Christie DS+26 User manual

Lamp Replacement Instructions
013-100357-02 (Rev. 1) 1 of 5 Pages
Introduction
Use the following instructions when replacing the lamp on the projector model listed in
Table 1, below. The lamp is located at the front of the projector and can be accessed by
removing the front cover. Use only a Christie approved Lamp Kit for the specific projector
model.
Projector Model Model Number Required Lamp Kit
Christie DS+26 115-003101-01 003-120181-01
Warnings
Lamp replacement MUST be performed by a qualified service technician.
Cool the lamp completely (approximately 60 minutes) and handle by the housing
only.
Install the correct wattage lamp, supplied by Christie (Refer to Table 1. Projector
Models) and read the Lamp Replacement Procedure in its entirety before proceeding.
Do not touch the glass surface of the lamp. Fingerprints left on the surface can lead
to an intense accumulation of heat known as a “hotspot”, which could potentially
cause the lamp to shatter. It is recommended to wear clean, lint-free gloves and a
face shield when working with the lamp.
In the unlikely event that the bulb ruptures, small glass fragments may come loose.
The lamp module is designed to contain the glass fragments; however, it is advised
that extreme caution is exercised when removing the lamp module.
Table 1. Projector Models

Lamp Replacement Instructions
013-100357-02 (Rev. 1) 2 of 5 Pages
Lamp Replacement Procedure
Please read before proceeding
WARNING
Always power down and unplug the projector prior to servicing.
Allow the lamp to cool before handling.
STEP 1 - TURN THE LAMP OFF
Press (power) to turn the projector OFF. Allow the cooling fans to stop automatically
(approximately five minutes) before proceeding with Step 2.
STEP 2 - UNPLUG THE PROJECTOR
When the cooling fans have stopped, turn the projector’s main switch OFF and unplug
from the main power source. Wait approximately 60 minutes to allow sufficient time for
the lamp to cool down. Do not open the lamp cover until this time has elapsed.
STEP 3 - REMOVE FRONT COVER
Release the front cover screw and remove the front cover. Refer to Figure 1.
Figure 1. Remove Front Cover

Lamp Replacement Instructions
013-100357-02 (Rev. 1) 3 of 5 Pages
STEP 4 - REMOVE THE LAMP MODULE
(a) Unscrew the three mounting screws securing the lamp module. Refer to Figure 2.
(b) Release the handle. Refer to Figure 2.
(c) Remove the lamp module from the projector housing. Refer to Figure 2.
STEP 5 — INSERT NEW LAMP MODULE
(a) Use the designated guide pins to insert the new lamp module. Refer to Figure 3.
(b) Firmly screw-in the three mounting screws to secure the lamp module. Do not use
excess force. Refer to Figure 3.
(c) Secure the handle. Refer to Figure 3.
Figure 2. Remove Lamp Module
Figure 3. Insert New Lamp Module

Lamp Replacement Instructions
013-100357-02 (Rev. 1) 4 of 5 Pages
STEP 6 — REPLACE FRONT COVER
IMPORTANT
The lamp module is calibrated for maximum performance and brightness
in this projector. Do not attempt to re-align or adjust the lamp module.
Replace the front cover and tighten the front cover screw to secure the cover to the
projector housing. Do not use excess force. Refer to Figure 4.
STEP 7 — RESET THE LAMP HOURS
Once the lamp is replaced it is important to reset the lamp properties. To do this access the
User Menu, use the up/down scroll to highlight the LAMP RESET option and click on the
arrow icon. Refer to Figure 5.
Figure 4. Replace Front Cover
Figure 5. User Menu

Lamp Replacement Instructions
013-100357-02 (Rev. 1) 5 of 5 Pages
Technical Support
NORTH AMERICA
CHRISTIE Digital Systems, Inc.
809 Wellington St. North
Kitchener, Ontario, Canada N2G 4Y7
Tel. [phone] (General)
Toll Free 1-800-221-8025 (Technical Support)
Fax [phone] (Service)
CHRISTIE Digital Systems, Inc.
10550 Camden Drive
Cypress, CA 90630 USA
Tel. [phone] (General)
Toll Free 1-800-221-8025 (Technical Support)
Fax [phone] (Service)
EUROPE
CHRISTIE Digital Systems, Inc.
View Point
200 Ashville Way
Wokingham, Berkshire RG41 2PL
United Kingdom
Tel. [phone]
Fax [phone]
CHRISTIE Digital Systems, Inc.
Willicher Damm 129
D-41061 Mönchengladbach
Germany
Tel. [phone]
Fax [phone]
CHRISTIE Digital Systems, Inc.
7, av Georges Pompidou
92593 Levallois-Perret Cedex
France
Tel. [phone]
Fax [phone]
ASIA-PACIFIC / OTHER
CHRISTIE Digital Systems, Inc.
627A Aljunied Road
# 05-02 Biz Tech Centre
Singapore 389842
Tel. [phone]
Fax [phone]
CHRISTIE Digital Systems, Inc.
Rm. 1109-1116 Shartex Plaza
No. 88 Zun Yi South Road
Shanghai, 200336
People’s Republic of China
Tel. [phone]
Fax [phone]
CHRISTIE Sales (Canada) CHRISTIE Sales (U.S.)
Tel. [phone] Tel. [phone] or 1-866-880-4462
Fax [phone] Fax [phone]