TRAK RACER TR80-TMARM4-BLK User manual

1
Published 2023‑09‑06
IMPORTANT: As there are different versions of each rig depending on your
region, please ensure that you are using the correct instruction set. The
part number below should match the part number labeled on your box
Arms for Triple Monitors
with VESA Mounts
Assembly Guide
TR80-TMARM4-BLK

3 Symbol Legend
4 Part list
5 Assembly Notes
9 TR80-TMARM4-BLK Assembly Instructions
2
TABLE OF CONTENTS

3
Two people needed
Tighten hardware
Leave hardware loose for adjustment
Make Adjustment
Break tab off Corner bracket CB1
Safety glasses needed
Attention / Priority
Reserve for following step
Mirrored Components (Same on both sides)
IMPORTANT: As there are different versions of each rig depending on your
region, please ensure that you are using the correct instruction set. The
part number below should match the part number labeled on your box
IMPORTANT: Due to the nature of cut aluminium prole, some metal
shavings may still be present after our extensive QA cleaning process. We
recommend that boxes and packaging is opened on a hard oor.
NOTE: Some screws and washers are pre-installed. These will be part of
the parts list and will need to be loosened and reattached according to
the instructions.

4
If you have any issues, please contact us at [e-mail]
Part # Description QTY Check
BM-TA Bracket (Monitor), Triple Adjustable 4
EC-80 End Cap, 40x80 4
NF-M8 Nut (Flange), M8 16
NS-M8 T-Nut (Spring), M8 22
AL-80-580 Aluminum Aluminum Prole, 40x80x580mm 2
SH-M8-20 Screw (Hex), M8x20 22
SF-M8-16 Screw (Flat), M8x16 16
VM-02 VESA new 2
WF-M8 Washer (Flat), M8 22
WL-M8 Washer (Lock), M8 22
*NOTE: Extra hardware may be included as spare parts
IMPORTANT: As there are different versions of each rig depending on your
region, please ensure that you are using the correct instruction set. The
part number below should match the part number labeled on your box
TR80-TMARM4-BLK PARTS LIST

5
1
NOTE
FRONTSIDE
INSIDE
TOP SIDE
BACK SIDE
OUTSIDE
a
a
a
x
x
x
INSTALLATAION ORDER FOR SCREWS & WASHERS HOW TO MEASURE SCREWS
①SCREW ②LOCK WASHER
(IF APPLICABLE)
③WASHER
FLAT SCREW
HEX SCREW
BUTTON SCREW

6
NOTE
The handle screws (SL-M8-20 & SL-M8-25) are
ratcheted to allow for tightening and loosening
when space for rotation is limited. Simply pull the
handle out and turn handle into position and
push handle back in to engage thread.

7
NOTE
tooltip
tooltip
tooltip
tooltip
If T-Nuts are skipped, and
the ends are no longer
accessible, they can be
inserted by “rocking” them
in from the outer face as
shown.
Use the provided allen key
to push the T-Nut into
position and place the hole
to slide into position.
It is strongly advised that
spring T-Nuts are inserted by
sliding from the ends of
profiles. Please take careful
note of each step of all T-nuts
as some are to be installed in
anticipation of future steps.
NS-M8 & NS-M6

8
NOTE BC-40

tooltip
BM-TA x8 SH-M8-20 x8
M8x20mm
WL-M8 x8 WF-M8 x8
NS-M8 x8
SH-M8-20 x8
M8x20mm
WL-M8 x8 WF-M8 x8
NS-M8 x8
AL-80-580 x2 EC-80 x2
tooltip
NOTE: End caps may need to be removed to insert t-nuts.
9
1
2

tooltip
M8x16mm
SF-M8-16 x16 NF-M8 x16 VM-02-A x4 VM-02-B x4
VM-02 x2 NS-M8 x6 SH-M8-20 x6
M8x20mm
WL-M8 x6 WF-M8 x6
10
tooltip
NOTE: Optional for larger monitors.
3
4
If monitor mounting points are
150mm or 200mm apart, add
VESA extensions (VM-02-E)

tooltip
11
tooltip
IMPORTANT: If your monitor screws are under 8mm
(M8), you will need to use washers (not supplied)
5
6
EC-80 x4

12
Share your build online and tag us to be featured!
@trakracer @trakracer @trak_racer
FINISHED