TRINITY Pro TIJZ-0949 User manual

OWNER’S MANUAL
TRINITY PRO 4-TIER NSF 72" x 30" x 72"
WIRE SHELVING RACK
Model # TIJZ-0949 / TIJPBA-0949

Your TRINITY Pro 4-Tier NSF 72"x30"x72“ Wire Shelving Rack should include the following parts. Please
inspect box contents to ensure you have received all components.
If you are missing any parts, need assistance with assembly or have questions, please contact TRINITY
Customer Service: 800.985.5506 or [e-mail]. Parts can also be requested online at
www.trinityii.com (Help & More, Contact Us).
You will need no additional tools for assembly.
PARTS LIST
SLIP SLEEVE
(32) + (2) extra
SHELF (4)BOTTOM POLE (4)
© 2019 TRINITY - 800.985.5506
1
AB C
DE
FEET LEVELER (4)
Note: The black circular plastic spacers in between Shelves are used only for packaging
purposes. They are NOT NEEDED. Please discard.
TOP POLE (4)
End Cap (4) and
pole connector (4)
pre-installed

© 2019 TRINITY - 800.985.5506
ASSEMBLY INSTRUCTIONS
Note: There will be a very small gap in-between two locked SLIP SLEEVES (D)—this is normal.
2
A (4) E (4)
Note that POLES (A+B) have slight horizontal line
indentations at 1” intervals. SLIP SLEEVES (D) have
raised horizontal lines inside designed to lock them in
place on POLES (A+B).
On BOTTOM POLE (A), place one pair of SLIP SLEEVES
(D) at desired height no higher than 3rd indentation
from the bottom. Please make sure arrow faces up
and word “TOP” is right side up.
Slide pair of SLIP SLEEVES (D) until you hear a click to
confirm the pair is locked onto BOTTOM POLE (A). DO
NOT place more than one pair on each POLE (A) at a
time. Do this for each BOTTOM POLE (A) and make
sure height is identical for each BOTTOM POLE (A).
For easiest assembly, do not attach TOP POLES
(B) and BOTTOM POLES (A) until instructed. Once
connected, these will be posts for the rack.
Screw each FEET LEVELER (E) into bottom of each
BOTTOM POLE (A). Turn clock-wise to screw in
place.
STEP 1
STEP 2
A (4) D (8)
E
A
A
D

ASSEMBLY INSTRUCTIONS
C (1)
Place SHELF (C) on its side and slide each BOTTOM
POLE (A) through each corner cylinder on SHELF (C).
Make sure SHELF (C) corner cylinders are positioned
over SLIP SLEEVES (D).
Stand the unit upright.
Note:
•Level side of SHELF (C) is TOP side (TRINITY logo on
corner cylinders should be right-side up.)
•Use a rubber mallet, if needed, to secure SHELF (C).
STEP 3
STEP 4
C (1) D (8)
On BOTTOM POLE (A), place 1 pair of SLIP
SLEEVES (D) at desired height between
SHELVES (C). Make sure arrow faces up
and word “TOP” is right side up. Do this
for each BOTTOM POLE (A), and make
sure height is identical for each BOTTOM
POLE (A).
Lower SHELF (C) over each BOTTOM POLE
(A) so corner cylinders of SHELF (C) are
positioned over SLIP SLEEVES (D).
Note: Use a rubber mallet, if needed, to
secure SHELF (C).
A
C
A
AD
© 2019 TRINITY - 800.985.5506
3

ASSEMBLY INSTRUCTIONS
B (4)
STEP 5
STEP 6
Screw TOP POLE (B) into BOTTOM POLE
(A).
Repeat for each remaining TOP POLE (B).
Note: The top of each TOP POLE (B) is
indicated by a BLACK END CAP.
Repeat Step 4 to install other
SHELVES (C) as desired.
Note:
•Use a rubber mallet, if needed,
to secure SHELVES (C).
•After assembly, adjust FEET
LEVELERS (E) as needed to
ensure shelving rack is level.
C (2) D (16)
© 2019 TRINITY - 800.985.5506 4
C
D
C
A
B