Trampoline pro Jump Slammer User manual

www.trampolinepro.com

Warranty
1. Beginning from the date of purchase, the owner of the product has a 90 day warranty.
2. is warranty applies only to manufacturing defects of the product’s materials or construction.
3. is warranty does not apply to: Rim, Netting.
4. is warranty becomes void if: e product is used incorrectly or if the product is used in a way
that is outside the scope of intended use by its design. e product is not assembled and/or maintained
according to the instruction booklet. Aermarket parts are installed of if the product is altered/ modied
from its original design. Defects are a result of climatic inuences such as corrosion, UV rays, exposure
to hot, cold temperatures, humidity or otherwise normal disintergration. e product is rented out or
was made available to various unspecied persons in any other manner.
5. is warranty covers damage or failure that occurs during the course of NORMAL or INTENDED
USE of the product. Normal or intended use shall be described as activity that is necessary for the
participation in the sport for which the equipment is designed. NOT COVERED is damage caused by
deliberate hanging, multiple player hanging, vandalism, non-basketball activities or any other activity
that could be regarded as abusive.
6. To make a warranty claim contact Customer Service at [phone] or customerservice@trampoline-
pro.com for further instruction on how to return the product to Trampoline Pro under the warranty
program.
7. If Trampoline Pro ascertains that material and/or construction defects of the product or its components
have occurred during the warranty period, Trampoline Pro will repair or replace, according to its
choice, the product free of charge.
8. If the claim for warranty is not justiable, all expenses are the responsibility of the owner, including,
but not limited to, round-trip shipping costs.
9. is warranty is non-assignable and non-transferable.
Manufacturer’s Warranty
Outdoor Product Technologies, Inc (www.trampolinepro.com)
1

4. Horizontal plate 2 PCS
Components / Komponenten / Onderdelen / Composants
3. Clip Rod ( 6) 1PC
2. Flex Rod Thin ( 6) 1 PC
1. Flex Rod With Connector ( 6) 2PCS
5. Baskeball Rim with Net 1PC 6. Rim Pin 1PC
7. Adjust Bracket 1PC 8. Fixed Support 1PC
9. Backboard with net 1PC 2

10. Securing Bracket 4PCS 11. M8x110mm Bolt 4PCS
13. 8 Adjust Bracket Pin 1PC
14. Basketball 1PC
12. Twist Knob 4PCS
3

Assembly steps / Montageschritte / Montage / Assemblée
1A
4
5
6
1. Insert the two Horizontal plates (4) into the Basketball bracket with
net (5) as shown. Securing with the Rim Pin (6) as shown in 1A.
2. Insert Flex Rod Thin (2) into the Clip Rod (3) as shown in Pic 2A.Then connect the
Flex Rod with connector (1) onto the left and right of Flex Rod Thin (2) as shown
in pic 2B.
1
2
3
1
2A
2B
4

3. Bend the flex rod and insert the rod ends into the Horizontal plates (4) as
shown.
4. Insert the Clip Rod (3) end into the tube as shown.
5

6. Insert the Fixed Support (8) pole into the Adjust Bracket (7).
7
8
5. Slide the Backboard with net (9) onto the Flex Rod frame.
9
6

7. Attach the Fixed Support (8) pole to the enclosure pole using the four Securing
Brackets (10). M8x110mm Bolts (11) and Twist Knobs (12) as shown in picture.
Take caution to avoid injury while installing the Jump Slammer.
Use a ladder for safe installation.
If needed cut enclosure pole foam
to prevent Basketball hoop from
sliding. So the Securing Bracket is
touching metal.
11
12
10
7

13
8. Place the Basketball Rim with net (5) onto the Adjustment Bracket (7) and secure
with the adjustment bracket pin (13).
Note: Place the adjustment bracket pin (13) into one of the three adjustment
positions to adjust the location of the backboard. So, that it is lined up
vertically with your enclosure net.
8
9. The Backboard angle can be adjusted using the adjustment bracket’s
adjustment knob.Tighten or loosen the adjustment knob until the backboard is
vertical to the ground after installation.

10. Attach the Backboard with Net (9) by connecting it to the neighboring
enclosure sysem poles as shown in picture 10B. (Not all enclosure styles are
represented but the Jump Slammer should work with most enclosure styles).
Attach the backboard with net base (9) by using the small ties to secure the
Jump Slammer net to the top of the enclosure net as shown in pictures 10C,
10A.
9
Trampoline enclosure net
10B 10C
10A
Ties
Ties

11. Congratulations! You have finished the Jump Slammer assembly. Do not hang,
over jump or lose control while playing with the Jump Slammer. To avoid
unnecessary damage or injury, Jump Slammer is for single recreational play only.
10

Trampoline Pro
709 N 400 W STE 1
North Salt Lake, UT 84054
www.trampolinepro.com