be occurred.
● Fireplace will operate in Heating mode only.
To set the timer OFF when the air conditioner is operating.
1. Press MENU button for enter menu setting and press TEMP. button to
select TIMER OFF.
Blink both triangle and
feature mark Feature not
yet set
2. Enter TIMER set by press MENU button.
triangle mark will stop blink and setting feature will be blink instead.
3. Select TIMER OFF by press TEMP. button.
Can select TIMER OFF from 0.5 - 12hrs.
4. Conrm TIMER OFF by press MENU button.
Blink only triangle
Feature already set
5. Leave from menu setting display by select EXIT.
Note:
● The setting will be saved for the next same operation.
Cancel TIMER OFF
6. During TIMER OFF already set (no.5) press MENU button and press
TEMP. button to select TIMER OFF.
Blink only triangle
Feature already set
7. Press MENU button again will cancel TIMER OFF.
Blink both triangle and feature
mark Feature not yet set
8. Leave from menu setting display by select EXIT.
9.5 FIREPLACE OPERATION 9.6 TIMER OFF OPERATION

9.8 POWER-SELECTION OPERATION
Capture e󰀩ciency of oating impurities in the air is accelerated by plasma ion
contaminates such as bacteria, odor, smoke, dust and virus are caught and
deactivated by Plasma Ion.
1. Press MENU button for enter menu setting and press TEMP. button to
select PURE
Blink both triangle and
feature mark Feature not
yet set
2. Conrm selected feature by press MENU button again.
Blink only triangle Feature
already set
3. Leave from menu setting display by select EXIT.
Note:
● Plasma Ion operation dose not remove harmful substances from cigarette
smoke (carbon monoxide etc.). Open a window occasionally for ventilation.
This function is used when the circuit breaker is shared with other electrical
appliances. It limits the maximum current and power consumption to 100%,
75%, or 50% and can be implemented by POWER-SELECTION. The lower
percentage, the higher saving and also longer compressor lifetime.
Notes :
● Due to the reason that POWER-SELECTION function limits the maximum
current, inadequate cooling or heating capacity may occur.
1. Press MENU button for enter menu setting and press TEMP. button to select
POWER-SEL
Blink only triangle
2. Enter POWER-SEL setting by press MENU button again.
3. Select POWER-SEL level by press TEMP. button.
100% 75% 50%
4. Conrm POWER-SEL level by press MENU button.
5. Leave from menu setting display by select EXIT.
MENU
MEN
˚C
To defrosting the heat exchanger of the outdoor unit during Heating operation
Press and hold MENU
MEN
: for 5 seconds , then remote control display will
show as picture 1 for 2 seconds.
This product is designed so that, after a power failure, it can restart
automatically in the same operating mode as before the power failure.
Information
The product is shipped with Auto Restart function in the ON position.
Turn it OFF if this function is not required.
How to turn OFF the Auto Restart Function
● Press and hold the [OPERATION] button on the indoor unit for 3 seconds
(3 beep sounds but OPERATION lamp does not blink).
How to turn ON the Auto Restart Function
● Press and hold the [OPERATION] button on the indoor unit for 3 seconds
(3 beep sounds and OPERATION lamp blink 5 time/sec for 5 seconds).
Notes :
● In case of ON timer or OFF timer are set, AUTO RESTART OPERATION
does not activate.
● Default setting of AUTO RESTART OPERATION is ON.
To decrease the display lamp brightness or turn it o󰀨.
1. Press and hold FAN
FAN
for 3 seconds until brightness level ( , ,
or ) is shown on remote control LCD then release the button.
2. Press Rise or
Decrease
to adjust brightness in 4 levels.
Remote control
LCD Operation display Brightness
Lamp illuminates full brightness.
100%
Lamp illuminates 50% brightness.
50%
Lamp illuminates 50% brightness and the
operation lamp is turned o󰀨.
50%
All lamps are turned o󰀨.
All turned o󰀨
● In the examples of and , the lamp illuminated for 5 seconds before going o󰀨.
9.7 PLASMA ION OPERATION
PURE
MANUAL DEFORST OPERATION
AUTO RESTART FUNCTION SETTING
10
12
1
DISPLAY LAMP BRIGHTNESS ADJUSTMENT
11

In case of the misplaced or discharged remote control
● Pressing the RESET button, the unit can start
or stop without using the remote control.
● Operation mode is set on AUTOMATIC
operation, preset temperature is 24°C and fan
operation is automatic speed.
Firstly, turn o󰀨 the circuit breaker.
Indoor Unit and Remote Control
● Clean the indoor unit and the remote control with a wet cloth when needed.
● No benzine, thinner, polishing powder or chemically-treated duster.
Air lters
Clean every 2 weeks.
1. Open the air inlet grille.
2. Remove the air lters.
3. Vacuum or wash and then dry them.
4. Reinstall the air lters and close the air inlet grille.
To separate using of remote control for each indoor unit in case of
2 air conditioners are installed nearly.
Remote Control B Setup.
1. Press RESET button on the indoor unit to turn the air conditioner ON.
2. Point the remote control at the indoor unit.
3. Push and hold button on the back side of Remote Control “00” will be
shown on the display. (Picture 1)
4. Press during pushing . “B” will show on the display and
“00” will disappear and the air conditioner will turn OFF. The Remote
Control B is memorized. (Picture 2)
Note: 1. Repeat above step to reset Remote Control to be A.
2. Remote Control A has not “A” display.
3. Default setting of Remote Control from factory is A.
1. Three-minute protection feature: To prevent the unit from being activated
for 3 minutes when suddenly restarted or switched to ON.
2. Preheating operation: Warm up the unit for 5 minutes before the heating
operation starts.
3. Warm air control: When the room temperature reaches the set temperature,
the fan speed is automatically reduced and the outdoor unit will stop.
4. Automatic defrosting: Fans will stop during defrost operation.
5. Heating capacity: Heat is absorbed from outdoors and released into
the room. When the outdoor temperature is too low, use another
recommended heating apparatus in combination with the air conditioner.
6. Consideration for accumulated snow: Select the position for outdoor unit
where it will not be subjected to snow drifts, accumulation of leaves or
other seasonal debris.
7. Some minor cracking sound may occur when unit operating. This is normal
because the cracking sound may be caused by expansion/contraction of plastic.
Note: Item 2 to 6 for Heating model
Air conditioner operating conditions
Temp.
Operation
Outdoor Temperature Room Temperature
Heating ‒15°C ~ 24°CLess than 28°C
Cooling ‒15°C ~ 46°C21°C ~ 32°C
Dry ‒15°C ~ 46°C17°C ~ 32°C
TEMPORARY OPERATION
MAINTENANCE
14
17
OPERATION / RESET Button
REMOTE CONTROL A-B SELECTION
OPERATION AND PERFORMANCE
15
16
21
TROUBLESHOOTING (CHECK POINT)
18
The unit does not operate. Cooling or Heating is abnormally low.
● The power main switch is
turned o󰀨.
● The circuit breaker is activated
to cut o󰀨 the power supply.
●Stoppage of electric current
●ON timer is set.
● The lters are blocked with dust.
●
The temperature has been set improperly.
● The windows or doors are opened.
●The air inlet or outlet of the outdoor
unit is blocked.
● The fan speed is too low.
● The operation mode is FAN or DRY.
● POWER SELECTION function is
set 75% or 50% (This function is
depend on remote controller).
To protect bad smell caused by the humidity in the indoor unit.
1. If the button is pressed once during “Cool” or “Dry” mode,
the fan will continue to run for other 30 minutes, then it will turn o󰀨
automatically. This will reduce the moisture in the indoor unit.
2. To stop the unit immediately, press the more 2 times within 30
seconds.
SELF CLEANING OPERATION
(COOL AND DRY OPERATION ONLY)
13

WIRELESS LAN CONNECTION
19
Toshiba Home AC Control Toshiba Home AC Control application support
Register process
About Toshiba Home AC Control
Please visit the application store on your device to download and install
Toshiba Home AC Control application. iOS : 9.0 or later.
Android : Version 5.0 or later.
Open an application and follow register for User registration.
1Tab Register
5 Enter password by 6-10
characters, combination of
alphabet and number
6 Check for term and condition 7 Conrm information 8 Information will be submitted
to email, click link to conrm
2Enter email address 3Select country 4Enter user name
1. Toshiba Home AC Control can control AC operation by Smartphone or
tablet (mobile device) via internet connection.
2. Everywhere control, control software run on Cloud system and mobile
device can set and monitor AC operation via internet connection.
3. Everyone can control, 1 Wireless adapter maximum 5 User
(use 1 email register).
4. Multi AC system control, 1 user can control 10 AC.
5. Group control.
5.1 Can create and control 3 groups of AC.
5.2 Can control max 10 AC per group.
Note:
1. Adapter can register only 1 email address, if register with new email, current email will be invalid.
2.1 email address can use for register 5 devices for control same AC.
Application
Keyword : Toshiba Home AC Control

Book_01_1129850201-1_EN.indd 11 25/1/2564 BE 14:21
Login to Toshiba Home AC Control application.
Add Wireless adapter for control by Toshiba Home AC Control application.
1 Connect Wireless adapter to A/C and turn on power supply.
2Open application and select Log in.
1 Select “Add AC (Adapter)” from both display above.
*Note
1.In case of Wi-Fi router change or Email for register change need to re-process for add Wireless adapter again
(Build in type : Press MODE button at Remote controller 5 seconds for active AP mode).
2.In case of change Wireless adapter to use with other A/C need to factory reset and re-process for add Wireless adapter again
(Build in type : Press MODE button at Remote controller 5 seconds and select “rb”).
2 Select AC (adapter) connection method.
3Enter user name and
password.
4Login successful.
Build-in type , Wireless adapter already install with unit.
Wireless adapter Build-in
Active Wireless adapter by
remote controller and Auto log in.
Wireless adapter type A
Need to input SSID and Password
of Wireless adapter for log in.
Wireless adapter type B
Wireless adapter auto log in.
Wireless adapter type C
Wireless adapter auto log in.

Wi-Fi Router Name
Wi-Fi Router Password
FIX
MODE
FAN MENU
FIX
FIX
MEN
MOD
X
OD
A
AN
FA
A
FIX
FIX
FIX
FI
FA
FA
FAN
A
MO
Add Wireless adapter for control by Toshiba Home AC Control application.
3 AC (adapter) connect
6 A/C add nished
7Connect successfully
Wireless LED lamp stop blink.
5 Connect with Home Wi-Fi Router
4 Active Wireless adapter by Remote controller
Press and hold
MODE button 5 seconds
Wireless LED mark will blink
when AP mode active
WPS mode
Manual input

Toshiba Home AC Control application
Home screen
Menu
All AC On/O󰀨
Group AC On/O󰀨
Each AC On/O󰀨
Group name
AC device is o󰀪ine
Notication ERROR code
description (pop up)
Add AC
Sub menu all AC
▪Add Group
▪ Delete Group
▪ Operation Setting
Sub menu group
▪ Select AC
▪ Change group name
▪ Group operation Setting
Sub menu AC
▪ Operation Setting
▪ Change name
▪ Delete AC
Setting temperature /
Actual room temp
Current operation mode
of each AC
Weekly schedule Setting
Link to service center
(available in some countvies)

Mode and Condition setting.
Mode select for Toshiba Hame AC Control application.
Enter operation mode of All AC
Enter operation mode of Group AC
Enter operation mode of each AC
Provide for 5 operation modes
Auto
Heat Fan only Off
Cool Dry

Setting in operation mode.
Mode select
OFF-ON timer set 0.5-12hrs.
ON timer set from
Off mode only
Off mode
Tab for select AC
Weekly schedule
OFF-ON Timer set
Temperature set
Indoor temperature
Outdoor temperature
Fan speed set
Louver set
Special feature

MODE
MOD
M
Please make sure Factory Reset is
performed before deleting AC from mobile
application.
(See owner manual ʺPress and hold MODE
button on remote control for 5 second and
active dL functionʺ)
Group operation.
Maximum 3 groups
1 Group maximum = 10 units.
Add group
Add AC in group
Delete AC in group

Weekly schedule set.
Weekly schedule cancel.
Day select Monday - Sunday
Weekly schedule of all AC unit
Time select Mode selectWeekly schedule set for each unit
Select program for active by tick at select box
Weekly schedule
not set
Weekly schedule
set but not active
Weekly schedule
set and active
Weekly schedule of all AC unit

Energy monitoring
Select Room for Energy monitoring
1Select Energy monitoring 2Energy monitoring display
Set cost calculate and currency
Select Energy monitoring display
Export data and send by Email
● The power consumption displayed is just an estimate as it is calculated simply.
It may sometimes di󰀨er from the result measured by the power meter.

In case of have some problem can check from Help menu.
Note :
● The Wireless Adapter must be installed, maintained, repaired and removed by a qualied installer or qualied service
person.
● Contact dealer and/or service center when equipment is malfunction.
DECORATIVE FABRIC INSTALLATION
20
The decorative fabric for cover on the air inlet grille of indoor unit was put in
the accessories. User can use it as required.
The method of installation is as follows.
1. Remove the air inlet grille.
Open the air inlet grille upward and pull it toward you.
As shown on gure as below.
Air inlet grille
2. Prepare the fabric that you choose for install.
3. Insert the fabric into the left and right side of the air inlet grille.
Attach the hook and loop of velcro tape fully together.
As shown on gure as below.
Velcro loop
Velcro hook
Fabric Decorative fabric
4. Insert the fabric into the top and bottom side of the air inlet grille.
Attach the hook and loop of velcro tape fully together.
As shown on gure as below.
Velcro loop Velcro Hook
Fabric
5. Reassembly the air inlet grille by reverse process of 1.
Note:
● The tightness of the fabric depends on attaching the hook and loop of
velcro around the air inlet grille, take appropriate action.
Maintenance & Shelf-life
● Clean when dust stuck or covers the decorative fabric.
● Take extra care when cleaning the decorative fabric.
● Vacuum the decorative fabric with soft brush nozzle that use for
cleaning on furniture or curtain.
Vacuum cleaner
● In case of getting heavy dirty on decorative fabric, please use dry
cleaning service or wash by hand with warm water separated from
other clothes (to avoid color staining), then line dry in the shade.
Note:
● Switch ‘‘OFF’’ and unplug the air conditioner before removing the
air inlet grille and decorative fabric.
● Ensure decorative fabric are completely dry before retting to the
air inlet grille.
● Do not put the decorative fabric in a dishwasher, washing machine,
tumble dryer, oven, microwave or near an open ame.
CAUTION
● If clean decorative fabric by washing, it may a󰀨ect to appearance and
tting of the decorative fabric.
● Recommend to use vacuum cleaner to removing the dusts from
decorative fabric.

MEMO