Memphis ELITE VG0002 User manual

CONTENTS
Clearance to Combustibles
2
Wiring Diagram
3-4
MEMPHIS ELITE
MODEL NUMBER
VG0002/VG0002E/VG0002S4/VG00002S4-3

2
YOUR MEMPHIS GRILL MUST MAINTAIN THE
SPECIFIED CLEARANCE TO COMBUSTIBLE
MATERIALS WHILE OPERATING THE GRILL
OR WHILE THE GRILL IS HOT!
Below are some guidelines to ensure safe
operation of your Memphis Grill
The grill is to be supported by the casters provided.
Grill casters are to be locked while the grill is in
use or while the grill is hot.
It is recommended that the grill be placed on a
non-combustible surface.
Operating the grill under a combustible ceiling or
overhang is NOT recommended.
Maintain the minimum clearance to combustible
materials specified below.
A MAJOR CAUSE OF FIRES IS
FAILURE TO MAINTAIN REQUIRED
CLEARANCES (AIR SPACES) TO
COMBUSTIBLE MATERIALS. IT IS OF
THE UTMOST IMPORTANCE THAT
THIS PRODUCT BE INSTALLED ONLY
IN ACCORDANCE WITH THESE
INSTRUCTIONS
CLEARANCE TO
COMBUSTIBLE MATERIALS

3
Item #
NAME
DESCRIPTION
1
USB Port
Used to update your grill, see the “Updating Controller Software” section of the
main manual for information.
2
Meat Probe Wiring
This terminal is used to connect the meat probes to the controller.
3
120/240 Select Jumper
Used when changing the input voltage to the controller, see “120v to 240v
Conversion” section of the main manual for information.
4
AC Load Wire from Filter to
Controller
Carries AC voltage from the filter to the control board, load wire.
5
AC Neutral Wire from Filter to
Controller
Carries AC voltage from the filter to the control board, neutral wire.
6
Filter
Reduces electrical feedback. Line = Outlet Side, Load = Grill Side. L1 = Load L2=
Neutral
7
AC Neutral and Load from IEC to
Filter
A two wire component which has a ferrite choke to eliminate input electrical
disturbances from the grid. Load and Neutral wires.
8
IEC Plug
The same plug terminal used to attach your power cord to your grill. Top down view.
9
Ethernet Cable
Used to connect your grill controller to the Wi-Fi card in the back of the grill.
10
Grounding Wire
In the event your grill experiences a short, the grounding wire will send the voltage
to the 3rd prong of a standard AC outlet.
11
AC Component Wiring
This large plastic connector carries all voltage used for AC components in the grill.
See “Component Wiring Diagram” for a description of all wires in this connector.
12
RTD Wiring (DC)
This small plastic connector carries DC voltage to the RTD.
13
Controller Box Ethernet Cable
Gland
This gland is a weather tight pass-through for the Ethernet cable into the back of
the controller box.
14
Controller Box Plug
This plug is a weather tight quick disconnect for the main wiring harness which
carries all AC,DC, and Ground wires to the grill’s components.
MEMPHIS ELITE CONTROLLER
BOX WIRING DIAGRAM
LOAD
NEUTRAL
GROUND

4
Item #
NAME
Wire Identification
DESCRIPTION / INSTRUCTION
1
Auger Motor
Wiring
1x Black Wire, 1x White Wire
Attach both spade connectors to their respective terminals on the
top of the auger motor as indicated by the arrows shown above.
2
RTD Wiring
1x Orange Wire, 1x Brown Wire
Attach both spade connectors to the leads extending from the RTD
as shown above.
3
Grounding Wire
Green Wire
The connection point for the ground is located directly below the
auger motor on the vertical panel behind the auger motor.
4
Ethernet Cable
Black Cable with Ethernet End
Attach the Ethernet cable to the terminal on the Wi-Fi card as
shown. Ensure that the wiring does not interfere with the auger
motor’s moving components.
5
Igniter Wiring
1x Red Wire, 1x White Wire
Attach both spade connectors to the leads extending from the
igniter. These leads will extend from the airbox and can be located
in between the two fans.
6
Fan Wiring
1x Blue Wire w/ 2 spade ends,
1x White Wire w/ 2 spade ends
Attach BOTH blue spade connectors to 1 fan and then attach the red
spade connectors to the other fan.
MEMPHIS ELITE COMPONENT
WIRING DIAGRAM
NOTE: ALL TWO WIRE PAIRS FOR A SPECIFIC COMPONENT ARE REVERSABLE
Example: The auger motor wiring can have the either spade connector from
its two wire pair attached to either terminal and the motor will function
normally.
RTD
Auger Motor
Igniter
Wi-Fi Card
Fans