Toyomi BLC 4695 User manual

COOKING BLENDER
MODEL: BLC 4695
220-240V~50/60Hz
Motor power: 1000 W, Heating power: 800 W
SERVICE & IMPORTANT NOTICE
=If the supply cord is damaged, it must be replaced by the manufacturer or its
service agent or a similarity qualified person in order to avoid a hazard.
=WARNING: This appliance is not intended for use by persons (including
children) with reduce physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their
safety.
INSTRUCTION MANUAL
Please read carefully and keep the instruction well

Fruit Juice
Soya
Bean
Multigrain
Porridge
Pureed
Soup Smoothies
PRESET SPEED TIMER
REHEAT
Porridge Corn
Juice Milk
shake
Brush
Cleaning Sponge
Measuring cup
Lid cup
Lid
Blender jug
with heating
element
Motor coupling
Motor Body
Control Panel
Rotary Knob
and start button
O
F
/
F
N
O




Thank you for purchasing our products.
Please read the instructions carefully before use and keep for future reference.
Important
• This appliance is intended for household use only.
• Do not misuse the appliance, do not dismantle, repair or unauthorise alteration to avoid potential injury.
• Do not immerse the appliance in water or any other liquid.
• Place the appliance on a flat, stable, heat-resistant surface away from sources of heat or water splashes.
Warning
• This appliance is not intended for use by persons (including children) with reduce physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
• Do not touch the sharp blades when the appliance is plugged in. If the blades get stuck, unplug the appliance before you
remove the ingredients. Be careful when handling the sharp cutting blades, emptying the bowl and during cleaning.
• Do not touch socket or plug with wet hands to prevent electric shock.
• While blending hot liquid, please make sure the cover lid is close tightly, do not touch the glass jug while is hot to prevent
scalding
• Operate the blender on a flat, stable, heat resistance surface. Do not place any towel, plastic cover under the blender.
• Never use any accessories or parts from other manufacturers which may be hazardous.
• Beware, the appliance releases steam which can cause burns. Handle the lid and cup carefully.
• Do not place glass jug into disinfection appliances or dish-washer machine to prevent damage to the parts.
Caution
• Check that the power supply voltage corresponds to that shown on the appliance
• If using the appliances other than in Singapore, make sure the voltage is the same as stated.
• Switch off and unplug the appliance from the power supply before removing it from the stand, changing accessories or
parts that move in use, during assembling, disassembling or cleaning it.
• If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its
service agent.
• If the blades get stuck, unplug the appliance before you remove the ingredients. Be careful when handling the sharp cutting
blades, emptying the bowl and during cleaning.
• Always make sure the lid is properly closed/assembled on the jar and the lid cup is inserted properly in the lid before you
switch on the appliance.

Function
Soymilk
Porridge
Soup
Smoothies
Juice
Milkshake
Corn Juice
Baby food
Ingredients
⅘cup of soya bean (approx. 90g), water approx. 1000ml
½cup of rice (approx. 50g), read bean (20g), water approx. 1000ml
Pumpkin 150g, Cashew nuts 20g, Brown rice half cup, water 1000ml
Ice 30x30x20mm 8pcs
Fruits up to 1750ml
3cups of corn (approx. 300g) water approx. 1000ml
⅘cup of rice (approx. 90g), water approx. 1000ml
Eg. Carrot juice (carrot 950g+water750ml, set the highest speed)
Timing
28 mins
20mins
25 mins
48 secs
70 secs
21 mins
17 mins
2 mins
Fruit Juice
Soya
Bean
Multigrain
Porridge
Pureed
Soup Smoothies
PRESET SPEED TIMER REHEAT
Porridge Corn
Juice Milk
shake
O
F
/
F
N
O




·Ensures that you can only switch on the appliance if the blender jar is assembled on the motor unit properly. If
the blender jar is not place properly, the machine will not start to blend.
·Do not add ingredients while blending hot preparations as this may cause risk of splashing
·Do not remove the lid cap from the lid during hot preparations, it can reach high temperature and cause burns.
·During the process of heating porridge or soybean milk, if you stop or if there is power failure, do not continue
heating with the remaining food. It may burn the food at the bottom of the heating plate and cause damage to
the appliance. Remove the food and replace with new ingredients.
·When blending is complete, make sure the cutter blades stops before lifting up the glass jug.
·Operating timing: Ensure to follow the operating time as each function has a default timing.
·Boil-dry protection: This appliance is equipped with a boil-dry protection. It switches off automatically if the
appliance is too hot from long usage or if there is not enough liquid. Unplug the appliance let it cool down for 30
mins. Reconnect the appliance to the power supply and resume blending.
·Do not exceed the maximum indication on the blender jar.

1.Power On: Once on power all indicators will light up for 1 second.
2.Standby mode: LED indicator will show “00:00”, other light indicators will be off.
3.Function Selections: Turn the rotary knob to choose the desired function, the chosen function light
indicator will blink and the LED indicator will show “0:00”.
4.During Operation: The chosen function indicator will stay on, the LED indicator will show the
current temperature of the food and will change to indicate heating up. Once it reaches 100°C the
display will change to countdown timing. The first number (in red) indicate the current speed using
and the last 3 digits indicate the countdown timer.
5.After Operation: Once the food is ready, the LED indicator will show “END”.
6.Error Mode: If any error happens, the LED indicator will show an Error code.
7.Start/Cancel button:
Start/Cancel Function: During standby mode, pressing the Start/Cancel button will not have any
effect.
Only during the selection function operating time, press Start/Cancel button to stop all operation and
back to standby mode. All functions are unable to change during operation only Start/Cancel button
can be activated.
·Setting Preset mode: Default timer is 10 mins indicator shows “0:10”, preset button light will blink
and the selection function light will be on. Turn the rotary knob clockwise or anti-clockwise to
increase or decrease the timer by 10 mins per turn. Preset timer is from 0:10 up to 9:50, after 9:50 it
will go back to 0:10.
·During Preset mode: LED indicator will show the timer, timer countdown by 1 min. Preset button and
function button will be lit up.
11.Speed Function: On Standby mode, press the speed button, turn the rotary knob clockwise or
anti-clockwise to change the speed from 1 – H. The first Red digit from the LED indicator is the
current speed chosen.
12.Timer Function: On Standby mode, press the Timer function, turn the rotary knob to change the
operating timing. Turn rotary knob in clockwise or anti-clockwise direction to change the timer by 5
sec per turn. Timer range from 0:05 to 6:00, maximum timer to blend is 6 mins.
13.Procedure for Speed and Timer:
·Only can be set on standby mode.
·These two functions can be use at the same time, press either one function first and adjust the
desire time and speed. No definite sequence for both settings.
·Once setting is done, press the Start/Cancel button to start the operation.
·After setting the timer & speed if Start/Cancel button is not pressed after 10 secs it will go back to
standby mode.
Operating procedure
1. Cut ingredients into 2cm small cubes. (Fig 1)
2. Using the measuring cup for ingredients depending on your recipes. (Fig 2)
3. Pour all ingredients into the Glass Jug. Make sure there is no other residue in the jug. (Fig 3)
4. Add water or other liquid only up to the maximum level or amount depends on the recipes.
5. Place the lid and lock securely. (It will not work if the cover is not securely lock, an error code
E01 will show). See figure 4 the way to lock the cover.
6. Place the jug onto the blender motor body at the right position. (fig 5 & 6)
7. Once everything is place properly, on the power, there will be a beep sound, all indicator light
will light up for 1 sec and go off with only the LED light show 00:00.
1.Turn the rotary button to selection function in “Soymilk” “ Porridge” “Soup” “Smoothies” “ Juice”
“Milkshake” “Corn J” “Baby food” sequence. After choosing the desire function press the
“Start/Cancel” to active the function. The chosen function light will stay on.
Note: Count down timing will activate for all functions, for selected with heating function it will boil the
food till 100°C and starts to countdown till the process is over. For “Smoothies”, “Juice” and
“Milkshake” it will countdown the process without heating up. After all process, it will have 5 beep
sound and the LED indicator will show “END”.
2.After all process, it will have 5 beep sound and the LED indicator will show “END”. (only by
pressing the Start/Cancel button then it will go back to standby mode).
During the operating process, if there is any current interruption within 30 secs, you may continue
with the process. After more than 30 secs, the blender will go back to standby mode and we suggest
to change the ingredients and restart again.
3.After food is ready, turn off the power and unplug the power point, turn the lid anti-clockwise by the
side lever and push up the lid slowly. (If using heating function, please be aware that the lid and the
blender jar will be hot after cooking. Be aware of the steam release when you lift the lid and
measuring cup. (Fig 7)
4.Pour out the food slowly, add any flavouring and ready to be serve. (Fig 8)
5.Wash the blender after it has cooled down, do not leave the food inside the jug too long as you may
have difficulties in cleaning. After cleaning, wipe with a dry cloth.
6.Clean the Motor body with a cloth and let all parts to dry before keeping in the packaging box or
cabinet. (Do not touch the motor coupling immediately after operating as the area may be still hot)
Note:
1.For cooking porridge, puree, soya bean or sticky food, make sure to choose the right function or it
may cause bad taste, uncooked or burnt to the food. Do not add sugar before or during the cooking
process as it may cause lots of foaming and cause spillage.
2.Press the Start/Cancel button if the wrong function is selected, if the food/ liquid inside is not hot
you may reselect the right function and press Start/Cancel button again. If the food/liquid is still hot
around 70-80°C, let it cool down for few mins then restart again.
3.Amount of food or water may follow according to own recipes. For heating function (hot food), do
not exceed 1400ml (Except for Soya Bean function, do not exceed 1200ml), Fruit Juice, Milkshake or
Smoothies must not exceed 1750ml.
4.For blending vegetables or Fruit juice, make sure to remove the seeds before placing into the jug.
5.Do not use this blender to reheat cooked soya bean, Milk, porridge or sticky food as it may get
burnt and damage the heating element.
6.Do not let the appliance run for more than 5 minutes at a time. Let the appliance cool down to room
temperature before you continue processing.
7.If food is burnt and stuck on the heating element, do not use any metallic or sharp-edged utensils
on the unit to avoid scratching on the surface. The best way is to soak it with some hot water for 2
hours and clean it with the cleaning brush.
Cleaning & Maintenance
1.Please off and unplug the power before cleaning.
2.Do not touch the heating element, motor coupling and blade unit after use. Let it cool down before
cleaning
3.Careful of the sharp blade while washing.
4.Do not use abrasive chemical or alcohol to clean the appliance.
5.Do not use any metallic or sharp-edged utensils to avoid scratching on the surface.
6.Do not immerse the glass jug, motor body or power cord in water.
7.Do not rinse the whole glass jug, motor body under running water. Only fill and rinse the inner glass
jug under running water avoid other parts.
8.After cleaning, wipe with a dry cloth and air dry it.
9.Do not place the appliance under the sun to dry.
10.If there are still some stains, fill in some water into the jug and soak for 1-2 hours, after that
slightly scrub away with the brush.
11.For stubborn stains like limescale or brown patches, you may add some lemon or vinegar and
soak for a while and clean it off with a sponge or brush.

Troubleshoot
Problems Causes Solutions
Indicator does not light up The plug is not connected
The glass jug is not position properly to the motor unit
The lid is not securely locked
Check the plug, make sure it is plug properly
Please sure glass jug is properly position to the motor
unit
Make sure the lid is lock at the right position
Indicator lights up,
appliance is not working
Glass Jug has no water
Appliance has alarm beeping
Add water to the glass jug
Unplug the appliance, wait for 1 minute and plug in
again
Temperature sensor not detected The glass jug is not positioned properly
Send to service centre
Temperature sensor is faulty Send to service centre
Appliances is overloaded or overheating
Current voltage is lower than 160V Check local current should be 220-240V
Current voltage is higher than 270V Check local current should be 220-240V
Appliances is malfunction Send to service centre
No respond when pressing
function or any button
Boil dry function may be activated
It is normal
Selected function is activated
Food does not blend well Water is too much or less
Current power is lower
Pieces of food is too large, hard or too much
Please add appropriate water amount
Use the right current for this appliance.
Please follow instruction manual for the recipes or
reduce the size and quantity of ingredients processed.
Appliances is malfunction Send to service centre
Food not heating up or not
cooked
Water is too much or less Please add appropriate water amount according to
recipes
Food burnt The heating element is not clean with balance residue
Ingredients is too much
Chosen wrong function
Clean the heating element thoroughly before using
Please follow instruction manual for the recipes or
reduce the size and quantity of ingredients processed
Choose the right function
The blade does not turn Pieces of food is too large, hard or too much
Selected wrong speed to blend
Appliances is malfunction
Reduce the size or quantity of ingredients processed.
Adjust to the higher speed
Send to service centre
Abnormal Sound when
operating
The glass jug is not position properly to the motor unit
Some food sticks on the blade or the Jug
Appliance is malfunctioned Clear the excess food
Send to service centre