Toslon TF500 User manual

1
7
7
4
5
Display
1
2
3
6
1) Transmitter 2) Antenna for display
3) Power cable 4) Bttery holder 5) Antenna
extended cable 6) Antenna for transmitter
7) Valcro
Transmitter
1 2
3
1) Transducer 2) Knobs 3) Rubber
Note: the rubber is dierent according to
dierent bait boats
Transducer
Check the content
(Optional) (Optional)

Installation (transducer)
2
1) For general boats, like Carp
Madness, Anatec Monocoque,
you need need to drill a hole on
the boat bottom to x the
transducer.
2) For boats of Carplounge/-
Waveruner/ Vegaboat/Carpboat
etc, there is a transducer groove
on the bottom. So, you only need
to simply match the
transducer to
the boat
with a
rubber.
3) For Anatec catamaran bait
boat, there is a transducer
groove on the bottom. So, you
only need simply match the
transducer to the
boat with
a rubber.
r to t
h
e

3
1) Drill an hole (5mm diameter)
on the selected position.
2) Screw down the wisher and
nut from the antenna
extended , then hold the DC
cable through the hole from
inner housing, and Screw
tighted the nut by an wrench.
3) Screw the antenna on boat
antenna_extended cable
connect to battery connect to transducer
signal indicator
connect to antenna
with antenna_extended
cable
antenna for transmitter
Antenna Installation
After all the installatiion are
nished, please connect the
parts (transducer, antenna,
battery) to the transmiter.
Then x the transmitter inner
the boat.
Wiring
Installation (antenna & wiring)

4
Powering
Battery Type
12V Lead-acid
8*AA NiMH
8*AA Alkaline
2S Lithium
3S Lithium
4S Lithium
Voltage
10.8v~14.8V
7.8V~10.6V
7.5V~12.8V
5.6~8.4V
8.4~12.6V
11.2V~16.8V
Permission
12V
lead-acid
8AA
NiMH
8AA
Alkaline
2S
Lithium
3S
Lithium
4S
Lithium
Recomended voltage
Absolute Maximum voltage
For display
6-12V
14.8V
For transmitter
6-12V
14.8V
Note: overvoltage may burn the elements in the device!
From bellow shows the voltage range of the most popular batteries in the market:

Using Instruction
5
1) Please do not put the display on ground during the operation,
which could cause a short R/C distance.
The proper way is using an tripod to support the display, and
keep it at least 1.2m above the ground.
2) Make sure the antenna is tighten on the boat, otherwise the
R/C distance will be greatly shorten.

Key function
Menu Open Menu settings; Switch between menus
Up arrow Move up to select menu; increase a value of option
Down arrow Move down to select menu; decrease a value of option
Power & Exit Turns unit on/o. Also be use to quit a menu setting
Ent Finalizes menu selections; conrm a setting
6
Note: during the unit working, you can press the UP arrow to“freeze” the screen.
Press any key will unfreeze the screen.

What’s on the display
7
Depth readout
Water temperature
Voltage of transmitter
Voltage of display
bottom
signal indicator Depth range
at bottom
Fish symbol
Unrecognized sh
Up range
Real-time-window

Menu Operation
8
In most time the default setting is enough. However in some situation, to get a better using, you need adjusting
the menu setting.
Determines how echoes will be displayed on the screen. Increasing the sensitivity will make you see more
details on the screen. In deep water, increasing the sensitivity.
whereas in shallow decreasing the sensitivity.
1) Sensivity
Fish ID. Sens. adjust the threshold of sh size display
Selecting a higher setting allows weak returns being displayed as
sh, which is helpful especially when you are intending to nd
smaller sh species or bait sh.
2) Fish ID. Sens.
How to set a Sensivity?
1）Press MENU Key, and use keypad to choose【Sensivity】
2）Press ENT key to conform the selection.
3）Press UP arrow/Down arrow key to increase/decrease the
value.
4) Press ENT key to conrm the setting.
Selecting a low setting will prevent weak sonar returns being
displayed as sh, which will be very helpful when you are seeking
large species of sh.

Menu List
9
Adjust the threshold of sh size display. higher setting allows weak returns being
displayed as sh, while a low setting will prevent it being displayed as sh.
Set dierent RF channel to allow more than one users operating the device in
the same region without any radio interference.
Separates strong sonar echoes from weak sonar echoes. That makes it easier for
you to distinguish sh for structure from the bottom.
Controls the level of details shown on the display.
Determine in which portion the bottom will be displayed on the screen.
Set the background to black and dimming the backlight automatically.
Badjust the brightness of backlight.
Change the background of the screen.
Set displaying bottom in color mode or in sandy style.
Set if the sonar unit sound a tone or not when a key is pressed.
Fish Alarm sounds when the fishfinder detects what it determines to be a fish.
Sounds when the depth becomes equal to or less than the menu setting.
Sounds when the input battery voltage of display is equal to or less than the setting.
Sounds when the input battery voltage of transmitter is equal to or less than the setting.
Set the units of measure for all depth-related readouts.
Select the display language for menus.
Used to restore original factory setting.
Used to let you practicing using the Fishfinder as if you were on the water.
Show system information of device.
Used to control data transmission with external device.
Sensivity
Depth Range
Night Mode
Backlight
Background
Color Scheme
Beeper
Fish Alarm
Shallow Alarm
Battery of Display
Battery of Boat
Measure Units
Language
System Reset
Simulator
System Info.
Baud Rate
BasicAdvanced
Fish ID. Sens.
Color Line
RF Channel

10
Specifications and Features
Display size: 4.3"TFT LCD; Sunlight Viewable
Resolution: 480*272Pixels; 65,536 color
Language: Multi-language
Monitor and Display Real-time Voltage of Bait boat Battery
IPX6 Level Waterproof Casing Design
Depth Capability: 30m (100ft)
Sonar Frequency: 115Khz
Sonar Beam Angle: 60deg @-10db
Sonar Alarms: Fish / Shallow / Low Battery
RC Distance(field test): Max 300m (1000ft)
Radio Frequency: 2.4Ghz
RF Channels: 20
RC Power: 20dBm
Power of Display: 6~12V lithium battery or 8 * AA Battery
Power of Transmitter: Powered by bait boat battery or DC6~12V/2.0W
Sensor Cable Length: 0.5m
Sonar unit size: 153 x110 x 44mm; Portable Case Size: 262 x 150 x 98mm
Operational Temperature: -10°C ~ 50°C
Water Temp. Included in Transducer
Extreme stable wireless performance even in bad condition
Display target depth reading above each fish symbol
Big / small fish identification
Rugged portable case for a full protection of the fishfinder
Full two-year warranty; extended warranties avaiable
Display
Sonar
R/F
Power
Features
Technical and
casing
SpecicationsFeatures