TP-Link TL-WR841HP User manual

300Mbps High Power Router
REV1.0.0
1910010810

COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered trademark
of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or
registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to make any
derivative such as translation, transformation, or adaptation without permission from TP-LINK
TECHNOLOGIES CO., LTD. Copyright © 2013 TP-LINK TECHNOLOGIES CO., LTD. All rights
reserved.
http://www.tp-link.com

FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
•Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s authority
to operate the equipment.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This device and its antenna must not be co-located or operating in conjunction with
any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, this grant is applicable to only
Mobile Configurations. The antennas used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter.”

This is a class B product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
Canadian Compliance Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject
to the following two conditions:
(1)This device may not cause interference, and
(2)This device must accept any interference, including interference that may cause undesired
operation of the device.
Cet appareil est conforme aux norms CNR exemptes de licence d’Industrie Canada. Le
fonctionnement est soumis aux deux conditions suivantes:
(1)cet appareil ne doit pas provoquer d’interférences et
(2)cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer un
fonctionnement non souhaité de l’appareil.
Industry Canada Statement
Complies with the Canadian ICES-003 Class B specifications.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
This device complies with RSS 210 of Industry Canada. This Class B device meets all the
requirements of the Canadian interference-causing equipment regulations.
Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.
Korea Warning Statements
당해 무선설비는 운용중 전파혼신 가능성이 있음.

NCC Notice & BSMI Notice
注意！
依據 低功率電波輻射性電機管理辦法
第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、
加大功率或變更原設計之特性或功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通行；經發現有干擾現象時，應立即
停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電信。低功率射
頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам
нормативних документів та вимогам, що передбачені чинними законодавчими актами
України.
Safety Information
When product has power button, the power button is one of the way to shut off the product;
when there is no power button, the only way to completely shut off power is to disconnect the
product or the power adapter from the power source.
Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock and
voiding the limited warranty. If you need service, please contact us.
Avoid water and wet locations.
This product can be used in the following countries:
AT BG BY CA CZ DE DK EE
ES FI FR GB GR HU IE IT
LT LV MT NL NO PL PT RO
RU SE SK TR UA

TP-LINK TECHNOLOGIES CO., LTD
TP-LINK TECHNOLOGIES CO., LTD.
Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park,
Shennan Rd, Nanshan, Shenzhen, China
DECLARATION OF CONFORMITY
For the following equipment:
Product Description: 300Mbps High Power Router
Model No.: TL-WR841HP
Trademark: TP-LINK
We declare under our own responsibility that the above products satisfy all the technical
regulations applicable to the product within the scope of Council Directives:
Directives 1999/5/EC, Directives 2004/108/EC, Directives 2006/95/EC, Directives 1999/519/EC,
Directives 2011/65/EU
The above product is in conformity with the following standards or other normative documents
ETSI EN 300 328 V1.7.1: 2006
ETSI EN 301 489-1 V1.9.2:2011& ETSI EN 301 489-17 V2.1.1:2009
EN 55022:2010
EN 55024:2010
EN 61000-3-2:2006+A1:2009+A2:2009
EN 61000-3-3:2008
EN 60950-1:2006+A11：2009+A1:2010+A12:2011
EN 62311:2008
The product carries the CE Mark:
Person responsible for marking this declaration:
Yang Hongliang
Product Manager of International Business
Date of issue:2013

- I -
CONTENTS
Package Contents........................................................................................................ 1
Chapter 1. Introduction ........................................................................................... 2
1.1 Overview of the Router .................................................................................................2
1.2 Conventions ..................................................................................................................3
1.3 Main Features ...............................................................................................................3
1.4 Panel Layout .................................................................................................................4
1.4.1 The Front Panel ................................................................................................4
1.4.2 The Rear Panel.................................................................................................5
Chapter 2. Connecting the Router ......................................................................... 6
2.1 System Requirements...................................................................................................6
2.2 Installation Environment Requirements........................................................................6
2.3 Connecting the Router..................................................................................................6
Chapter 3. Quick Installation Guide....................................................................... 8
3.1 TCP/IP Configuration ....................................................................................................8
3.2 Quick Installation Guide..............................................................................................10
Chapter 4. Configuring the Router ...................................................................... 16
4.1 Login ...........................................................................................................................16
4.2 Status ..........................................................................................................................16
4.3 Quick Setup ................................................................................................................17
4.4 WPS............................................................................................................................17
4.5 Network .......................................................................................................................20
4.5.1 WAN................................................................................................................20
4.5.2 LAN .................................................................................................................30
4.5.3 MAC Clone......................................................................................................30
4.6 Wireless ......................................................................................................................31
4.6.1 Wireless Settings ............................................................................................31
4.6.2 Wireless Security ............................................................................................34
4.6.3 Wireless MAC Filtering ...................................................................................37
4.6.4 Wireless Advanced .........................................................................................39
4.6.5 Wireless Statistics...........................................................................................41
4.7 DHCP ..........................................................................................................................41
4.7.1 DHCP Settings ................................................................................................42

- II -
4.7.2 DHCP Client List .............................................................................................43
4.7.3 Address Reservation ......................................................................................43
4.8 Forwarding ..................................................................................................................44
4.8.1 Virtual Servers ................................................................................................44
4.8.2 Port Triggering ................................................................................................46
4.8.3 DMZ ................................................................................................................48
4.8.4 UPnP...............................................................................................................49
4.9 Security .......................................................................................................................50
4.9.1 Basic Security .................................................................................................50
4.9.2 Advanced Security..........................................................................................51
4.9.3 Local Management .........................................................................................53
4.9.4 Remote Management .....................................................................................54
4.10 Parental Control ..........................................................................................................55
4.11 Access Control............................................................................................................57
4.11.1 Rule.................................................................................................................57
4.11.2 Host.................................................................................................................63
4.11.3 Target ..............................................................................................................64
4.11.4 Schedule .........................................................................................................67
4.12 Advanced Routing.......................................................................................................68
4.12.1 Static Routing..................................................................................................69
4.12.2 System Routing Table .....................................................................................70
4.13 Bandwidth Control.......................................................................................................70
4.13.1 Control Settings ..............................................................................................71
4.13.2 Rules List ........................................................................................................71
4.14 IP & MAC Binding Setting...........................................................................................72
4.14.1 Binding Settings ..............................................................................................72
4.14.2 ARP List ..........................................................................................................74
4.15 Dynamic DNS .............................................................................................................75
4.15.1 Comexe.cn DDNS...........................................................................................75
4.15.2 Dyndns.org DDNS ..........................................................................................76
4.15.3 No-ip.com DDNS ............................................................................................77
4.16 System Tools...............................................................................................................78
4.16.1 Time Settings ..................................................................................................78
4.16.2 Diagnostic .......................................................................................................80
4.16.3 Firmware Upgrade ..........................................................................................82
4.16.4 Factory Defaults..............................................................................................83

- III -
4.16.5 Backup & Restore ...........................................................................................83
4.16.6 Reboot.............................................................................................................84
4.16.7 Password ........................................................................................................85
4.16.8 System Log .....................................................................................................85
4.16.9 Statistics..........................................................................................................87
Appendix A: FAQ ....................................................................................................... 90
Appendix B: Configuring the PC ............................................................................. 95
Appendix C: Specifications...................................................................................... 99
Appendix D: Glossary ............................................................................................. 100

TL-WR841HP
300Mbps High Power Router User Guide
- 1 -
Package Contents
The following items should be found in your package:
TL-WR841HP 300Mbps High Power Router
Power Adapter for TL-WR841HP 300Mbps High Power Router
Quick Installation Guide
Resource CD for TL-WR841HP 300Mbps High Power Router, including:
•This Guide
•Other Helpful Information
Note:
Make sure that the package contains the above items. If any of the listed items are damaged or
missing, please contact your distributor.

TL-WR841HP
300Mbps High Power Router User Guide
- 2 -
Chapter 1. Introduction
1.1 Overview of the Router
The TL-WR841HP 300Mbps High Power Router integrates 4-port Switch, Firewall, NAT-Router and
Wireless AP. Powered by 2x2 MIMO technology, the 300Mbps High Power Router delivers
exceptional range and speed, which can fully meet the need of Small Office/Home Office (SOHO)
networks and the users demanding higher networking performance.
The TL-WR841HP 300Mbps High Power Router provides up to 300Mbps wireless connection with
other 802.11n wireless clients. The incredible speed makes it ideal for handling multiple data streams
at the same time, which ensures your network stable and smooth. The performance of this 802.11n
wireless Router will give you the unexpected networking experience at speed much faster than
802.11g. It is also compatible with all IEEE 802.11g and IEEE 802.11b products.
With multiple protection measures, including SSID broadcast control and wireless LAN
64/128/152-bit WEP encryption, WiFi protected Access (WPA2- PSK, W PA- PSK), as well as
advanced Firewall protections, the TL-WR841HP 300Mbps High Power Router provides complete
data privacy.
The TL-WR841HP 300Mbps High Power Router provi des flexible access control, so that parents or
network administrators can establish restricted access policies for children or staff. It also supports
Virtual Server and DMZ host for Port Triggering, and then the network administrators can manage and
monitor the network in real time with the remote management function.
Since the Router is compatible with virtually all the major operating systems, it is very easy to
manage. Quick Setup Wizard is supported and detailed instructions are provided step by step in
this user guide. Before installing the Router, please look through this guide to know all the
Router’s functions.
Simple Installation
Flexible Access Control
Multiple Security Protections
Incredible Speed

TL-WR841HP
300Mbps High Power Router User Guide
- 3 -
1.2 Conventions
The Router or TL-WR841HP mentioned in this guide stands for TL-WR841HP 300Mbps High Power
Router without any explanation.
1.3 Main Features
Complies with IEEE 802.11n to provide a wireless data rate of up to 300Mbps.
One 10/100M Auto-Negotiation RJ45 WAN port, four 10/100M Auto-Negotiation RJ45 LAN
ports, supporting Auto MDI/MDIX.
Provides W PA/W PA2, W PA-PSK/WPA2-PSK authentication, TKIP/AES encryption security.
Shares data and Internet access for users, supporting Dynamic IP/Static IP/PPPoE Internet
access.
Supports Virtual Server, Special Application and DMZ host.
Supports UPnP, Dynamic DNS, Static Routing.
Provides Automatic-connection and Scheduled Connection on certain time to the Internet
Built-in NAT and DHCP server supporting static IP address distributing.
Supports Parental Control and Access Control.
Connects Internet on demand and disconnects from the Internet when idle for PPPoE.
Provides 64/128/152-bit WEP encryption security and wireless LAN ACL (Access Control
List).
Supports Flow Statistics.
Supports firmware upgrade and Web management.

TL-WR841HP
300Mbps High Power Router User Guide
- 4 -
1.4 Panel Layout
1.4.1 The Front Panel
Figure 1-1 Front Panel
The Router’s LEDs are located on the front panel (View from left to right).
Name Status Indication
（Power）Off Power is off.
On Power is on.
(System) Flashing The Router is working properly.
On/Off The Router has a system error.
(WLAN) Off The Wireless function is disabled.
Flashing The Wireless function is enabled.
(WAN),
(LAN 1-4)
Off There is no device linked to the corresponding port.
On There is a device linked to the corresponding port but
there is no activity.
Flashing There is an active device linked to the corresponding port.
(WPS)
Slow Flash A wireless device is connecting to the network by WPS
function. This process will last in the first 2 minutes.
On A wireless device has been successfully added to the
network by WPS function.
Quick Flash A wireless device failed to be added to the network by
WPS function.
Table 1-1 The LEDs Description
Note:
After a device is successfully added to the network by WPS function, the WPS LED will keep on
for about 5 minutes and then turn off.

TL-WR841HP
300Mbps High Power Router User Guide
- 5 -
1.4.2 The Rear Panel
Figure 1-2 Rear Panel sketch
The following parts are located on the rear panel (View from left to right).
POWER: The Power socket is where you will connect the power adapter. Please use the
power adapter provided with this TL-WR841HP 300Mbps High Power Router.
INTERNET:This port is where you will connect the DSL/cable Modem or Ethernet.
1,2,3,4 (ETHERNET): These ports (1,2,3,4) connect the Router to the local PC(s).
WPS/RESET: This button is used for both WPS and Reset function. To use the WPS
function, press it for less than five seconds; to use the RESET function, press it for more
than five seconds.
Used as RESET button:
There are two ways to reset to the Router's factory defaults:
1) Use the Factory Defaults function on System Tools -> Factory Defaults page in the
Router's Web-based Utility.
2) Use the WPS/RESET button: With the Router powered on, press and hold the
WPS/RESET button (more than 5 seconds) until the SYS LED becomes quick-flash from
slow-flash. Then release the button and wait the Router to reboot to its factory default
settings.
Used as WPS button:
If you have client devices, such as wireless adapters, that support Wi-Fi Protected Setup,
then you can press this button to quickly establish a connection between the Router and
client devices and automatically configure wireless security for your wireless network.
Wireless antenna: To receive and transmit the wireless data.

TL-WR841HP
300Mbps High Power Router User Guide
- 6 -
Chapter 2. Connecting the Router
2.1 System Requirements
Broadband Internet Access Service (DSL/Cable/Ethernet)
One DSL/Cable Modem that has an RJ45 connector (which is not necessary if the Router is
connected directly to the Ethernet.)
PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors
TCP/IP protocol on each PC
Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari
2.2 Installation Environment Requirements
Place the Router in a well ventilated place far from any heater or heating vent
Avoid direct irradiation of any strong light (such as sunlight)
Keep at least 2 inches (5 cm) of clear space around the Router
Operating Temperature: 0℃~40℃ (32℉~104℉)
Operating Humidity: 10%~90%RH, Non-condensing
2.3 Connecting the Router
Before installing the Router, make sure your PC is connected to the Internet through the
broadband service successfully. If there is any problem, please contact your ISP. After that, please
install the Router according to the following steps. Don't forget to pull out the power plug and keep
your hands dry.
1. Power off your PC, Cable/DSL Modem, and the Router.
2. Locate an optimum location for the Router. The best place is usually at the center of your
wireless network.
3. Adjust the direction of the antenna. Normally, upright is a good direction.
4. Connect the PC(s) and each Switch/Hub in your LAN to the LAN Ports on the Router, shown
in Figure 2-1. (If you have the wireless NIC and want to use the wireless function, you can
skip this step.)
5. Connect the DSL/Cable Modem to the INTERNET port on the Router, shown in Figure 2-1.

TL-WR841HP
300Mbps High Power Router User Guide
- 7 -
6. Connect the power adapter to the power socket on the Router, and the other end into an
electrical outlet. The Router will start to work automatically.
7. Power on your PC and Cable/DSL Modem.
Figure 2-1 Hardware Installation of the 300Mbps High Power Router

TL-WR841HP
300Mbps High Power Router User Guide
- 8 -
Chapter 3. Quick Installation Guide
This chapter will show you how to configure the basic functions of your 300Mbps High Power
Router using Quick Setup Wizard within minutes.
3.1 TCP/IP Configuration
The default domain name of the 300Mbps High Power Router is http://tplinklogin.net, the default
IP address is 192.168.0.1, and the default Subnet Mask is 255.255.255.0. These values can be
changed as you desire. In this guide, we use all the default values for description.
Connect the local PC to the LAN ports of the Router. And then you can configure the IP address
for your PC in the following two ways.
Configure the IP address manually
1) Set up the TCP/IP Protocol for your PC. If you need instructions as to how to do this,
please refer to Appendix B: "Configuring the PC".
2) Configure the network parameters. The IP address is 192.168.0.xxx ("xxx" is any number
from 2 to 254), Subnet Mask is 255.255.255.0, and Gateway is 192.168.0.1 (The
Router's default IP address)
Obtain an IP address automatically
1) Set up the TCP/IP Protocol in "Obtain an IP address automatically" mode on your PC.
If you need instructions as to how to do this, please refer to Appendix B: "Configuring the
PC”.
2) Then the built-in DHCP server will assign IP address for the PC.
Now, you can run the Ping command in the command prompt to verify the network connection
between your PC and the Router. The following example is in Windows 2000 OS.
Open a command prompt, and type ping 192.168.0.1, and then press Enter.
If the result displayed is similar to the Figure 3-1, it means the connection between your PC
and the Router has been established well.

TL-WR841HP
300Mbps High Power Router User Guide
- 9 -
Figure 3-1 Success result of Ping command
If the result displayed is similar to the Figure 3-2, it means the connection between your PC
and the Router is failed.
Figure 3-2 Failure result of Ping command
Please check the connection following these steps:
1. Is the connection between your PC and the Router correct?
Note:
The 1/2/3/4 LEDs of LAN ports which you link to on the Router and LEDs on your PC's adapter
should be lit.
2. Is the TCP/IP configuration for your PC correct?
Note:
If the Router's IP address is 192.168.0.1, your PC's IP address must be within the range of
192.168.0.2 ~ 192.168.0.254.

TL-WR841HP
300Mbps High Power Router User Guide
- 10 -
3. Is the default LAN IP of the Router correct?
Note:
If the LAN IP of the modem connected with your router is 192.168.0.x, the default LAN IP of the
Router will automatically switch from 192.168.0.1 to 192.168.1.1 to avoid IP conflict. Therefore, in
order to verify the network connection between your PC and the Router, you can open a
command prompt, and type ping 192.168.1.1, and then press Enter.
3.2 Quick Installation Guide
With a Web-based utility, it is easy to configure and manage the 300Mbps High Power Router.
The Web-based utility can be used on any Windows, Macintosh or UNIX OS with a Web browser,
such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari.
1. To access the configuration utility, open a web-browser and type in the default domain name
http://tplinklogin.net in the address field of the browser.
Figure 3-3 Log in the Router
After a moment, a login window will appear, similar to the Figure 3-4. Enter admin for the
User Name and Password, both in lower case letters. Then click the OK button or press the
Enter ke y.
Figure 3-4 Login Windows
Note:
If the above screen does not pop-up, it means that your Web-browser has been set to a proxy.
Go to Tools menu>Internet Options>Connections>LAN Settings, in the screen that appears,
cancel the Using Proxy checkbox, and click OK to finish it.

TL-WR841HP
300Mbps High Power Router User Guide
- 11 -
1. After successfully log in, you can click the Quick Setup menu to quickly configure your
Router.
Figure 3-5 Quick Setup
2. Click Next, and then WAN Connection Type page will appear, shown in Figure 3-6.
Figure 3-6 WAN Connection Type
The Router provides Auto-Detect function and supports three popular ways PPPoE,
Dynamic IP and Static IP to connect to the Internet. It’s recommended that you make use of
the Auto-Detect function. If you are sure of what kind of connection type your ISP provides,
you can select the very type and click Next to go on configuring.
3. If you select Auto-Detect, the Router will automatically detect the connection type your ISP
provides. Make sure the cable is securely plugged into the WAN port before detection. The
appropriate configuration page will be displayed when an active Internet service is
successfully detected by the Router.
1) If the connection type detected is PPPoE, the next screen will appear as shown in Figure
3-7.