Toto EcoPower TEL3GSC User manual

0GU3007E 2006.3
1~2
2
3
Important Safeguards .............
Precautions ..............................
Model Number and
Components ..............
NOTE TO INSTALLER : PLEASE GIVE THIS MANUAL TO THE
CUSTOMER AFTER INSTALLATION.
4
4
5
Before Use ...............................
How to Use ...............................
How to Adjust ..........................
6~7
7~8
Maintenance .............................
Periodical Checking ................
9~10
10
Troubleshooting ....................
Specications ..........................
WARRANTY
AUTOMATIC FAUCET
DISCONTINUED

below
local code
Controller
After you read this Instruction Manual, keep it where it can be easily referred to again.
Symbols are shown for safe and proper use of your Automatic Faucet and in order to alert you possible
personal injury and damage to your property. The symbols and their meanings are as follows.
The items of observation are classied and described.
Some models may have dierent component as illustrated below.
Do not install the product in high
humidity area such as shower
room or sauna.
Absolutely "Do not".
Do not disassemble.
Do not
touch the area specied.
This means mandatory.
Do not
Do not use in
humid areas
Do not
disassemble
Never splash water on the controller.
The Automatic Faucet is an electrical appliance, this may cause product
malfunction.
Do not strike or kick to the Automatic Faucet.
This may cause product malfunction or water leakage.
Do not place an item with this symbol displayed in a room
with high humidity such as shower room or sauna.
This may cause product malfunction.
Do not use the Automatic Faucet at temperatures exceeding
what local codes allow.
It may cause product malfunction.
Never attempt to disassemble, reassemble, repair or modify
the
Automatic Faucet, unless you are an electrician .
This may cause product malfunction and electric shock.
Warning
Read these Important Safeguards thoroughly before using your Automatic Faucet, and
follow the precautions carefully.
Warning Ignoring these symbols may cause personal injury or
property damage.
Important Safeguards
(For your safety, please follow the instructions below.)
Getting Started
1
DISCONTINUED

2
How to Use
Getting Started
Disconnect
Controller
Ouch!
No
leakage!
Brrrr
Don't touch
Mandatory
Do not touch the stop valve of the controller, the surface
may be very hot.
This may cause personal injury.
For EcoPowermodel, disconnect the back-up battery
connector, when the Automatic
Faucet is not in use for a
long period of time.
Always close the stop valve(s) before cleaning the strainer .
(Refer to P.8)
Hot or cold water may ow out and cause personal injury or property damage.
Periodically check the piping for leakage.
Ignoring this may cause property damage.
When the room temperature falls under freezing condition,
give proper care to the piping to prevent product malfunction.
If the piping is frozen, the components may suer damage and leakage.
Wrap the piping with heat insulation.
Warning
●Make sure the power cord does not come in contact with the hot-water supply pipe.
(In case of thermostatically controlled mixing valve.)
High temperature may damage the product.
●Avoid placing any objects within the detection range of the infrared sensor.
May result in faulty operation .
●Occasionally turn the temperature control handle of the thermostatically controlled mixing
valve to prevent buildup or sticking.
Debris may form inside of the valve, resulting in impaired performance. Routine maintenance must be performed.
Precautions
(Observe the following precautions.)
DISCONTINUED

Getting Started
3
How to Use Troubleshooting
How to Use
Getting Started
Maintenance Troubleshooting
< Model Number >
Standard
Gooseneck
Single Supply Faucet Thermal Mixing Valve Faucet
Battery type Battery type
TEL3GSC
TEL3GGC
TEL -10
TEL -60
TEL5GSC
TEL5GGC
TEL5DSC
TEL5DGC
TEL3DSC
TEL3DGC
Duration of water discharge : 10 seconds
Duration of water discharge : 60 seconds
Spout
Standard
Battery
Controller
Single Supply Faucet
Thermal Mixing Valve Faucet
P.5
P.5
spout connecting
hose with exible tube
controller
cover
temperature
control handle
water inlet bracket
with strainer
sensor cord
P.5
sensor cord
spout connecting
hose with exible tube
controller
cover
water inlet bracket with strainer
spout connecting
hose with exible tube
P.7
batteries
controller
cover
sensor cord
water inlet bracket
with strainer
P.5
temperature control handle
water inlet bracket
with strainer
spout connecting
hose with exible tube
sensor
cord
controller
cover
P.7
batteries
spout
spout
P.4・6
sensor part
sensor
sensor
cord
spout connecting hose
spout outlet
hexagonal nut
spout connecting hose
hexagonal nut
sensor
cord
spout outlet
EcoPower®type EcoPower®type
EcoPower®
EcoPower
Gooseneck
P.4・6
sensor part
sensor
EcoPower®
Model Number and Components
DISCONTINUED

4
How to Use
Troubleshooting
Make sure all connections are made.
Conrmation of connectors
Cover
Pull
Screw
Battery type
Cover
Screws
Sensor connector
(green)
Battery connector
(for battery type : white)
Sensor connector (green)
Screw
Cover
Battery connector
(for battery type : white)
For Single supply faucet For Thermal mixing valve faucet
1. Place your hands under the faucet.
The sensor will automatically turn on the water.
2. Remove your hands.
The sensor will automatically turn o the water.
Normal operation
Sensor connector (green)
Back-up battery connector (for EcoPowertype : white)
Battery connector (for battery type : white)
Back-up battery connector
(for EcoPowertype : white)
Back-up battery connector
(for EcoPowertype : white)
EcoPowertype
Before Use
How to Use
DISCONTINUED

52
How to Use Maintenance Troubleshooting
Mechanism for Hydropowered generator
The ow of water causes the turbine in the power generator to rotate, which generates electric power, and enables the
Automatic Faucet to operate.
Spout Power generator
1A turbine rotates to
generate power.
2Electric power
is stored.
The Automatic Faucet
is using the charged
power.
3
Water supply
Controller
Controller unit
Solenoid valve
Cover
Coil
Turbine
Using the faucet 11 times a day for 5 seconds or more will fully recharge the faucet.
Turn the temperature control handle.
The water temperature has been factory set to 100°F (38°C).
Depending on the conditions of both the cold and hot water
supply, adjust the temperature by turning the temperature control
handle as necessary.
How to adjust the temperature
Adjustment of the ow rate
※Thermostatically controlled mixing valve
Temperature control handle
Hot
Cold
Open
Close
Stop valve
Bits of Knowledge About EcoPowerModel
With the built-in regulator valve - 1.06gpm (4L/min.), there is no need to adjust the ow rate.
Use the Automatic Faucet with the stop valve fully opened.
If you need to regulate the ow rate, adjust it by turning the stop valve.
However, the EcoPowermodel must be used with the stop valve fully opened.
If you need to regulate the ow rate, make sure the ow rate is more than
0.8gpm (3L/min.).
How to Adjust
DISCONTINUED

16
How to Use
Maintenance
Follow these instructions for daily maintenance.
For general cleaning
For cleaning dirt
Avoid using anything that may scratch the spout surface.
Do not scratch the sensor when cleaning.
Never use polishing powder, detergent that includes coarse particles,
thinner, benzine, acid or alkaline detergent, or a nylon scrub brush.
They will damage the surface of the spout.
Caution
Use a damp, soft cloth to clean the spout and the sensor.
Use a soft cloth with diluted dish washing detergent.
Wipe the area using a wet cloth and dry using a soft cloth.
Sensor part
Outlet
Low Battery Indicator (Battery operated models)
If continued to use after
1ST indication
2ND Indication1ST Indication
Flow time reduced to 2
seconds. (Normally 10
or 60 seconds)
Water ow will stop and
sensor light will blink every
4 seconds.
Sensor light
Sensor
Use only AA alkaline batteries (2pcs) .
2 years battery life expectancy ,
based on 4,000 cycles per month.
Replace batteries every 2 years as
preventative maintenance.
Battery Specications
Use soft cloth for maintenance
Maintenance
DISCONTINUED

7
How to Use Maintenance
No
leakage!
1. Remove the controller cover. (See page 4)
2. Detach the battery connector (white).
3. Remove the rubber cover from the battery
case and replace the AA alkaline batteries.
4. Reassemble.
Replace only with 2 AA alkaline batteries.
Follow the "battery warning note" on the
batteries.
Please remove batteries from the faucet
when not in use for a long period of time.
Caution
battery case
controller
battery case
controller
For Thermal mixing valve faucet For Single supply faucet
Battery Replacement Procedure (Battery operated models)
battery connector
(white)
Disconnect white
connector by hand
battery connector (white)
batteries
rubber cover
battery case
Please check your Automatic Faucet at least once a month according to the following instructions.
Check the piping to see whether there is any leakage.
Ignoring this may cause property damage.
Leakage
For thermostatically controlled mix valve, turn the
temperature control handle four or ve times.
Build up may form inside, resulting in impaired performance
if maintenance is not performed.
Water temperature
Temperature
control handle
Controller
Periodical Checking
DISCONTINUED

8
Maintenance
Check if the spout is loose.
If the spout is loose, tighten the hexagonal nut underneath the spout.
Loose spout
1. Close the stop valve.
2. Remove the strainer cover with the open-close
tool.
3. Pull out the strainer and clean it with a brush.
4. Put the strainer back in its place.
5. Reopen the stop valve fully.
Cleaning the strainer
1. Remove the spout nozzle with the supplied
open-close tool.
2. Clean the spout nozzle with a brush to
remove dirt from the screen.
3. Set the spout nozzle back in place.
Cleaning of the spout nozzle
Flow rate
Stop valve
Open
Close
Open-close tool
Strainer
Strainer cover
Open
Brush
Strainer
Open-close tool
Open
Close
Brush
Spout nozzle
Spout nozzle
When the strainer or spout nozzle is clogged, the ow rate
will decrease.
Make sure to clean the strainer and the spout nozzle.
Pay special attention to the Eco power model, since low ow
rate may result in low power generation. (see page 5)
DISCONTINUED

9
Troubleshooting
Before contacting a repairman, check the following common problems and solutions. If the problem persists contact your dealer.
Problem Cause Solution Ref. page
Water doesn't run.
Water doesn't stop.
The surface of the sensor is dirty. Clean the surface of the sensor. P.6
P.2
P.5
P.5
P.5
P.5
P.5
P.5
P.4
P.4
P.8
P.8
P.7
P.7
P.6
P.2
The surface of the sensor is dirty. Clean the surface of the sensor.
There is an obstruction in front of the sensor. Remove the obstruction.
There is an obstruction in front of the sensor. Remove the obstruction.
The stop valve is turned o. Turn on the valve.
Connect the backup battery connector.
The power generator and sensor connection
are not attached. Securely attach the connector(s).
Water supply is suspended. Wait until water supply is restored.
The strainer or the spout nozzle is clogged. Clean the strainer and the spout nozzle.
The batteries are dead. Replace the batteries.
Battery-operated model: No batteries installed. Install batteries in the controller.
If water continues to run after attempting above, turn o the stop valve.
Low ow rate. Stop valve is not fully opened. Open the stop valve fully.
The strainer or the spout nozzle is clogged. Clean the strainer and the spout nozzle.
Water temperature
is too high.
Water temperature
is too low.
The temperature control handle is set at "H". Set the temperature control handle to
the middle point.
The stop valve connected to the cold-water
supply is not fully opened. Open the cold-water stop valve fully.
The temperature control handle is set at "C".
Set the temperature control handle to
the middle point.
The stop valve connected to the hot- water
supply is not fully opened. Open the hot-water stop valve fully.
The hot-water supply temperature is lower
than 120°F (49°C).
Set the hot-water supply temperature
to 120°F (49°C).
The strainer or the spout nozzle is clogged.
The batteries are dead.
Water temperature
is not controlled
properly.
Water ow from the
faucet stops about 2
seconds later.
Clean the strainer and the spout nozzle.
Replace the batteries.
One side of the stop valve is not fully opened. Open the stop valve fully. P.5
P.8
P.7
The self-adjusting sensor may not work
properly
when stained or blocked by water
droplets.
Short detection range.
Clean the sensor surface. P.6
EcoPowermodel: Backup battery connector
is disconnected.
Troubleshooting
DISCONTINUED

10
Troubleshooting
Phenomenon Explanation
After sometime water stops
owing even if your hands are
still under the faucet.
After removing hands, water
keeps running for 15 seconds.
The sensor activates by detecting hand movements. If your hands are not moving,
it will be regarded as an ordinary object.
Even if your hands are moving , the faucet will only keep running for 10 seconds or 60
seconds for safety purposes.
If the sensor is stained or blocked by water droplets, the water may keep running even
after you removed your hands.
In such a case, the self-adjusting sensor will stop the water after 15 seconds.
Always wipe o all water droplets and stains from the sensor.
This automatic faucet is equipped with a self-adjusting sensor which automatically adjust its detection range once every 15 seconds.
This sensor may exhibit the following phenomena.
Note these are implemented for safety and conservation purposes, they are not malfunctions.
Battery
Power supply
-
-
Alkaline type AA batteries 1.5V×2pcs.
Battery life 2 yrs. Life based on 4,000 cycles per month
Detection range
from the sensor
5-1/8"～7-7/8" (130～200 mm)
sensor is self-adjusting
Water supply pressure
minimum required water pressure : 7 PSI (50 kPa) (Flowing) for Single faucet
: 13 PSI (90 kPa) (Flowing) for Thermal mixing faucet
maximum water pressure : 125 PSI (862 kPa)
Water supply connection
1/2" NPSM
Ambient temperature 32～104°F(0～40°C)
Humidity Max. 90% RH
Flow rate 1.06 gallon per minutes (4 L/ min.)
controlled by governor
Duration time of
water discharge
10 seconds
60 seconds
Discharge quantity
Max. 0.25 gallon per cycle (0.95 L/cycle) for 10 seconds type
EcoPower®
Specications
DISCONTINUED

WARRANTY
©2006 TOTO  USA, Inc. á 1155 Southern Road, Morrow GA 30260
Phone [phone] Fax [phone] www.totousa.com
TOTO
 USA, INC. is a wholly owned subsidiary of TOTO  Ltd.
Printed in March, 2006
0GU3007E
4. This warranty gives you specic legal rights. You may have other rights which vary from State to State or
province to province.
3. This warranty does not apply to the following items:
a) Damage or loss sustained in a natural calamity such as re, earthquake, ood, thunder, electrical
storm, etc.
b) Damage or loss resulting from any unreasonable use, misuse, abuse, negligence, or improper
maintenance of the product.
c) Damage or loss resulting from removal, improper repair, or modication of the product.
d) Damage or loss resulting from sediments or foreign matter contained in a water system.
e) Damage or loss resulting from improper installation or from installation of a unit in a harsh and/or
hazardous environment.
f) Damage or loss resulting from acts of animals such as mice and insects.
g) Damage or loss resulting from a use of abnormal power supply.
h) Damage or loss resulting from abrasion of consumable supplies.
i) Damage or loss resulting from frost.
1. TOTOwarrants its products to be free from manufacturing defects under normal use and service for a period
of three (3) years from the date of purchase. This warranty is extended only to the ORIGINAL PURCHASER and
applies only to product purchased and installed in North America.
THIS WRITTEN WARRANTY IS THE ONLY WARRANTY MADE BY TOTO. REPAIR OR REPLACEMENT AS PROVIDED
UNDER THIS WARRANTY SHALL BE THE EXCLUSIVE REMEDY AVAILABLE TO THE PURCHASER. TOTO SHALL NOT
BE RESPONSIBLE FOR LOSS OF USE OF THE PRODUCT OR FOR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL
DAMAGES OR EXPENSES INCURRED BY PURCHASER, OR FOR LABOR OR OTHER COSTS DUE TO INSTALLATION OR
REMOVAL, OR COSTS OF REPAIRS BY OTHERS, OR FOR ANY OTHER EXPENSE NOT SPECIFICALLY STATED ABOVE.
EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES, INCLUDING THAT OF
MERCHANTABILITY OR FITNESS FOR USE, ARE EXPRESSLY LIMITED TO THE DURATION OF THIS WARRANTY.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS. OR THE EXCLUSION
OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION AND EXCLUSION
MAY NOT APPLY TO YOU.
5. To obtain warranty repair service under this warranty, you must take the product or deliver it prepaid to a
TOTOservice facility together with a letter stating the problem, or contact a TOTOdistributor or products
service contractor, or write directly to TOTOU.S.A., INC., 1155 Southern road, Morrow, Georgia 30260, (888)
295-8134. If, because of the size of the product or nature of the defect, the product cannot be returned to
TOTO, receipt by TOTO of written notice of the defect shall constitute delivery. In such case, TOTO may
choose to repair the product at the purchaser’s location or pay to transport the product to a service facility.
2. TOTO’s obligations under this warranty are limited to repair or replacement, at TOTO’s option, of products
or parts found to be defective, provided that such products were properly installed and used in accordance
with OWNER’S MANUAL. TOTOreserves the right to make such inspections as may be necessary in order to
determine the cause of the defect. TOTOwill not charge for labor or parts in connection with warranty
repairs or replacements. TOTOis not responsible for the cost of removal, return and/or reinstallation of
products.
DISCONTINUED