Tripp Lite DWFSC3255MUL User manual

1
Owner’s Manual
Este manual esta disponible en español en la página de Tripp Lite: www.tripplite.com
Ce manuel est disponible en français sur le site Web de Tripp Lite : www.tripplite.com
Dieses Handbuch ist in deutscher Sprache auf der Tripp Lite-Website verfügbar: www.tripplite.com
Ɋɭɫɫɤɨɹɡɵɱɧɚɹɜɟɪɫɢɹɧɚɫɬɨɹɳɟɝɨɪɭɤɨɜɨɞɫɬɜɚɩɪɟɞɫɬɚɜɥɟɧɚɧɚɜɟɛɫɚɣɬɟɤɨɦɩɚɧɢɢ7ULSS/LWHɩɨɚɞɪɟɫɭZZZWULSSOLWHFRP
Fixed Wall Mount
for Flat and Curved Screens –
Security Version
Model: DWFSC3255MUL
PROTECT YOUR INVESTMENT!
Register your product for quicker service and ultimate peace of mind.
You could also win an ISOBAR6ULTRA surge protector—a $100 value!
www.tripplite.com/warranty
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2017 Tripp Lite. All rights reserved.
200x200 / 300x300 /
400x200 / 400x400 55”
MAX 99 lb.
(45 kg)
MAX

2
Important Safety Instructions
Warranty & Product Registration
NOTE: Read the entire instruction manual before you start installation and assembly.
WARNING
• Do not begin the installation until you have read and understood the instructions and warnings contained in this manual. If you have
any questions regarding any of the instructions or warnings, please visit www.tripplite.com/support.
• This mounting bracket was designed to be installed and utilized ONLY as specified in this manual. Improper installation of this
product may cause damage or serious injury.
• This product should only be installed by someone of good mechanical ability, with basic building experience and a full understanding
of this instruction manual.
• Make sure that the mounting surface can safely support the combined load of the equipment and all attached hardware and
components.
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. The use of a stud finder
is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not over-tighten. Over-tightening can damage the items, greatly reducing their holding power.
• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
5-Year Limited Warranty
Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in material and workmanship for a period of 5 years from the date
of initial purchase. If the product should prove defective in material or workmanship within that period, Seller will repair or replace the product, in its sole discretion.
THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE, ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES
OTHER THAN THE WARRANTY EXPRESSLY SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING ALL WARRANTIES
OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND
CONSEQUENTIAL DAMAGES. (Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from
jurisdiction to jurisdiction).
WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate or safe for the use intended. Since individual applications are
subject to great variation, the manufacturer makes no representation or warranty as to the suitability or fitness of these devices for any specific application.
PRODUCT REGISTRATION
Visit www.tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product!*
* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice.

3
IMPORTANT: Ensure all parts according to the component checklist have been received prior to installation. If any parts are
missing or faulty, visit www.tripplite.com/support for service.
Component Checklist
Wall Plate (x1)
M5 x 14 (x4) M6 x 14 (x4) M6 x 30 (x4) M8 x 30 (x4) M8 x 50 (x4) Washer (x4) Small
Spacer (x8)
Big
Spacer (x8)
Anchor Bolt (x4) Concrete Anchor
(x4)
20 mm Washer
(x4)
Adapter Bracket (x2) Security Bar (x1)
Hex Key (x1) Right End Cap (x1)Left End Cap (x1) Combo Lock (x1)End Cap Screws (x4)
Installation
1Assemble the Wall Plate
End Cap
Screws

4
Installation
2A Mount on Wood Stud Wall
WARNING
• Make sure that mounting screws are anchored into the center of the studs. Use of a stud finder is highly recommended.
• Installers are responsible to provide hardware for other types of mounting situations.
• Installers must verify that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
20 mm
Washer Anchor
Bolt
55 mm
(2.2 in.)
O4.5 mm
O(3/16 in.)
Find and mark the exact
location of mounting holes
Screw the
assembled wall
plate onto the
wall
Drill pilot holes

5
Installation
2B Mount on Solid Brick
or Concrete Block
WARNING
• When installing wall mounts onto a concrete masonry unit (also known as a CMU or “cinder block”), verify that the actual
concrete thickness is at least 35 mm (1-3/8”) in order to hold the concrete anchors. DO NOT DRILL INTO MORTAR JOINTS!
Be sure to mount the assembled wall-mount plate with the included concrete anchors, D6 washers and anchor bolts onto
solid sections of the blocks. The solid sections can generally be found 25 mm (1”) toward the middle of the block from
either end. An electric drill on a slow setting is suggested to drill the hole rather than a hammer drill so as to avoid
breaking out the back of the hole when entering a hollow section.
• Installers must verify that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
60 mm
(2.4 in.)
O10 mm
O(3/8 in.)
Find and mark
the exact
location of
mounting holes
Drill pilot holes
Screw the
assembled wall
plate onto the
wall
20 mm
Washer
Anchor
Bolt
Concrete
Anchor

6
Installation
3Install Adapter Brackets
3-1 For Flat Back Screen
3Install Adapter Brackets
3-2 For Curved Screen or Recessed Back Screen
M5 x 14
M6 x 14
Washer
Note: Choose appropriate screws, washers and spacers (if necessary) according to the type of screen.
• Position the adapter brackets as close as possible to the center of the display.
• Screw the adapter brackets onto the display.
Firmly secure all screws. Do not over-tighten.

7
Installation
4Hang Display onto the Wall Plate
• Using an assistant or mechanical
lifting equipment, hook the display
with attached adapter brackets over
the top of the mounted wall plate.
• Push the safety clamps on the
bottom of the adapter brackets
upward and tighten the two screws
to lock each bracket to the wall
plate.
M6 x 30
M8 x 30
M6 x 30
M8 x 30
M6 x 30
M8 x 30
M8 x 50 M8 x 50 M8 x 50
Washer Washer Washer
Washer
Wall Wall
Washer Washer
Small
Spacer
Small
Spacer
Small
Spacer
Big
Spacer
Big
Spacer
Big
Spacer
Big
Spacer
Big
Spacer
Small
Spacer

8
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
17-12-093 93-37DC_RevB
LP22-44F
Maintenance
• Check that the bracket is secure and safe to use at regular intervals (at least every three months).
• Please visit www.tripplite.com/support if you have any questions.
Installation
5Slide Security Bar through the Mounting Brackets and
Attach Combo Lock to Secure
5Use the Included Hex Key to Secure the Mounting Brackets to the Wall Plate
Combo
Lock
Security Bar
Hex Key