Digital Projection E-Vision Laser WQ120 Series User manual

Rev A May 2018
E-Vision Laser WQ120 Series
High Brightness Digital Video Projector
4INSTALLATION AND QUICKSTART GUIDE
4CONNECTION GUIDE
4OPERATING GUIDE
4REFERENCE GUIDE
119-656

page i
Digital Projection E-Vision Laser WQ120 Series
Rev A May 2018
About This Document
Follow the instructions in this manual carefully to ensure safe and long-lasting use of the projector.
Symbols used in this manual
Many pages in this document have a dedicated area for notes. The information in that area is accompanied by the following symbols:
WARNING: this symbol indicates that there is a danger of physical injury to yourself and/or damage to the equipment unless
the instructions are closely followed.
ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical shock unless the instructions are closely
followed.
LASER WARNING: this symbol indicates that there is a potential hazard of eye exposure to laser radiation unless the
instructions are closely followed.
NOTE: this symbol indicates that there is some important information that you should read.
Product revision
Because we at Digital Projection continually strive to improve our products, we may change specications and designs, and add new features
without prior notice.
Updates may be available online - visit the Digital Projection website for all latest documents.
Legal notice
Trademarks and trade names mentioned in this document remain the property of their respective owners.
Digital Projection disclaims any proprietary interest in trademarks and trade names other than its own.
Copyright © 2018 Digital Projection Ltd. All rights reserved.
Notes

page ii
Digital Projection E-Vision Laser WQ120 Series
Rev A May 2018
Laser Information
Caution-useofcontrolsoradjustmentsorperformanceofproceduresotherthanthosespeciedhereinmayresultin
hazardous radiation exposure.
Optical radiation
Caution - possibly hazardous optical radiation emitted from this product. Do not stare at operating light source. May be
harmful to eyes. This projector is tested according to IEC/EN62471-5:2015 (Photobiological safety of lamps and lamp
systems – Part 5: Image projectors” standard) to be Risk Group 2 (low risk).
Notes
LASER LIGHT
AVOID DIRECT EYE EXPOSURE
CLASS 3R LASER PRODUCT
455-470nm <13Watts
CLASSIFIED EN/IEC 60825-1 2007
RG2
CAUTION: Do not look into the lens

page iii
Digital Projection E-Vision Laser WQ120 Series
Rev A May 2018
Introduction
Congratulations on your purchase of this Digital Projection product.
Your projector has the following key features:
• Displays WQXGA.
• HDBaseT® for transmission of uncompressed High Denition Video up to 100 m from the source.
• 3G-SDI with loop-through.
• Separate control of screen and source aspect ratio.
• Control via LAN and RS232.
• Motorised lens mount.
A serial number is located on the side of the projector. Record it here:
Notes

page iv
Digital Projection E-Vision Laser WQ120 Series
Rev A May 2018
CONTENTS
INSTALLATION AND QUICK-START GUIDE..........................1
WHAT’S IN THE BOX?.................................................................. 3
CONNECTING THE POWER SUPPLY........................................... 4
Voltage selection................................................................................... 4
PROJECTOR OVERVIEW ............................................................. 5
Front and rear views ............................................................................. 5
Control panel......................................................................................... 6
Projector indicators ................................................................................ 7
REMOTE CONTROL ..................................................................... 8
Infrared reception................................................................................ 11
POSITIONING THE SCREEN AND PROJECTOR ....................... 12
Roll and pitch ...................................................................................... 13
CHANGING THE LENS ............................................................... 14
Inserting a new lens ............................................................................ 14
Removing the lens .............................................................................. 14
OPERATING THE PROJECTOR ................................................. 15
Switching the projector on................................................................... 15
Switching the projector o󰀨................................................................... 15
Selecting an input signal ..................................................................... 16
Selecting a test pattern ....................................................................... 16
Adjusting the lens................................................................................ 17
Adjusting the image............................................................................. 17
CONNECTION GUIDE..........................................................................19
SIGNAL INPUTS ......................................................................... 21
Digital inputs and outputs.................................................................... 21
EDID on the DisplayPort, HDMI and HDBaseT inputs........................ 22
Using DisplayPort/HDMI/HDBaseT switchers with the projector ........ 22
CONTROL CONNECTIONS......................................................... 23
LAN connection examples .................................................................. 24
RS232 connection example ............................................................... 25

page v
Digital Projection E-Vision Laser WQ120 Series
Rev A May 2018
OPERATING GUIDE ..............................................................................27
USING THE MENUS.................................................................... 29
Opening the OSD................................................................................ 29
Opening a menu.................................................................................. 29
Exiting menus and closing the OSD.................................................... 29
Inside a menu...................................................................................... 30
Accessing sub-menus........................................................................... 30
Executing commands............................................................................ 30
Editing projector settings..................................................................... 31
Using a slider to set a value.................................................................... 31
Editing numeric values .......................................................................... 31
USING THE PROJECTOR........................................................... 32
Main menu .......................................................................................... 32
Lens menu .......................................................................................... 33
Lens Control....................................................................................... 33
Lens Memory...................................................................................... 34
Image menu ........................................................................................ 35
Color menu.......................................................................................... 36
Color Space ....................................................................................... 36
Color Mode ........................................................................................ 37
Geometry menu .................................................................................. 42
Aspect Ratio....................................................................................... 42
Digital Zoom....................................................................................... 44
Overscan........................................................................................... 45
Laser menu ......................................................................................... 46
Setup menu......................................................................................... 47
ColorMax........................................................................................... 49
Power On/O...................................................................................... 50
Clock Adjust ....................................................................................... 51
OSD Settings...................................................................................... 52
Memory............................................................................................. 52
Network menu..................................................................................... 53
Information menu ................................................................................ 54
Signal Format ..................................................................................... 54
System Status .................................................................................... 55
Thermal Status.................................................................................... 55
Factory Reset ..................................................................................... 56
SERVED WEB PAGES ................................................................ 57
CHOOSING A LENS.................................................................... 69
Basic calculation ................................................................................. 70
Basic calculation example................................................................... 71
Full lens calculation............................................................................. 72
Introducing TRC .................................................................................. 72
Calculating TRC .................................................................................. 73
Calculating the throw ratio with TRC ......................................................... 74
Full lens calculation example .............................................................. 75
POSITIONING THE IMAGE......................................................... 76
APPENDIX A: LENS PART NUMBERS ....................................... 78
APPENDIX B: SUPPORTED SIGNAL INPUT MODES ................ 79
2D formats........................................................................................... 79
SDI formats ......................................................................................... 82
APPENDIX C: WIRING DETAILS ................................................ 83
RS232 ................................................................................................. 83
Trigger 1 & Trigger 2 ........................................................................... 84
Wired remote control........................................................................... 84
APPENDIX D: GLOSSARY OF TERMS....................................... 85
CONTENTS (continued)

Rev A May 2018
E-Vision Laser WQ120 Series
High Brightness Digital Video Projector
INSTALLATION AND QUICKSTART GUIDE
4

Digital Projection E-Vision Laser WQ120 Series
Installation and Quick-Start Guide
CONTENTS
Rev A May 2018
CONTENTS
WHAT’S IN THE BOX? ...........................................................................3
CONNECTING THE POWER SUPPLY..........................................4
VOLTAGE SELECTION ................................................................. 4
PROJECTOR OVERVIEW.....................................................................5
FRONT AND REAR VIEWS ........................................................... 5
CONTROL PANEL......................................................................... 6
Projector indicators ............................................................................... 7
REMOTE CONTROL ................................................................................8
INFRARED RECEPTION............................................................. 11
POSITIONING THE SCREEN AND PROJECTOR...............12
ROLL AND PITCH....................................................................... 13
CHANGING THE LENS........................................................................14
INSERTING A NEW LENS........................................................... 14
REMOVING THE LENS ............................................................... 14
OPERATING THE PROJECTOR.....................................................15
SWITCHING THE PROJECTOR ON............................................ 15
SWITCHING THE PROJECTOR OFF .......................................... 15
SELECTING AN INPUT SIGNAL................................................. 16
SELECTING A TEST PATTERN .................................................. 16
ADJUSTING THE LENS.............................................................. 17
ADJUSTING THE IMAGE............................................................ 17

page 3
Digital Projection E-Vision Laser WQ120 Series
Installation and Quick-Start Guide
WHAT’S IN THE BOX?
Rev A May 2018
What’s In The Box? Notes
Make sure your box contains
everything listed. If any pieces are
missing, contact your dealer.
You should save the original box
and packing materials, in case you
ever need to ship your projector.
The projector is shipped without a
lens.
Only one power cable - dependent
on the destination territory - will be
supplied with the projector.
Remote control
Pic Mute
OPEN CLOSE
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
DisplayPort1
HD-T 3GSDI
VGA COMP1 COMP2
HDMI3
TEST
HDMI4
DisplayPort2
R G B ALL
3D EYE PIP SWAP
456
7 8 9 0
ALT
ADDR
OSD
OFF ON
DEFAULT
FREEZE RE-SYNC
A B C D
USER PRESET
2x AAA batteries
User Manual on disc Important Information
Power cable, Europe Power cable, North America
Projector
Power cable, United Kingdom
Security screw
Power cable, China
HDMI cable

page 4
Digital Projection E-Vision Laser WQ120 Series
Installation and Quick-Start Guide
CONNECTING THE POWER SUPPLY
Rev A May 2018
Connecting The Power Supply
Adjust the VOLTAGE SELECT switch 1 to the required voltage, then rmly push the mains connector into the socket 2.
Voltage selection
The VOLTAGE SELECT switch must be set to match the power supply you are using:
Voltage of power supply used Position of VOLTAGE SELECT switch
AC100-130V outlet
AC200-240V (single phase) outlet
Notes
Use only the power cable
provided.
Ensure that the power outlet
includes a ground connection as
this equipment MUST be earthed.
Handle the power cable carefully
and avoid sharp bends. Do not
use a damaged power cable.
1
2

page 5
Digital Projection E-Vision Laser WQ120 Series
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Rev A May 2018
Projector Overview
Front and rear views
1Air inlet
2Front infrared window and indicators
3Air inlet
4Lens mount
5Rear infrared window
6Air outlet
7Connections panel
8Control panel
9Adjustable feet
10 Voltage selector
11 Mains socket and switch
12 Air inlets
Front view
4
3
2
1
Rear view
9
8
576
1110
Bottom view
12
Notes

page 6
Digital Projection E-Vision Laser WQ120 Series
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Rev A May 2018
Control panel
1POWER
Switches the projector on and o󰀨
(STANDBY).
2INPUT
Switches to the next input source.
3AUTO SYNC
Re-synchronises with the current input
signal.
4ASPECT
Changes the aspect ratio.
5CENTER LENS
Centers the lens.
6PIC MUTE
Shows and hides the projected image.
When OFF, the light source is completely
switched o󰀨 and the screen is black.
7MENU
Displays and exits the OSD.
8Arrow buttons & ENTER
Navigation buttons used to highlight menu
entries in the OSD.
Press ENTER to open or execute the
highlighted menu entry.
9EXIT
Exits the current OSD page and enters the
level above.
10 LENS SHIFT arrow buttons
Each of these buttons moves the lens in the
specied direction.
11 FOCUS plus and minus buttons
Used to move the focus in and out.
12 ZOOM plus and minus buttons
Used to zoom in and out.
POWER
INPUT AUTO
SYNC ASPECT CENTER
LENS PIC MUTE
1 2 3 4 5 6
7 8 9 10 11 12
Notes

page 7
Digital Projection E-Vision Laser WQ120 Series
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Rev A May 2018
Projector indicators
TEMP. O󰀨 = no problem
Flashing red = temperature error
LIGHT O󰀨 = light is switched o󰀨
Flashing green = light is preparing to switch on
Flashing red (cycles of six ashes) = light module failure
On, red = light module has reached end of life
On, green = light is switched on
STATUS O󰀨 = no problem
Flashing red (continuously) = cover error
Flashing red (cycles of four ashes) = fan error
On, red = system error
POWER O󰀨 = the projector is switched o󰀨
Flashing green = the projector is warming up
Flashing amber = the projector is cooling down
On, red = STANDBY mode
On, green = the projector is switched on
Notes
POWERSTATU SLIGHTTEMP.

page 8
Digital Projection E-Vision Laser WQ120 Series
Installation and Quick-Start Guide
REMOTE CONTROL
Rev A May 2018
Remote Control
1Power ON / OFF
Turns power on and o󰀨.
2Pic Mute OPEN / CLOSE
Shows and hides the projected image.
When OFF, the light source is completely switched o󰀨 and the screen is black.
2OSD ON / OFF
Enable and disable screen timeout messages and control whether to show the OSD
during projection.
4MENU
Access the OSD. If the OSD is open, press this button to go back to the previous menu.
5Navigation (arrows and OK)
Navigate through the menus with the arrows, conrm your choice with OK.
In lens adjustment modes, the arrows are used to move, zoom or focus the lens. See 11
below.
In lens adjustment modes, or when the OSD is not showing, the OK button switches
between modes: Shift Adjustment and Zoom / Focus Adjustment.
6EXIT
Go up one level in the OSD. When the top level is reached, press to close the OSD.
7FREEZE
Freeze the current frame.
8DEFAULT
When editing a parameter, press this button to restore the default value.
9INFO
Access information about the projector.
10 RE-SYNC
Re-synchronise with the current input signal.
continues on next page...
Pic Mute
OPEN CLOSE
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
DisplayPort1 HD-T 3GSDI
VGA COMP1 COMP2
HDMI3
TEST
HDMI4
DisplayPort2
R G B ALL
3D EYE PIP SWAP
456
7 8 9 0
ALT
ADDR
OSD
OFF ON
DEFAULT
FREEZE RE-SYNC
A B C D
USER PRESET
1
2
5
6
8
4
9
7
3
10
Notes
This projector does not use the
following options on the remote:
DVI, VGA, COMP 1, COMP 2,
HDMI 3, HDMI 4, DISPLAYPORT2,
3D, EYE, PIP and SWAP.
Remote control

page 9
Digital Projection E-Vision Laser WQ120 Series
Installation and Quick-Start Guide
REMOTE CONTROL
Rev A May 2018
11 LENS adjustment
FOCUS IN / OUT: adjust focus.
SHIFT: press and hold this button, then use the Navigation arrow
buttons to move the lens.
ZOOM IN / OUT: adjust zoom.
12 USER PRESET A, B, C, D
Load user presets.
13 ALT
Press and hold this button to access alternative functions for all
buttons with a green label.
14 DVI / DisplayPort2 / Numeric input 3
There is no DVI or DisplayPort2 input on this projector.
15 HDMI 2 / HDMI 4 / numeric input 2
Select the HDMI 2 input.
There is no HDMI 4 input on this projector.
16 HDMI 1 / HDMI 3 / numeric input 1
Select the HDMI 1 input.
There is no HDMI 3 input on this projector.
17 TEST / SWAP / numeric input 0
Show a test pattern. Press again to show the next test pattern:
...O, White, Black, Red, Green, Blue.
There is no SWAP function on this projector.
continues on next page...
Notes
This projector does not use the
following options on the remote:
DVI, VGA, COMP 1, COMP 2,
HDMI 3, HDMI 4, DISPLAYPORT 2,
3D, EYE. PIP and SWAP.
Remote control
Pic Mute
OPEN CLOSE
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
DisplayPort1 HD-T 3GSDI
VGA COMP1 COMP2
HDMI3
TEST
HDMI4
DisplayPort2
R G B ALL
3D EYE PIP SWAP
456
7 8 9 0
ALT
ADDR
OSD
OFF ON
DEFAULT
FREEZE RE-SYNC
A B C D
USER PRESET
13
11
12
14
15
16
17

page 10
Digital Projection E-Vision Laser WQ120 Series
Installation and Quick-Start Guide
REMOTE CONTROL
Rev A May 2018
18 DISPLAYPORT 1 / R / numeric input 4
Select DisplayPort 1 input.
19 HD-T / G / numeric input 5
Select the HDBaseT input.
20 3GSDI / B / numeric input 6
Select the 3G-SDI input.
21 VGA / 3D / Numeric input 7
There is no VGA input or 3D function on this projector.
22 COMP1 / EYE / Numeric input 8
There is no Component 1 input or EYE function on this projector.
23 COMP2 / PIP / Numeric input 9
There is no Component 2 input or PIP function on this projector.
24 ADDR / ALL (with red indicator at the top)
Assign and unassign an IR remote address.
To assign an address:
1. Press and hold this button until the indicator starts ashing.
2. Release this button and while the indicator is still ashing, enter
a two-digit address using the numeric input buttons. The indicator
will ash three times quickly to conrm the change.
To unassign an address and return to the default address 00,
• Press and hold ALT and this button simultaneously until the
indicator ashes to conrm the change.
Notes
This projector does not use the
following options on the remote:
DVI, VGA, COMP 1, COMP 2,
HDMI 3, HDMI 4, DISPLAYPORT 2,
3D, EYE. PIP and SWAP.
Remote control bottom
Pic Mute
OPEN CLOSE
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
DisplayPort1 HD-T 3GSDI
VGA COMP1 COMP2
HDMI3
TEST
HDMI4
DisplayPort2
R G B ALL
3D EYE PIP SWAP
456
7 8 9 0
ALT
ADDR
OSD
OFF ON
DEFAULT
FREEZE RE-SYNC
A B C D
USER PRESET
24
19
20
18
21
22
23
Pic Mute
OPEN CLOSE
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
DisplayPort1 HD-T 3GSDI
VGA COMP1 COMP2
HDMI3
TEST
HDMI4
DisplayPort2
R G B ALL
3D EYE PIP SWAP
456
7 8 9 0
ALT
ADDR
OSD
OFF ON
DEFAULT
FREEZE RE-SYNC
A B C D
USER PRESET
Remote control top

page 11
Digital Projection E-Vision Laser WQ120 Series
Installation and Quick-Start Guide
REMOTE CONTROL
Rev A May 2018
Infrared reception
The projector has infrared sensors at the front and back.
The angle of acceptance is 40°. Make sure that the remote control is within the angle of acceptance
when trying to control the projector.
Notes
40°
40°
Infrared reception

page 12
Digital Projection E-Vision Laser WQ120 Series
Installation and Quick-Start Guide
POSITIONING THE SCREEN AND PROJECTOR
Rev A May 2018
Positioning The Screen And Projector
1. Install the screen, ensuring that it is in the best position for viewing by your audience.
2. Mount the projector, ensuring that it is at a suitable distance from the screen for the image to ll the screen. Set the adjustable feet so that
the projector is level, and perpendicular to the screen.
The drawing below shows the positions of the feet for table mounting, and the xing holes for ceiling mounting.
1Four adjustable feet
2Six M4 holes for ceiling mount
The screws should not penetrate more than 15 mm into the body of the projector.
Notes
Always allow the projector
to cool for 5 minutes before
disconnecting the power or
moving the projector.
Ensure that there is at least 50
cm (19.7 in) of space between the
ventilation outlets and any wall,
and 30 cm (11.8 in) on all other
sides.
1
2
1
1
1
2
2
2
2
2

page 13
Digital Projection E-Vision Laser WQ120 Series
Installation and Quick-Start Guide
POSITIONING THE SCREEN AND PROJECTOR
Rev A May 2018
Roll and pitch
The projector can be operated in numerous positions.
In portrait mode, it is recommended to position the projector with inputs facing upward, as shown in the diagram.
1Recommended positions: inputs side up
2Also possible
Notes
Pitch
360° 2
30°
330° 2
1
Roll

page 14
Digital Projection E-Vision Laser WQ120 Series
Installation and Quick-Start Guide
CHANGING THE LENS
Rev A May 2018
Changing The Lens
Inserting a new lens
1. Remove the front and rear lens caps.
2. Position the lens so that the labels are at the top, and gently insert
it all the way into the lens mount.
3. Push the lens in rmly and turn it clockwise until it clicks into place.
Removing the lens
1. Push in the lens release lever, and turn the lens anti-clockwise.
2. Remove the lens.
Notes
Before changing the lens,
always make sure the projector
isswitchedo󰀨andfully
disconnected from its power
supply.
When changing the lens, avoid
using excessive force as this may
damage the equipment.
The lens is shipped separately.
Take care to preserve the original
lens packaging and protective caps
for future use.
The projector will not power on
without the lens tted.