TRENDnet TS-S402 - Diskless SATA I/II Network Attached Storage... User manual

Quick Installation Guide
TS-S402

Table of Contents
Table of Contents
Version 11.28.2007
English .....................................................................................................
Troubleshooting ........................................................................................
1
1
2
4
7
12
1. Before You Start
2. .........................................................................
.................................................................................
Hardware Installation
Configure the Storage Server
4. Using the TS-S402 .............................................................................
3. ............................................................

System Requirements
Application
Package Contents
1. Before You Start
English
1
Note: Hard Drive and USB Storage Device are not included.
Cable/DSL
Modem
300Mbps Wireless N
Gigabit Router
(TEW-633GR)
Workstation with
Gigabit PCI Adapter
(TEG-PCITXR)
10/100Mbps Multi-Port
Print Server
(TE100-P21)
Internet
2-Bay SATA I/II Network
Storage Enclosure
(TS-S402)
Printers
10/100Mbps Gigabit
Notebook with
300Mbps Wireless N
PC Card
(TEW-621PC)
Wireless 300Mbps
?
?Utility CD-ROM
?
?Power Cord
?AC Power Adapter (12V DC, 7.0A)
?Mounting Brackets
Quick Installation Guide
TS-S402
?
?A computer with a network adapter properly installed
?A network Switch or Hub with an available network LAN port
?A RJ-45 network cable.
?SATA I/II Hard Drive or USB 2.0 Storage Device (i.e. flash drive, external
hard drive)
?iTunes (optional)
Web Browser: Internet Explorer (6.0 or higher)

2. Hardware Installation
English
2
4. Repeat steps 1-3 for a second hard
drive.
3. Insert the hard drive into one of the
two slots. Then connect the SATA
data and power cable to the hard
drive.
2. On the front of the TS-S402, press
push to open up the enclosure
door.
5. If you have a USB storage device,
connect it to one of the 2 USB
ports on the front or back of the
TS-S402.
1. Secure the supplied hard drive
brackets to both sides of a 3.5”
SATA hard drive using the provided
screws.

English
3
7. Connect the power cord to the
power adapter.
Your hardware installation is now complete.
6. Connect a RJ-45 cable from the
Switch/Hub to the LAN port of the
TS-S402.
8. Connect the External Power
Adapter to the Storage Server and
then to a power outlet.
9. Press the power button.
10. Verify that the following panel
lights are on: Power, LAN, HDD.
Register Your Product
To ensure the highest level of customer service and support, please take a moment to
register your product Online at: www.trendnet.com/register
Thank you for choosing TRENDnet

English
4
3. Configure the Storage Server
Note: It is recommended that you configure the Storage Server from a wired
computer. Since the Storage Server's default IP address is 192.168.10.10,
make sure no other network devices are assigned an IP address of
192.168.10.10.
For Windows Users
3. Double-click the NAS Utility icon.
2. Follow the Installation Wizard
instructions and then click Finish.
Repeat step 1 and 2 for each
Windows client PC.
4. Select the storage server and click
Attach.
1. Insert the Utility CD-ROM into
your computer's CD-ROM Drive
and then click Install Utility.

English
5
7. Select the Format Type (e.g.
EXT2, EXT3) and then click Next.
5. Click Yes.
6. Enter the administrator User ID
and Password. Then click Login.
By default:
User: admin
Password: admin
8. Click OK to continue.
9. Click Finish.

English
6
Your configuration is now complete.
For detailed information regarding the TS-S402 configuration and advanced
settings, please refer to the Troubleshooting section, User's Guide CD-ROM, or
TRENDnet's website at http://www.trendnet.com.
10. Click Device Setting.
11. Enter the administrator User
name and Password, and then
click OK. By default:
User Name: admin
Password: admin
12. Click Configuration, and then click
Networking. Configure the IP
Address, Subnet mask,
Gateway and then click Modify.
Note: The IP Address must match
the network segment of your
network.

English
7
4. Using the TS-S402
Add User
3. Click the green plus sign to add
additional users.
Note: A User Name can only be
used on one computer at a time.
Add a user name for each client
that will have access to the
TS-S402.
1. In the browser configuration, click
Share Management, then user
management. Then click on the
green plus sign. If you are creating
a shared folder, skip this step and
continue on to Create Folder.
2. Enter a User Name and Password,
confirm the password and then
click Apply.

English
8
Access Folder on Windows Client PC
Create Folder
1. Click Share Management, then
click Share Folder. Select the
Disk Name, and enter a Folder
Name.
Shared Folder
Select Anonymous, and then
click apply.
Private Folder
Click Private Folder. Select a
user, then click Add New User.
Click Read Only to give read only
access, then click Apply.
1. Open up the NAS utility (see step
2 and 3 under Section 3: Configure
the Storage Server)
2. Enter the client's User (user name)
and Password. Then click Login.
See Add User above if you have
not added a user.

English
9
3. Right click the folder and click
Mount.
4. If you are accessing a private
folder, this window will appear.
Click OK.
5. Select an available Drive (e.g. Z:)
and click Finish.
6. Double-click the folder (e.g. share
<Z:>. Z represents the available
Drive that you selected in step 2.)

English
10
Backup data on USB drives to share folder on
hard drive
3. Double click on the share folder.
4. USBCopy folder will appear.
2. Wait until SYS and HDD/HDD2
LEDs become steady.
1. Press the Backup button on the
front of the storage server until the
SYS and HDD /HDD2 LEDs are
blinking.
7. Repeat steps 1-7 on each
Windows PC.

English
11
Setting up iTunes Server
1. In the browser configuration for the
TS-S402, click on Configuration,
then click Server Preference. By
default, iTunes is enabled. If
iTunes is disabled, select Enable
and then click Apply.
2. Click Service Configuration and
then click iTunes Server. Enter a
iTunes Server Name, select a
Share Folder and enter a refresh
time (seconds). Click Enable to
enable password protection. Set
and confirm password, and then
click Apply.
3. On a client PC, open iTunes. Click
iTunes Servers. If you enabled
password, enter the password and
then click OK.
4. If you have any music in the
shared folder, the songs will now
appear.

12
Q1:
A1:
Q2:
A2:
Can I connect or disconnect the USB storage device while the TS-S402 is on?
Yes, you can connect or disconnect any external USB device while the computer is on,
because the USB interfaces are Plug-and-Play and hot-pluggable.
The NAS utility is unable to detect the Storage Server. What should I do?
First, check your hardware settings again by following the instructions in section 2.
Second, make sure the LAN lights is lit. Third, disable any software firewall programs
(e.g. Norton Internet Security, McAfee). If you are running Windows XP or Vista, disable
the built-in firewall. Fourth, try installing the NAS utility on another Windows PC. Fifth,
Take a pin or paperclip, press on it for 15 seconds and then let go. Sixth, put a static IP
address in the same subnet as the storage server. Then open up your browser and type
in the address bar http://192.168.10.10. Then hit Enter. Please see the steps below for
instructions on putting a static IP address on your Windows PC:
Troubleshooting
Q3:
A3:
I am unable to mount or access the SATA hard drive. What should I do?
First, verify that the SATA hard drive has been properly installed (see section 2).
Second, connect the SATA hard drive to the second SATA power and data cable. Third,
double click on My Computer. If you were able to mount the device, you should see the
icon for drive under Network Drives.
1. Go into the Control Panel and double-click
the Network Connections icon, right-click
the Local Area Connection icon and then
click Properties.
2. Click Internet Protocol (TCP/IP) and then
click Properties. Then click on Use the
following IP address, and make sure you
assign your network adapter an IP address
in the subnet of 192.168.10.x.

Q4:
A4:
What file formats are supported?
EXT2 and EXT3 file formats are supported for hard drive. FAT16, FAT32 and NTFS file
formats are support for USB storage devices.
: I setup a password on my storage server, but I forgot it. How do I reset the storage
server to factory defaults.
There is a reset button on the back of the storage server. Take a pin or paperclip, press
on it for 15 seconds and then let go. The default user name and password is admin.
I press on the power button on the TS-S402 to turn it off, but it remains on. What should
I do?
Make sure to press the power button all the way in and hold for five seconds.
When I connect the storage device to a Gigabit switch, I am not getting Gigabit speeds.
What should I do?
Make sure you are using CAT-5e or CAT-6 Ethernet Cables. Some CAT-5 cables are
not rated to run in Gigabit.
Q5
A5:
Q6:
A6:
Q7:
A7:
If you still encounter problems or have any questions regarding the TS-S402, please contact
TRENDnet's Technical Support Department.
13

Certifications
This equipment has been tested and found to comply with FCC and CE Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received. Including interference that may
cause undesired operation.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.
Waste electrical and electronic products must not
be disposed of with household waste. Please
recycle where facilities exist. Check with you Local
Authority or Retailer for recycling advice.
ADVERTENCIA
En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de
alimentacón necesario para su funcionamiento. El uso de un adaptador distinto al
mencionado puede producir daños fisicos y/o daños al equipo conectado. El adaptador
de alimentación debe operar con voltaje y frecuencia de la energia electrica domiciliaria
existente en el pais o zona de instalación.

Product Warranty Registration
Please take a moment to register your product online.
Go to TRENDnet’s website at http://www.trendnet.com/register
TRENDnet Technical Support
US Canada
24/7 Tech Support
Toll Free Telephone: [phone]
Europe (Germany France Italy Spain Switzerland UK)
English/Espanol - 24/7
Francais/Deutsch - 11am-8pm, Monday - Friday MET
English/Espanol - 24/7
Francais/Deutsch - 11am-8pm, Monday - Friday MET
Worldwide
Telephone: +(31) (0) 20 504 05 35
Toll Free Telephone: [phone]
.
. . . . .
Copyright ©2007. All Rights Reserved. TRENDnet.
20675 Manhattan Place
Torrance, CA 90501
USA