TRIGA TRW-B210W User manual
TRW-B210W Wireless Detector Base
INSTALLATION AND MAINTENANCE INSTRUCTIONS
BEFORE INSTALLING
Please read the System Smoke Detectors Application Guide, which provides de-
tailed information on detector spacing, placement, zoning, wiring, and special
applications. Copies of this application guide are available from System Sen-
sor. In addition, the wireless system must be installed in compliance with the
control panel system installation manual and the SWIFT® Wireless Gateway
Manual. The installation must meet the requirements of the Authority Hav-
ing Jurisdiction (AHJ). Sensors offer maximum performance when installed in
compliance with the National Fire Protection Association (NFPA); see NFPA 72.
NOTICE: This manual should be left with the owner/user of this equipment.
IMPORTANT: The detector used with this base must be tested and maintained
regularly following NFPA 72 requirements. The detector should be cleaned at
least once a year.
GENERAL DESCRIPTION
The TRW-B210W is a mounting base designed for addressable wireless detec-
tors. The base includes a magnet for tamper resistance (Figure 1). The magnet
SPECIFICATIONS
Base Diameter: 6 inches (15 cm)
Base Height: 1.2 inches (30 mm)
Operating Temperature Range: Refer to the applicable sensor’s operating temperature range provided in the sensor’s installation manual.
SNAP ON
DECORATIVE
RING
DETECTOR
BASE
FIGURE 2. BASE AND TRIM RING
C02008-00
MAGNE
T
C02007-00
FIGURE 1. BASE WITH MAGNET
activates a supervisory tamper fault at the panel if the detector is removed from
the base.
MOUNTING AND INSTALLATION GUIDELINES
The TRW-B210W wireless detector base can be mounted directly to a perma-
nent structure in its desired location. Since there are no wires running to the
base, an electrical box is not required. However, hole configurations are avail-
able that could be mounted to a 4 inch square (with or without plaster rings),
4-inch octagon, 3.5-inch octagon or single gang junction boxes.
NOTE: When mounting wireless devices on or around metal objects, signal
strength may be directionally affected.
For installation, remove the decorative ring by turning it in either direction to
unhook the snaps, then separate the ring from the base.
Place the decorative ring on the base and rotate it in either direction until it
snaps into place (see Figure 2).
I56-4064TRG-002
TRIGA Life Safety Systems, LLC
7600 Olde Eight Rd.
Hudson, Ohio 4426-1057
1 I56-4064TRG-002
2/1/2021
Use of these products in combination with non-Honeywell prod-
ucts in a wireless mesh network, or to access, monitor or control
devices in a wireless mesh nework via the internet or another
external wide area network, may require a separate license from
Sipco, LLC. For more information, contact Sipco, LLC or Ipco, LLC
at 8215 Roswell Rd., Building 900, Suite 950, Atlanta, GA 303350,
or at www.sipcollc.com or www.intusiq.com.
LICENSING STATEMENT
The base includes an area for recording the zone, address, and type of detec-
tor being installed. This information is useful for setting the detector head
address and for verification of the detector type required for that location.
TAMPER-RESIST FEATURE
NOTE: Do not use the tamper-resist feature if the removal tool will be used.
The detector base includes a tamper-resist feature that prevents removal of the
detector without using a small screwdriver or similar tool.
To activate this feature, use needle-nose pliers to break the tab on the detector
base as shown in Figure 3A. Then, install the detector.
To remove the detector from the base once the tamper-resist feature has been
activated, remove the decorative ring by rotating it in either direction and
pulling it away from the base. Then, insert a small screwdriver into the notch,
as indicated in Figure 3B, and press the plastic lever toward the mounting
surface before rotating the detector counterclockwise for removal.
The tamper-resist feature can be defeated by breaking and removing the plastic
lever from the base. However, this prevents the feature from being used again.
FIGURE 3A. ENABLING THE TAMPER-RESISTANT CAPABILITY
PLASTIC LEVER
BREAK TAB AT DOTTED LINE BY
TWISTING TOWARD CENTER OF BASE
USE SMALL-BLADED SCREWDRIVER TO PUSH
PLASTIC LEVER IN DIRECTION OF ARROW
C0130-00
FIGURE 3B. REMOVING THE DETECTOR HEAD FROM THE BASE
USE SMALL-BLADED SCREWDRIVER TO PUSH
PLASTIC LEVER IN DIRECTION OF ARROW
C02009-00
Triga™ is a trademark of TRIGA Life Safety Systems, LLC. SWIFT® and System Sensor® are registered trademarks of Honeywell International, Inc.
2 I56-4064TRG-002
©2021. 2/1/2021
