Garmin PANOPTIX User manual

PANOPTIX™ICE FISHING KIT
INSTALLATION INSTRUCTIONS
Assembling the Portable Mount
You need a Phillips screwdriver to assemble the portable mount.
1Insert the handle into the two openings on the portable mount base .
2Secure the handle to the base using the two 42 mm machine screws and two nuts .
3Slide the included hook and loop straps through the narrow slots beside the battery compartment.
4If you are installing a Panoptix LiveScope™ sonar module , using the eight included 21 mm screws , split
washers, and flat washers, attach the two included brackets to the module, and secure the brackets to
the portable mount.
5Align the chartplotter bail mount over the hole pattern that matches your bail mount, with the openings on
the top of the bail mount facing the back of the base.
GUID-C5E8D7D2-C09F-45FD-82BF-4470A5CE1713 v2March 2021

6Secure the device mount to the base using the four included 24 mm machine screws and the included
washers, if you are installing a metal bail mount.
NOTICE
Only use the included washers if you are installing a metal bail mount. If you are installing a plastic bail
mount, do not use the four included washers.
NOTE: Do not use the self-threading screws included with the chartplotter. Only use the machine-threaded
screws included with this portable kit or use M4 machine screws.
7Place the included rubber washers on the bail-mount knobs, and screw the knobs into the sides of the cradle
or chartplotter.
8Place the cradle or chartplotter into the bail mount, with the rubber washers between the knobs and the
cradle, and tighten the knobs.
The rubber washers enable you to adjust the viewing angle without adjusting the knobs.
9Place the battery (not included) into the battery compartment under the handle.
10 Pull the straps under and around the bottom of the portable mount, and wrap them tightly around the
battery.
Placing the Portable Mount in the Bag
After you have assembled the portable mount, you should place it in the bag, which makes it easier to carry and
protects it from the elements. The bag contains loops that allow you to tether the bag as needed.
1Place the portable mount into the bag.
2If necessary, wrap the excess power cable and transducer cables around the handle.
3Close all of the zippers.
You can use the zipper at the back of the bag for quick access to charge the battery. You can store the wall
charger in the interior zippered pocket, and store the transducer in the exterior side pocket.
2

Connecting the Cables
CAUTION
Ensure that you connect the correct spade connector to the correct battery terminal. Damage to the battery or
device, or bodily harm may occur if the device is improperly connected to the battery (not included).
1Obtain an appropriate power cable and transducer cable to use with your chartplotter and transducer.
The all-in-one power and transducer cable (010-12676-40) works with 7 inch or larger ECHOMAP™
chartplotters.
2Connect the 4-pin power cable and transducer cable to the chartplotter.
3If you are connecting a transducer, connect the power leads to the gray bare wire connectors on the power
cable.
4If you are connecting a Panoptix LiveScope sonar module, connect the 2-pin power cable to the sonar
module.
5Slide the red spade connector onto the positive (red) terminal on the battery.
6Slide the black spade connector onto the negative (black) terminal on the battery.
Limited Warranty
The Garmin® standard limited warranty applies to this accessory. For more information, go to www.garmin.com
/support/warranty.html.
© 2019 Garmin Ltd. or its subsidiaries
Garmin® and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. LiveScope™ and Panoptix™ are trademarks of
Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of Garmin.
3

© 2019 Garmin Ltd. or its subsidiaries support.garmin.com