TOYODA TUNNEL SHAKER 32 User manual

MANUAL
DTF-TUNNEL
1. Module one. Manual mode
1.1. Dusting Function
1.2. Shaking Function
1.3. Fan Function
1.4. Paper Feeding Function
1.5. Heating Mode
1.5.1. Smoke Purifier Purifier
1.6. Paper Take-up Function
2. Module Two. Instructions for Using the Auto Mode
3. Module Three. Adjustable Parameter
4. Module Four. Other Design Specifications
5. Maintenance
5.1. Filter Change
5.2. Cleaning
2
2
3
3
4
4
5
6
7
7
8
9
9
10
TABLE OF CONTENTS
Toyoda Tunnel
Powder Applicator
and Dryer (32”)

The powder box is equipped with a heating tube, which is automatically energised when the
machine is switched on to keep the hot melt powder dry.
When using auto mode, the front sensor detects the film and is activated to start automatic
powdering until the weight parameter of the hot melt powder reaches 80 or more. Press Pow-
dering once more to switch off the function.
When using Link mode, the dusting function stops working.
Note *①: Link mode is used for the machine to automatically process the printed pattern until
the end of the film.
1. MODULE ONE. MANUAL MODE
1.1 DUSTING FUNCTION
2

When using the manual mode,
the shaking function is activated
and the shaking paddle removes
excess hot melt powder from the
film at a extremely high frequency,
pressing shaking again will stop
the function.
The shaking function continues to
work when using Link mode.
Press shaking again to turn the
function off.
When using the manual mode,
the vacuum roller function is
activated, attaching the film to the
Vacuum roller, pressing Fan once
more this function will stop being
used.
When using Link mode The
suction roller function continues to
work. Press Fan again to switch
off this function.
1.2. SHAKING FUNCTION
1.3. FAN FUNCTION
3

When using the manual mode, pressing Feeding will activate the function and feed the film into
the oven at an even speed, ensuring that every inch of the pattern is heated evenly. Pressing
Feeding again will deactivate the function.
To operate in Auto mode, two criteria must be met :
1. The Powder value must be displayed as 60 or higher.
2. 2. The front sensor must detect the membrane.
*When using the Link mode, the Shake Powder function continues to operate. Press Feeding
again to turn off this function.
1.4. PAPER FEEDING FUNCTION
When using the manual mode, the mesh belt heating function will be automatically activated to
uniformly bake the film as it moves at a constant speed into the oven, ensuring that every inch
of the pattern is evenly heated. Press Feeding again to turn off this function.
1.5. HEATING MODE
4

After activating Heating, the front preheating plate heating function will automatically turn on.
This smoke cleaning function is automatically activated when Heating is switched on
When using the Link mode, the heating function continues to operate. Press Heating again to
turn off this function.
1.5.1 HEATING MODE
5

In manual mode, the roll function is activated, requiring the user to wrap the baked film from
the bottom of the tension bar to the winding axis and secure the film with tape. The machine
controls the speed of the winding according to the tension sensor.
When using the Link mode, the take-up reel will regularly rotate at timed intervals, and the
vacuum rear panel will open to maintain tension on the film.
1.6. PAPER TAKE-UP FUNCTION
6

When the film hanging from the printer is approximately 60cm long, open the 'Fan' function in
advance and thread the film through above the front preheating plate then placing it on the
vacuum roller. Then press 'Powdering'. When the weight parameter for the hot melt powder
reaches 100, the 'Auto' mode of the powder shaker machine can be operated.
2. MODULE TWO. INSTRUCTIONS FOR
USING THE AUTO MODE.
Shaking Strength: Adjust the frequency of the Shake Powder blade rotation.
Heat Temperature: Adjust the temperature of the dryer.
Feed Speed: Adjust the speed of the mesh belt paper take-up.
Pre Temperature: Adjust the temperature of the front preheating plate.
Roll Interval: Adjust the working Interval of the suction drum.
Smoke : Adjust the size of the air purifier's fan.
3. MODULE THREE. ADJUSTABLE
PARAMETER.
7

Limiting the fall of hot melt powder by adjusting the width of the there two parts.
4. MODULE FOUR. OTHER DESIGN
SPECIFICATIONS.
8

Change the shaker filters every 3-4 months or if you see or smell smoke to ensure proper
airflow and maintenance (based on a 8-9 hours a day of usage).
These are located on the left side of the shaker. Pull open the door and you will see a panel.
Unscrew the panel and you will see the filters. (see attachments)
5.1. MAINTENANCE - FILTER CHANGE
Hinges Are On
This Side
Swing Open
From This Side
9

Lift shaker hood and wipe down the inside border of the lid with a dry cloth to ensure no buildup
of powder. This should be done daily or as needed.
5.2. MAINTENANCE - CLEANING
10

On the left side of the shaker, pull open the door and wipe down these 5 openings. This should
be done daily or as needed.
As the door is opened for daily maintenance, check this opening for a build-up of oil. Oil should
be drained into a bucket through the spout if you see any build-up. This residue is not drain safe
and should be disposed of in cooperation with your local environmental guidelines.
5.2. MAINTENANCE - CLEANING
11