TouchMagix MotionMagix MAGIXBOX User manual

MAGIXBOXTM
Quick Start Guide
MotionMagixTM
by TouchMagix
MAGIXBOXTM
Quick Start Guide
MotionMagixTM
by TouchMagix
TM

Four Arms, Screws and Allen Keys
Projector Mount Top
Ceiling
Plate
Extendable
Rod
Connector
Piece
Middle
Piece
Projector Mount Bottom
Ankle
Universal Spider
MagixBox
Super clamp with ball socket
Adapter
Safety Cable
What’s in the box:

MagixBox
Interactive Wall Setup with Clamp
HDMI Cable
Assembly Instructions:
Wireless Keyboard
1. Select desired location on the ceiling and assemble
the projector mount on it.
2. Mount your projector.
3. Attach MagixBox on the projector mount using Super Clamp.
4. Connect HDMI cable from MagixBox to the projector.
5. Connect power adapter for MagixBox and Projector to
standard AC outlet.
6. Power on the projector and adjust the display area.
7. Start the MotionMagix software and follow given steps.
8. All set to go. Enjoy the MotionMagix experience.
MagixBox
Interactive Wall Setup with separate Projector mount

Interactive Floor Setup with Clamp
Interactive Floor Setup with separate Projector mount
Attach the ceiling plate to the ceiling
using the dry wall screws.
Step 1
Fix the extendable bar by
rotating it in clockwise.
Step 2
Rotate to
fit in
Step 4
Attach the projector to the universal
spider using the designated holes to
screw in the four arms. Once done
make sure all the screws from Step 3
are tightened.
Step 3
Attach the four arms to the universal
spider using screws and washers. Do
not completely tighten the screws yet.
Step 5
Carefully hook the ankle atop the universal spider to
the middle piece at the end of the extendable bar
attached to the ceilings. Tilt the ankle to ensure lens
of projector points towards projection surface and
tighten the screws on the ankle tightly to hold it firm
and steady.
Projector Installation
MagixBox

MotionMagix
MotionMagic
L
ock
L
ock
L
ock
Lock Lock Lock
MotionMagix
Step 6 Step 7
Step 8
Tightly fix in the ball socket head into
the designated hole on the MagixBox
by rotating it clockwise.
Carefully lift the MagixBox with the
extension arm and use the super
clamp to attach it the projector mount
fixed to the ceiling. Tighten the super
clamp using the long knob till the grip
is very firm and steady.
Adjust the angle of the attached MagixBox using the knob on the ball socket to
make sure the sensor is approximately pointed towards the projection surface.
Once adjusted, tighten the knob sufficiently to hold the MagixBox firm and
steady.
A. Press the button (lock)
& simultaneously pull the
knob
B. Rotate it counter-
clockwise (while pulling)
C. Release the knob &
tighten it by rotating it in
clockwise direction
MagixBox Clamping
MotionMagix
MotionMagix
Step 9
Step 11
Step 10
Loop the safety cable around
the extendable bar as shown and
insert and lock the carabiner on the
designated whole on the top backside
of the MagixBox.
Connect the MagixBox and the Projector to power supply and connect them to
each other using the HDMI cord.
Power Adaptor
HDMI
Power Cable
Insert the wireless keyboard’s dongle
into the MagixBox’s USB port.

Alternate Setup (When projector is pre-installed)
1. Unscrew the Super clamp from the ball socket rod.
2. Unscrew the connector piece and middle piece from the rest of the
projector mount.
3. Unscrew the middle piece from the connector piece.
4. Screw in the free end of the ball socket rod into the connector
piece and secure it from the other end using a nut.
5. Screw in the MagixBox to the ball socket end securely.
6. Screw in the new assembly to either the extension rod of the
projector mount or the ceiling plate directly.
Steps:
MagixBoxTM powering instructions
1. The MagixBoxTM system automatically powers ON when connected to AC power.
2. On successful booting of the OS, the pre-installed MotionMagixTM software will
automatically start.
3. Connect the system to the internet via WiFi.
4. Log In into MotionMagixTM software if you are an existing user OR simply Sign Up
to get registered as a new user.
5. If you accidentally shutdown the system, just switch OFF the mains AC power,
wait for 10-15 seconds and switch ON the mains again to Power ON the system.
MotionMagixTM
Calibration
Scheduler
Tools
Help
MotionMagixTM
by TouchMagix
English
X
-
Help

Your MagixBox is designed and tested to
meet the latest standards of safety for
Interactive technology use. However, to
ensure your and the device safety, it’s
important that you read the following
safety instructions:
 Do not use this product near water or
a heat source such as a radiator.
 Openings on the chassis are for
ventilation, do not block or cover these
openings.
 Make sure to leave plenty of space
around the system for ventilation.
 Use this product in environments with
ambient temperatures between 0 to 55 C.
 Do not spill water or any other liquid
on your system.
 Do not walk on the power cord or
anything to rest on it.
 Do not look into the lens while the
projector is ON. The strong light from the
lamp may damage your eyes.
 Do not overload the power outlet as
this can result in fire or electrical shock.
Safety information
MotionMagixTM
by TouchMagix
If you encounter the following technical
problems with the product, unplug the
power cord and contact:
[email protected]
 The system does not function properly
even if you follow the operating
instructions.
 The system was stopped or the cabinet
is damaged.
 The power cord or plug is damaged.
 Liquid has been spilled into the system.
 The system performance changes.
For support, call us at [phone]
or please visit
www.motionmagix.com/support