TRENDnet TU2-ET100 User manual

Copyright ©2005. All Rights Reserved. TRENDware International, Inc.
TRENDnet
TRENDware, USA
What's Next in Networking
TU2-ET100
Version 01.26.05
USB 2.0 Fast Ethernet Adapter
Quick Installation Guide
GAdaptateur Fast Ethernet USB 2.0
Guide d'installation rapide
USB 2.0 Fast-Ethernet-Adapter
Kurzanleitung zur Installation
Guía de instalación rápida del
adaptador Fast Ethernet con USB 2.0

Table of Contents
English ......................................................................................................
Troubleshooting ........................................................................................
1
1
2
3
4
14
1. Prepare for Installation ......................................................................
2. Product Detail ....................................................................................
3. Hardware Installation .........................................................................
4. Driver Installation ...............................................................................

Thank you for purchasing TRENDnet's TU2-ET100 USB 2.0 Fast Ethernet
Adapter.
This guide will help you set-up your USB 2.0 Fast Ethernet Adapter. Following
the installations should be quick and easy. If you run into problems, please
refer to the Troubleshooting section. If you need further technical support,
please visit www.TRENDNET.com or call technical support by phone.
Verify Package Contents
Please make sure you have everything in the box:
1
1. Prepare for Installation
English QIG
English
Minimum System Requirements
1. Pentium 300Mhz or faster with at least 64MB RAM
2. Computer with an available USB slot
3. Windows XP, 2000, ME, 98SE
TU2-ET100 CD-ROM Quick Installation Guide
Copyright ©2005. All Rights Reserved. TRENDware International, Inc.
TRENDnet
TRENDware, USA
What's Next in Networking
TU2-ET100
Version 01.26.05
USB 2.0 Fast Ethernet Adapter
Quick Installation Guide
GAdaptateur Fast Ethernet USB 2.0
Guide d'installation rapide
USB 2.0 Fast-Ethernet-Adapter
Kurzanleitung zur Installation
Guía de instalación rápida del
adaptador Fast Ethernet con USB 2.0

2
2. Product Detail
The USB 2.0 Fast Ethernet Adapter has one RJ-45 connector, an LED for
network activity and an attached USB cable.
English
LED for network activity
RJ-45 connector
Attached USB cable

3
3. Hardware Installation
1. Turn on your computer and allow your operating system to fully load into the
system.
2. Connect the Type-A connector of your TU2-ET100 into a USB slot of your
desktop or notebook.
English
3. Connect one end of the CAT-5 cable into the TU2-ET100's RJ-45 port, and
connect the other end into your switch, router, cable modem, or DSL modem.

4
4. Driver Installation
English
Windows XP
After inserting the TU2-ET100 into one of your USB ports, the “Found New
Hardware” message appears. Please insert the TU2-ET100 Driver CD-ROM
into your computer's CD-ROM drive.
1. Click Install the software automatically (Recommended) and Click Next.
2. Select d:\winxp\ax88772.inf and Click Next.

5English
NOTE: TRENDnet's USB 2.0 Fast Ethernet Adapter has been fully
tested under all supported Windows Operating Systems and has been
approved for their functionality; click Continue Anyway.
3. Click Finish.
Your driver installation is now complete.

6English
After inserting the TU2-ET100 into one of your USB slots, the “Found New
Hardware” message appears.
1. Insert the TU2-ET100 Driver CD-ROM that came with this product. Click
Next.
2. Select Search for suitable driver for my device (recommended) and Click
Next.
Windows 2000

7English
3. Select Specify a location and Click Next.
4. Type D:\win2k in the text box and Click OK.
5. Click Next.
NOTE: Replace “D” in “D:\win2k” with whichever letter is assigned to
your CD-ROM drive.

8English
NOTE: TRENDnet's USB 2.0 Fast Ethernet Adapter has been fully
tested under all supported Windows Operating Systems and has been
approved for their functionality; click Yes.
6. Click Finish.
Your driver installation is now complete.

9English
After inserting the TU2-ET100 into one of your USB slots, the “Found New
Hardware” message appears.
1. Insert the TU2-ET100 Driver CD-ROM that came with this product. Click
Specify the location of the driver and Click Next.
2. Click Search for a better driver, click Specify a location: and type in
D:\WinMe. Click Next.
Windows Me

10 English
3. Click Next.
4. Click Next.
5. Click Finish.

11 English
6. Click Yes.
2. Click Search for the best driver for your device and click Next.
Your driver installation is now complete.
After inserting the TU2-ET100 into one of your USB slots, the “Found New
Hardware” message appears.
1. Click Next.
Windows 98SE

12 English
3. Click Specify a location: and type in D:\Win98. Click Next.
4. Click Next.
5. Insert the Windows 98SE CD-ROM into your computer's CD-ROM drive.
6. Click OK.

13 English
7. Click Finish.
8. Click Yes.
Your driver installation is now complete.

14
Q1.
A1.
Q2.
A2.
Q3.
A3.
Can I connect or disconnect TU2-ET100 while the computer is on?
Yes, you can connect or disconnect TU2-ET100 while the computer is on
because the USB interface is Plug-and-Play compliant and hot-pluggable.
After successful installation of the TU2-ET100 USB Fast Ethernet, I connected
my USB device into a USB slot, but it does not seem to work. What should I do?
Make sure that the CAT-5 cable is connected properly into your switch, or
broadband modem. Double check the connection at the other end of the CAT-5
cable, and verify that the cable is inserted properly into your TU2-ET100. Also,
verify that your switch or your broad-band modem is getting any power.
When I verify the installation of the TU2-ET100, I see an exclamation point on
my network adapter. What should I do?
Go to Control Panel and double-click the System icon. Go to the Device
Manager and expand the Network adapters heading. Double-click ASIX
ax887722 USB2.0 to Fast Ethernet Adapter (the icon that has an exclamation
point on it), and click the Driver tab. On the Driver tab, click Update Driver. Use
4. Driver Installation in this installation manual to guide you in installing your driver.
If you have any questions regarding the TU2-ET100, please contact Trendware
Technical Support Department.
Troubleshooting
This equipment has been tested and found to comply with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received including interference that may
cause undesired operation.
This equipment is in compliance with the requirements of the following regulations: EN
55 022: CLASS B

Copyright ©2005. All Rights Reserved. TRENDware International, Inc.
@
TRENDnet
TRENDware, USA
What's Next in Networking
Product Warranty Registration
Please take a moment to register your product online.
Go to TRENDware’s website at http://www.TRENDNET.com
TRENDware International, Inc.
3135 Kashiwa Street. Torrance, CA 90505
http://www.TRENDNET.com
TRENDnet Technical Support
Contact
Telephone:
Fax:
Email:
1(310) 626-6252
1(310) 626-6267
[email protected]
Tech Support Hours
7:30am - 6:00pm Pacific Standard Time
Monday - Friday
Tech Support Hours
Telephone
Fax:
Deutsch :+49 (0) 6331 / 268-460
Français :+49 (0) 6331 / 268-461
Español :+49 (0) 6331 / 268-462
English :+49 (0) 6331 / 268-463
Italiano :+49 (0) 6331 / 268-464
Dutch :+49 (0) 6331 / 268-465
+49 (0) 6331 / 268-466
8:00am - 6:00pm Middle European Time
Monday - Friday
US/Canada Support Center European Support Center
Contact