Trampoline pro JUMP SLIDER User manual

TRAMPOLINEPRO"
dMP SLIDER
Trampoline Ramp Slide
USERS MANUAL
If you have questions after reading this manual,
or need to order replacement parts, please call
our Customer Care Hotline at [phone].
ACAUTION
Read all precautions and
instructions in this manual
Trampoline Ramp Slide
before using this equipment.
Keep this manual for
| future reference.
Replaces Tradtional Ladders

WARNING
Read the assembiy, installation, care, maintenance, and user instructions in this manual prior to
assembling and using this equipment. Save this manual for future reference.
BEFORE YOU BEGIN
Thank you for selecting the Jump Slider. This accessory, when combined with a propery
placed and maintained trampoline and enclosure, will provide many years of safe backyard fun. It allows you
to stow it away underneath the jump surface while still attached to free up more space.
This information must be read by all supervisors and users before any person is allowed to use the Jump Slider.
If you have any questions after reading this manual, please call our tol-free Customer Care Hotline at
1-800-473-5867. To help us better assist you, please mention the number of the product when calling.
www.trampolinepro.com
CARE AND MAINTENANCE
f your jump Slider becomes dirty, spray with water to clean. Do not allow use until completely dry.
Check all hardware before each use. Tighten any bolts and nuts that have become loose and if you notice any
broken parts, put your jump Slider away until it can be fixed.
The Jump Slider has a user weight limit of 200 Ibs and will accommodate any trampoline frame up to 3".
Exploded Parts Drawing
Key No. Qty.
Description
1
Lower Tube
Bent Tube
Upper Tube
Wing Nut
3
4
5
Cross Tube
Mat
7 2
Open C Bracket
8 M10 X
55mm Bolt
4-
Front
2

200071.2-ASSEMBLY
(1.
Step 1.
Attach
Base
Tube
Unfold
the
Jump
Slider
and
lay
on
a flat,
level
surface
or
ground
with
the
slightly
bent
tube
facing
upward
in
the
air.
Attach
the
Lower
Tube
(1)
into
the
Bent
Tube
(2)
as
shown.
Make
sure
the
curved
bottom
tube arc is facing outward. Line up
insert buttons with holes.
Step 2. Place Cross Tube
2.
strape 6
Slide the Cross Tube (5) through the two
loops sewn on the Mat (6) surface.
loop
loop
Step 3. Clamp Location
(3.
goor
Lift spring pad to access the frame.
Place
the
Open
C Brackets
(7)
approximately
20" apart same width as the preassembled
Jump Slider in front of the enclosure net
opening.
3

200071.2-ASSEMBLY
step
4.
Secure
Jump
Slider
Tighten
one
pole's
Wing
Nut
(4)
to
the
M10X55
mm Bolt (8), securing it to the trampoline frame.
Repeat
on
the
opposite
side.
8
Step
5.
Cover
hinges
and
tie
straps
to
rings
mat
V-ring
Find tie down straps sewn into the top edge
of the Jump Slider mat (6).
Tie the straps to the V-rings of your
trampoline mat.
Cover
the
hinges
with
Velcro
Fastener.
Velcro fastener
6.
Step 6. Storage Space
To help prevent unwanted access to the junmping
surface and securely stoW-away, open the hinge
velcro covers, then fold the Bent Tube (2)
underneath the Upper Tube (3) as shown.
Use the Velcro Fasteners straps underneath
to secure and hold in place.
Strap

200071.2-ASSEMBLY
Step 7. JumpSlider! 1
Lower your trampoline spring pad so that
It lays over the top of the Mat Surface.
Adjust
your
spring pad
as
necessary
to
ensure
the top of the Slide Surface is fully covered by
the spring pad. Prior to first use, adult or
supervisor should apply pressure in the center
of slide
to
test
stability.
90
DAY FULL
WARRANTY
Beginning from the date of purchase, the owner of the
product has a 90 day warranty.
This warranty applies only to manufacturers defects of
the products materials or construction.
This warranty becomes void if: The product is used
incorrectly or if the product is used in a way that is out
of the scope of use by its design. The product is not
assembled and/or not maintained according to the
instruction booklet. Aftermarket parts are installed or
if
the
product
is altered/ modified
from its
original design.
This warranty covers damage or failure that occurs during
the course of NORMAL and INTENDED USE of the product.
NOT COVERED is damage due to weather or Acts of God,
improper
or any other activity that could be regarded as abusive.
orage, negligence, user hanging, vandalism,
This warranty is
non-assignable
and
non-transferable.
Contact
Customer
Service
at
(800)
473-5867 for further
instruction
on
how
to
return
the
product
to
Trampoline
Pro
under
the
warranty
program.