Traeger Silverton TFS62PLD User manual

PLACE INNER GRILL COMPONENTS AND BUCKET
4
ASSEMBLE DOORS AND UPPER GRILL COMPONENTS
3
In this step: 10 15 16
2
1
13
You are ready to season your grill and get Traeger’ing!
Refer to your Use & Care Instructions for operation instructions.
In this step: 6x2
18 Dx 2 Ex2 Hx 2
4 5 6
2
ASSEMBLY
GUIDE
For English-only assistance
with assembly, installation, parts,
and customer service, contact
Traeger's VIP-365 Customer Service.
Phone: 1-800-TRAEGER
Email: [email protected]
Mail: Traeger Pellet Grills LLC
1215 E. Wilmington Ave.
Salt Lake City, UT 84106
traegergrills.com
WARNING!
Many parts of the grill will become very hot during
operation. Care must be taken to avoid burns, both during
operation and afterwards while the grill is still hot.
• Never leave the grill unattended when young children
are present.
• Never move the grill when it is operating.
• Let the grill cool thoroughly before moving or attempting
to transport.
• Grill is very heavy. Always lift grill with TWO people.
A MAJOR CAUSE OF FIRES IS FAILURE
TO MAINTAIN REQUIRED CLEARANCES
(AIR SPACES) TO COMBUSTIBLE
MATERIALS. IT IS OF UTMOST
IMPORTANCE THAT THIS PRODUCT
BE INSTALLED ONLY IN ACCORDANCE
WITH THESE INSTRUCTIONS.
3
In this step: 811 Fx 8
In this step: 13 14
In this step: 12
This will require TWO people.
Wood Fired Grills – Silverton
IMPORTANT, RETAIN FOR FUTURE
REFERENCE: READ CAREFULLY
In this step: 17 Gx 6
Please read this entire manual before installation and use of this pellet
fuel-burning appliance. Failure to follow these instructions could result in property
damage, bodily injury, or even death. Contact your local building or re ofcials
about restrictions and installation inspection requirements in your area.
TFS62PLD

12 in. / 30.5 cm 12 in. / 30.5 cm
4 5
2
2
1
NOTE: Grill is secured in box with multiple cardboard
pieces, some of which hold grill parts. Be sure to check
ALL packaging for parts as you unpack them.
In this step: 14In this step: 9
In this step:
Ax 4 Bx 4 Cx 4
READ ALL INSTRUCTIONS BEFORE INSTALLING
AND USING THE APPLIANCE
BLISTERPACK PARTS NEEDED
Wrench
(2 pcs)
Self-tapping Screw:
#8x0.375" (6 pcs)
G
WARNING!
• When operating this grill under overhead combustibles,
a MINIMUM of 40 in. / 101.6 cm in is required.
• When operating this grill, maintain a MINIMUM distance
of 12 in. / 30.5 cm from the grill to combustibles.
IMPORTANT!
• The grill is very heavy. Always lift the grill with TWO people.
3
UNPACK COMPONENTS
INSTALL LEGS
Bolt: 1/4-20x0.6"
(2 pcs)
E
A
Screw:
1/4-20x0.6" (12 pcs)
Washer: 1/4"
(12 pcs)
C
B
Spring Washer:
1/4" (12 pcs)
NOTE: Legs have a clip feature that matches
up with corresponding slots on the grill body.
Do not fully tighten leg screws at this time.
NOTE: After the bottom shelf
and back are installed, fully
tighten all leg screws (Step 3).
Install the back panel.
NOTE: Some of the parts come with pre-installed fasteners, including:
• Grill door handle (pre-installed on inside of door with bolts
and washers)
PARTS LIST
8
3
11
12
1
10
13
14
15
16
9
Screwdriver
(1 pc)
D
Washer: 1/4"
(2 pcs)
H
Mica Washer:
(2 pcs)
5
2
4
7
6
1
31 2
40 in. / 101.6 cm
Install the bottom shelf.
In this step: In this step:
7Ax 4 Bx 4 Cx 4 5Ax 4 Bx 4 Cx 4
17
F
Stainless Steel Screw:
1/4-20x0.6" (8 pcs)
18