TRENDnet TU2-ETG User manual

TU2-ETG
H/W: V1.3R
Quick Installation Guide

Table of Contents
Table of Contents
Version 08.21.2008
English .....................................................................................................
Troubleshooting ........................................................................................
1
1
2
4
1. Before You Start
2. ....................................................................................
................................................................................
How to Install

System Requirements
Application
Package Contents
1. Before You Start
English
1
?
?Driver CD-ROM
?Multi-Language Quick Installation
Guide
TU2-ETG
?
?
?CPU: 300MHz or above / 800MHz or above (Windows Vista)
?Memory: 256 MB RAM or above / 512 MB RAM or above
(Windows Vista)
?Windows 2000/XP/Vista
CD-ROM Drive
USB Port: 2.0 or 1.1
Gigabit
10/100 Fast Ethernet Speed
USB to Gigabit
Ethernet Adapter
(TU2-ETG)
4-Port Gigabit Firewall Router
(TWG-BRF114)
Notebook with
Gigabit PC Card
(TEG-PCBUSR)
Workstation with 10/100Mbps
PCI Adapter with WOL
(TE100-PCIWA)
Internet
Cable/DSL
Modem

2. How to Install
English
2
1. Insert the Driver CD-ROM into
your computer's CD-ROM Drive.
3. Click Install Driver, and then click
your operating system.
Note: Do not connect the TU2-ETG into your computer until instructed to do so.
2. Click Run Autorun.exe (Windows
Vista only).
4. Click Next. Then follow the
InstallShield Wizard instructions.

English
3
6. Connect the Adapter to an
available USB port on your
computer.
7. Drivers will install automatically.
5. Click Finish.
8. Connect a Cat-5e or Cat-6 RJ-45
cable from the Adapter to a Switch,
Router or Cable/DSL Modem.
Your installation is now complete.
For detailed information regarding the TU2-ETG configuration and advanced
settings, please refer to User Guide on the Driver and User Guide CD-ROM.
Register Your Product
To ensure the highest level of customer service and support, please take a moment to
register your product Online at: www.trendnet.com/register
Thank you for choosing TRENDnet

4
Q1:
A1:
Q2:
A2:
Q3:
A3:
Q4:
Can I connect or disconnect the TU2-ETG while the computer is on?
Yes, you can connect or disconnect the TU2-ETG while the computer is on
because the USB interface is Plug-and-Play compliant and hot-pluggable.
Windows is unable to recognize my hardware. What should I do?
First, make sure your computer meets the minimum requirements as specified
in Section 1 of this Quick Installation Guide. Second, try plugging the adapter into
a different USB port.
Windows recognizes my new hardware, but I'm unable to connect to my
network. What should I do?
First, verify that the network cable is securely connected from your switch or
router to your adapter. Second, verify that the LEDs on your adapter are lit. Third,
verify that the TCP/IP settings are set to Obtain an IP address automatically.
When I connect the adapter to a gigabit switch, I am not getting gigabit
speeds. What should I do?
Make sure you are using CAT-5e or CAT-6 Ethernet Cables. Some CAT-5
cables are not rated to run in Gigabit.
If you still encounter problems or have any questions regarding the TU2-ETG, please
refer to the User's Guide included on the Driver CD-ROM or contact TRENDnet's
Technical Support Department.
A4:
Troubleshooting

Certifications
This equipment has been tested and found to comply with FCC and CE Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received. Including interference that may
cause undesired operation.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.
Waste electrical and electronic products must not
be disposed of with household waste. Please
recycle where facilities exist. Check with you Local
Authority or Retailer for recycling advice.
ADVERTENCIA
En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de alimentacón
necesario para su funcionamiento. El uso de un adaptador distinto al mencionado puede producir
daños fisicos y/o daños al equipo conectado. El adaptador de alimentación debe operar con voltaje y
frecuencia de la energia electrica domiciliaria existente en el pais o zona de instalación.

Copyright ©2008. All Rights Reserved. TRENDnet.
Product Warranty Registration
Please take a moment to register your product online.
Go to TRENDnet’s website at http://www.trendnet.com/register
20675 Manhattan Place
Torrance, CA 90501
USA