TP-Link TF-3239DL User manual

2
ØSupports ACPI, PCI power management
ØComplies with the IEEE802.3u Fast Ethernet, 100Base-TX
standard and IEEE802.3 CSMA/CD 10Base-T standard
ØSupports Full Duplex Flow Control (IEEE 802.3x)
ØFull duplex design to double the performance
ØSupportsAuto-Negotiationfunction
ØAuto-setups IRQ and I/O address
ØContains two large (2Kbyte) independent receive and transmit
FIFOs
ØOne STP/UTP connector for 10Mbps or 100Mbps network Speed
ØProvides diagnostic software and one LED to indicate network
Link/activity
ØSupports smart remote boot ROM and provides the help for
RPL/PXE(Exclude TF-3239DL)
ØSupports ODI Driver for NetWare 3.x, 4.x, NDIS Driver for LAN
Manager, Windows 95, Windows NT, Windows 2000, Packet
driver forTCP/IP
Chapter 2 Installation
Card Installation
To insert The Product into your computer, follow the steps list below.
1 Turn off the computer and remove its cover.
2 Insert The Product into a PCI slot.
3 Secure the Product to the rear of the computer chassis and put
back the computer cover.
4 Connect the Product to the network using twisted-pair cables.
Driver Installation
Use the drivers supplied by the diskette included in The Product. For
detail description, please refer to "help" in the diskette provided by the
Product.
Appendix A: Troubleshooting
If you experience any problems with the adapter, first make sure the
appropriate driver is loaded, the proper cable is connected to the
adapter port and the hub complies with the adapter specification, such
as 10Mbps 10Base-T or 100Mbps 100Base-TX. Then recheck the LED.
The Product provided one LEDs to indicate network status.
LINK/ACTIVE LED
A red LED indicates if the 10 or 100Mbps STP/UTP has been link OK or
not and is working or not. When the light is OFF, it indicates that the
STP/UTP port has not been connected or link not OK; When the light
is ON, it indicates that the STP/UTP port link OK. When the light is
BLINKING, it indicates that the STP/UTP port is receiving data or
transmitting data.
Appendix B: Technical Specification
Topology: Star
Connector Supported: RJ45
Standard: IEEE802.3 10Base-T
IEEE802.3u100Base-TX
Transmission Rate: 100Mbps or 200Mbps
Hardware: IBM PC compatibles(It must have PCI slot)
IRQ Line: Assigned by system
I/OAddress: Assignedbysystem
Software: ODI driver for NetWare 3.x, 4.x, NDIS driver for Microsoft
LAN manager and Windows 98, Windows ME, Windows NT, Windows
2000 Packet driver for TCP/IP
oo
Temperature: 0 C to 40 C (Operating)
Humidity: 5% to 95% (Non-condensing)
Power consumption: 1W(Max)
Appendix C: Contact Information
TP-LINK TECHNOLOGIES CO., LTD.
For help with the installation or operation of the TP-LINK TF-3239D/
TF-3239DL Adapter, please contact us.
Add: Fl.3, Bldg.R1-B, High-Tech Industrial Park, Shennan Road,
Shenzhen, China
E-mail: [email protected]
Website: http://www.tp-link.com
43 5
User's Guide
10/100M Fast Ethernet Adapter
TF-3239D/TF-3239DL
71030429
Made in China
Ver: 2.0

1 2
Thank you for purchasing TF-3239 series 10/100M Fast Ethernet
Adapters. This guide is to provide the installation and usage of the
Products for network installers or users. The Product complies with
PCI 2.1/2.2 specification and supports half/full duplex feature which
can double network speed.
The Adapters support both 10Mbps and 100Mbps network speed,
100Base-TX operates on twisted pairs of Category 5 UTP and 10Base-
T operates on Category 3, 4, 5 UTP. The Products use Auto-
Negotiation technology to detect the network speed. Extensive driver
supports for including commonly used network operation system
Netware, Win9x,Win2000, Windows NT, and TCP/IPare available.
This manual is divided into two chapters and two appendices. The
following summarizes the contents of the chapters and appendices.
Chapter 1 Introduction
Hardware Overview
TF-3239 series Adapters are highly integrated and cost-effective
single-chip Fast Ethernet Adapter that provides 32-bit performance,
PCI bus master capability, and full compliance with IEEE 802.3u
100Base-TX specifications and IEEE 802.3x Full Duplex Flow Control.
They also support ACPI, PCI power management for modern
operating systems that is capable of Operating System Directed Power
Management (OSPM) to achieve the most efficient power
management.
The Adapters keep network maintenance cost low and eliminate usage
barriers. It is the easiest way to upgrade a network from 10 to 100Mbps.
The product is highly integrated and requires no "glue" logic or external
memory.
It includes an interface for a boot ROM and can be used in diskless
workstations, providing maximum network security and ease of
management(Exclude TF-3239DL).
They also support full-duplex operation, making possible 200Mbps of
bandwidth at no additional cost. The Adapters support both 10Mbps
and 100Mbps network speed, 100Base-TX operate on twisted pairs of
Category 5 UTP and 10Base-T operate on Category 3, 4, 5 UTP. The
Adapters use Auto-Negotiation technology to detect the network speed.
Extensive driver supports for including commonly used network
operation system Netware, Win9x,Win2000, Windows NT, and TCP/IP
are available.
Whatever your requirements are ease of installation, superior
performance, or responsive support backed up by unlimited technical
support, the Product is the superior choice.
Features & Benefits
ØIntegrated Ethernet MAC, Physical chip and transceiver in one
chip
ØCompliant to PCI Revision 2.1/2.2
ØPCI local bus single-chip Ethernet controller
ØSupports PCI clock 16.75MHz-40MHz
ØSupports a 32-bit general-purpose timer, referenced by the
external PCI clock source, and timer-interrupt
ØIncludes a programmable, PCI burst size and early Tx/Rx
threshold
ØSupports PCI target fast back-to-back transaction
ØSupports digital and analog loopback capability on both ports
FCC STATEMENT
The adapter has been tested and found to comply with the limits for
a class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
ØReorient or relocate the receiving antenna.
ØIncrease the separation between the equipment and receiver.
COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a
registered trademark of TP-LINK Technologies Co., Ltd. Other
brands and product names are trademarks or registered trademarks
of their respective holders.
No part of the specifications may be reproduced in any form or by
any means or used to make any derivative such as translation,
transformation, or adaptation without permission from TP-LINK
Technologies Co., Ltd. Copyright ©2005 TP-LINK Technologies Co.,
Ltd. All rights reserved.
ØConsult the dealer or an experienced radio/TV technician for
help.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
interference that may cause undesired operation.
EC DECLARATION OF CONFORMITY (EUROPE)
In compliance with the EMC Directive 89/336/EEC, the adapter
meets the requirements of the following standards:
ØEN55022
ØEN55024
SAFETY NOTICES
Caution:
Do not use this product near water, for example, in a wet basement
or near a swimming pool.
Avoid using this product during an electrical storm. There may be a
remote risk of electric shock from lightning.