Tripp Lite SRWF12U38 User manual

1
Owner’s Manual
Low-Profile Wall-Mount
SmartRack®Enclosures
Models: SRWF12U38, SRWF16U38
PROTECT YOUR INVESTMENT!
Register your product for quicker service and ultimate peace of mind.
You could also win an ISOBAR6ULTRA surge protector—a $100 value!
www.tripplite.com/warranty
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2016 Tripp Lite. All rights reserved.
Table of Contents
1. Important Safety Instructions 2
2. Overview 2
3. Feature Identification 2
4. Preparation 3
4.1. Unpacking 3
4.2. Disassembly 3
5. Installation 4
5.1. Mounting the Backplate 4
5.2. Unit and Equipment Installation 5
6. Enclosure Configuration 7
6.1. Cable Access and Management 7
6.2. Ground Connection 7
7. Specifications 7
8. Storage and Service 7
9. Warranty and Product Registration 8
Español 9
Français 17
Русский
25
16-04-227-9335C5.indb 1 9/2/2016 10:18:55 AM

2
1. Important Safety Instructions
3 Feature Identification
2. Overview
SAVE THESE INSTRUCTIONS
This Manual contains instructions and warnings that must be followed during the installation and operation of the product
described in this manual. Failure to comply may invalidate the warranty and cause property damage or personal injury.
• Keep the enclosure in a controlled indoor environment, away from moisture, temperature extremes, flammable liquids and gasses,
conductive contaminants, dust and direct sunlight.
• Leave adequate space at the front and rear of the enclosure for proper ventilation. Do not block, cover or insert objects into the external
ventilation openings of the enclosure.
• The enclosure is extremely heavy. Use caution when handling the enclosure. Do not attempt to unpack, move or install it unassisted. Use a
mechanical device such as a forklift or pallet jack to move the enclosure in the shipping container.
• Do not place any object on the enclosure, especially containers of liquid, and do not attempt to stack the enclosures.
• Inspect the shipping container and the enclosure for shipping damage. Do not use the enclosure if it is damaged.
• Leave the enclosure in the shipping container until it has been moved as close to the final installation location as possible.
• Install the enclosure in a structurally sound area capable of handling the load, or on a level floor that is able to bear the weight of the
enclosure, all equipment that will be installed in the enclosure and any other enclosures and/or equipment that will be installed nearby.
• Use caution when cutting packing materials. The enclosure could be scratched, causing damage not covered by the warranty.
• Save all packing materials for later use. Repacking and shipping the enclosure without the original packing materials may cause product
damage that will void the warranty.
• Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life
support equipment or to significantly affect its safety or effectiveness is not recommended. Do not use this equipment in the presence of a
flammable anesthetic mixture with air, oxygen or nitrous oxide.
AFront Panel
BTop Cover with Lock
CSide Panels
DVent Tray
E2U Backplate
FCable Access Plates
GGround Wire
Model SRWF12U38 shown. Product dimensions will vary by model.
Low-Profile Wall-Mount SmartRack Enclosures provide convenient and secure vertical mounting for standard 19-inch rackmount equipment,
regardless of vendor, and ship fully assembled for quick and easy deployment in areas previously considered impossible for placement. Using
a modular design that easily assembles and disassembles, the enclosures support 8U (SRWF12U38) or 12U (SRWF16U38) of vertically
mounted equipment up to 38 inches deep and 4U of patch panels. Both units support up to 400 lb. maximum weight.
A
D
GF
F
B
C
E
C
16-04-227-9335C5.indb 2 9/2/2016 10:18:55 AM

3
4 Preparation
Caution! Read All Instructions and Warnings Before Installation!
Warning: Rack enclosures can be extremely heavy. Do not attempt to unpack, move or install the enclosure without assistance.
Use extreme caution when handling the enclosure. Be sure to follow all handling and installation instructions.
Do not attempt to install equipment without first stabilizing the enclosure.
4.1. Unpacking
Use at least two people to unpack the enclosure.
1Move shipping box to a firm, level surface.
2Open box and remove the corner protectors. Save all packing materials for later use unless certain they will not be required. Packing
materials are recyclable.
3With one person on each side, carefully lift the enclosure out of the box and place on a firm, level surface.
4Examine the enclosure for any damage or loose parts. Confirm all parts are present. If anything is missing or damaged, contact Tripp Lite
for assistance. Do not attempt to use the enclosure if it has been damaged.
4.2. Disassembly
1Remove Unit from Shipping Pallet and
Packaging 2Unlock and remove Cover
3Remove (2) #6-32 Locking Screws,
then lift and remove Front Panel 4Remove Vent Tray 5Remove (4) Screws, lift and remove Side Panels
16-04-227-9335C5.indb 3 9/2/2016 10:18:59 AM

4
5. Installation
The enclosure installation area must be able to withstand the weight of the enclosure and all mounted equipment.
Refer to the Specifications section for enclosure model weight and capacity.
5.1. Mounting the Backplate
Mounting the Backplate to a Wall
Note: If the installation requires running cables through a wall, first remove
one or both of the cable access panels prior to mounting the Backplate.
For Stud Mount
Locate solid studs, 16” on center, before marking top two locations
for pilot holes. Drill #22 (0.157” or 4 mm) pilot holes, then drive
two (2) M10, 5/16” or 3/8 x 2.0” long (minimum) bolts (not
included) into the Backplate slots, spaced nominally at 16” at
the top. Tighten the first two bolts A, and then drill holes for the
remaining two (2) M10, 5/16” or 3/8” bolts into the bottom corners
of the backplate B. Use a minimum of four (4) locations for full
payload rating of 400 lb.
For Other Surfaces
When installing to other surfaces, drive toggle bolts into a 3/4”
plywood-backed wall or fender washers and concrete tapping screws
(3/16” x 2-1/4” minimum) into cinder block.
WARNING
• When installing wall mounts onto a concrete masonry
unit (also known as a CMU or “cinder block”), verify
that the actual concrete thickness is at least 35 mm
(1 3/8”) in order to hold the concrete anchors. DO NOT
DRILL INTO MORTAR JOINTS! Be sure to mount Backplate
onto solid sections of the blocks. The solid sections can
generally be found 25 mm (1”) toward the middle of the
block from either end. An electric drill on a slow setting
is suggested to drill the hole rather than a hammer drill,
so as to avoid breaking out the back of the hole when
entering a hollow section.
• Installers must verify that the supporting surface will
safely support the combined load of the equipment and
all attached hardware and components.
2-Post Rack-Mount Installation
The SRWF12U38 and SRWF16U38 are also designed for 2-post rack
mounting. To attach, drive #12-24 screws (not included) through
the Backplate into the corresponding 2-post mounting holes. Use a
minimum of 10 locations for full payload rating of 400 lb.
A
B
A
B
16-04-227-9335C5.indb 4 9/2/2016 10:19:00 AM

5
5. Installation
5.2. Unit and Equipment Installation
1Side Panel Installation
After ensuring the Backplate is securely fastened to the wall or
2-post rack, install the Side Panels by inserting the Side Panel
hooks into the rectangular cutouts in the Backplate. Apply
downward pressure to properly seat the panels A.
Notes: The smooth surface of the Side Panels should face away from
one another.
All Side Panel hooks must be engaged for proper assembly.
After the Side Panels are seated, the top surface will be flush
with the internal 2U flanges in the Backplate. The bottom of the
Side Panels will be flush with the Backplate bottom. Two holes
for each Side Panel will align. Use four (4) supplied #12-24
screws for the two holes located in each Side Panel B. Ensure
all screws are firmly secured to the Backplate.
A
A
B
B
2Vent Tray Installation
Slide the Vent Tray into the side panels’ bottom slots. The right-
angle flanges of the Vent Tray should face upward toward the
cabinet’s interior.
16-04-227-9335C5.indb 5 9/2/2016 10:19:03 AM

6
5. Installation
3Front Panel Installation
Insert the Front Panel hooks into the rectangular cutouts in the
Side Panels. All hooks must be engaged for proper assembly.
Apply downward pressure to properly seat the panel. Secure the
Front Panel using (2) #6-32 Locking Screws.
Before installing the first piece of equipment,
make sure to temporarily install the Front Panel.
This allows uniform spacing of the Side Panels,
squares and aligns the cabinet, and ensures
proper seating of the locking cover. After the
first piece of equipment is securely installed,
the Front Panel and Vent Tray can once again be
removed to install any remaining equipment.
4Equipment Installation
With user-supplied standard rack hardware (#12-24 screws),
vertically mount up to 8U (SRWF12U38) or 12U (SRWF16U38)
of network equipment A, and up to 4U of patch panels
horizontally B.
5Cover Installation
Place cover onto the Side Panels and slide toward the
Backplate. When properly seated, the cover should be flush
against the Backplate and level with the top of the Backplate.
The cover may then be locked with either of the two (2) keys
provided.
A
B
16-04-227-9335C5.indb 6 9/2/2016 10:19:06 AM

7
6. Enclosure Configuration
8. Storage and Service
7. Specifications
6.1. Cable Access and Management
The top, bottom and sides of the cabinet contain rectangular openings (four total) for cable access and management. These can be opened or
closed by unscrewing or screwing the removable cable access panel.
For improved cooling efficiency and a cleaner installation appearnce, all cable access holes are compatible with Tripp Lite’s SRBRUSHWM
Brush Strip Plate accessory. The brush strip plate securely fits into the cable routing panel to block unwanted airflow. For more information, visit
www.tripplite.com.
6.2. Ground Connection
All parts of the enclosure are grounded to the frame. Use the enclosure’s front or rear threaded grounding point and an M6 screw to connect
the frame directly to your facility’s earth ground connection with an 8 AWG (3.264 mm) wire. Warning: Attach each enclosure to earth
ground separately. Do not use the enclosure without an earth ground connection.
Storage
The enclosure should be stored in a controlled indoor environment, away from moisture, temperature extremes, flammable liquids and gasses,
conductive contaminants, dust and direct sunlight. Store the enclosure in its original shipping container if possible.
Service
Your Tripp Lite product is covered by the warranty described in this manual. A variety of Extended Warranty and On-Site Service Programs are
also available from Tripp Lite. For more information on service, visit www.tripplite.com/support. Before returning your product for service, follow
these steps:
1. Review the installation and operation procedures in this manual to insure that the service problem does not originate from a misreading of
the instructions.
2. If the problem continues, do not contact or return the product to the dealer. Instead, visit www.tripplite.com/support.
3. If the problem requires service, visit www.tripplite.com/support and click the Product Returns link. From here you can request a Returned
Material Authorization (RMA) number, which is required for service. This simple on-line form will ask for your unit’s model and serial
numbers, along with other general purchaser information. The RMA number, along with shipping instructions will be emailed to you. Any
damages (direct, indirect, special or consequential) to the product incurred during shipment to Tripp Lite or an authorized Tripp Lite service
center is not covered under warranty. Products shipped to Tripp Lite or an authorized Tripp Lite service center must have transportation
charges prepaid. Mark the RMA number on the outside of the package. If the product is within its warranty period, enclose a copy of your
sales receipt. Return the product for service using an insured carrier to the address given to you when you request the RMA.
Model SRWF12U38 SRWF16U38
Total Rack Units 12U 16U
Patch Panel Rack Units 4U 4U
Equipment Rack Units 8U 12U
Backplate Depth 4.65 in. / 118 mm 4.65 in. / 118 mm
Unit Dimensions (H x W x D) 38 x 19.7 x 16 in. / 965 x 500 x 408 mm 38 x 19.7 x 23.1 in. / 965 x 500 x 587 mm
Unit Weight 66 lb. / 30 kg 81.5 lb. / 37 kg
16-04-227-9335C5.indb 7 9/2/2016 10:19:06 AM

8
9. Warranty and Product Registration
5-Year Limited Warranty
Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in material and workmanship for a period of
5 years from the date of initial purchase. If the product should prove defective in material or workmanship within that period, Seller will repair or replace the
product, at its sole discretion.
THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE, ABUSE OR NEGLECT. SELLER MAKES NO
EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED
WARRANTIES, INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE;
AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL DAMAGES. (Some states do not allow limitations on how long an implied
warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not
apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from jurisdiction to jurisdiction).
WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate or safe for the use intended. Since individual
applications are subject to great variation, the manufacturer makes no representation or warranty as to the suitability or fitness of these devices for any specific
application.
Product Registration
Visit www.tripplite.com/warranty today to register your new Tripp Lite product.You’ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite
product!*
* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
Regulatory Compliance Identification Numbers
For the purpose of regulatory compliance certifications and identification, your Tripp Lite product has been assigned a unique series number. The series number
can be found on the product nameplate label, along with all required approval markings and information. When requesting compliance information for this
product, always refer to the series number. The series number should not be confused with the marketing name or model number of the product.
Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice.
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
16-04-227-9335C5.indb 8 9/2/2016 10:19:06 AM

9
Manual del Propietario
Gabinetes
SmartRack®de bajo perfil
para instalar en la pared
Modelos: SRWF12U38, SRWF16U38
1111 W. 35th Street, Chicago, IL 60609 EE. UU. • www.tripplite.com/support
Copyright © 2016 Tripp Lite. Todos los derechos reservados.
Índice
1. Instrucciones de Seguridad Importantes 10
2. Descripción General 10
3. Identificación de Características 10
4. Preparación 11
4.1. Desempacado 11
4.2. Desarmado 11
5. Instalación 12
5.1. Instalación de la Placa de Respaldo 12
5.2. Instalación de la Unidad y el Equipo 13
6. Configuración del Gabinete 15
6.1. Acceso y Manejo de Cables 15
6.2. Conexión a Tierra 15
7. Especificaciones 15
8. Almacenamiento y Servicio 15
9. Garantía 16
English 1
Français 17
Русский
25
MÁS DE
16-04-227-9335C5.indb 9 9/2/2016 10:19:07 AM

10
1. Instrucciones de Seguridad Importantes
3. Identificación de Características
2. Descripción General
GUARDE ESTAS INSTRUCCIONES
Este manual contiene instrucciones y advertencias que deben observarse durante la instalación y la operación del producto
aquí descrito. El no hacerlo puede invalidar la garantía y causar daños a la propiedad o lesiones personales.
• Mantenga el gabinete en un entorno interior controlado lejos de humedad excesiva, temperaturas extremas, líquidos y gases inflamables,
contaminantes conductores, polvo o luz solar directa.
• Deje un espacio adecuado en la parte delantera y trasera del gabinete para una ventilación adecuada. No bloquee, cubra ni coloque objetos
en las aberturas externas de ventilación del gabinete.
• El gabinete es extremadamente pesado. Tenga cuidado al manejar el gabinete. No intente desempacarlo, moverlo o instalarlo sin ayuda.
Utilizar un dispositivo mecánico como un montacargas o gato para tarimas para mover el gabinete en el contenedor de embarque.
• No coloque objeto alguno sobre el gabinete, especialmente recipientes de líquido y no intente apilar los gabinetes.
• Inspeccione el contenedor de embarque y el gabinete para detectar daños en el embarque. No use el gabinete si está dañado.
• Deje el gabinete en el contenedor de embarque hasta que haya sido movido tan cerca de la ubicación de instalación final como sea posible.
• Instale el gabinete en un área estructuralmente firme o sobre un piso nivelado, capaces de soportar la carga del peso del gabinete, de todo
el equipo que se instale en el gabinete y otros gabinetes y del equipo que se instalen cerca.
• Tenga cuidado cuando corte el material de empaque. El gabinete podría haber sido rasguñado o rayado, causando daños no cubiertos por la
garantía.
• Guarde todo el material de empaque para uso posterior. Volver a empacar y enviar el gabinete sin el material de empaque original puede
ocasionar daños al producto que anularían la garantía.
• No se recomienda el uso de este equipo en aplicaciones de soporte de vida en donde la falla de este equipo pueda razonablemente causar
la falla del equipo de soporte de vida o afectar significativamente su seguridad o efectividad. No use este equipo en presencia de una
mezcla inflamable de anestésicos con aire, oxígeno u óxido nitroso.
APanel Frontal
BCubierta Superior con Cerradura
CPaneles Laterales
DCharola Ventilada
EPaca de Respaldo de 2U
FPlacas para Acceso del Cable
GConductor de Tierra
Modelo SRWF12U38 mostrado. Las dimensiones del producto
variarán por modelo.
Los gabinetes SmartRack de bajo perfil para instalar en la pared proporcionan instalación vertical conveniente y segura a los equipos para
instalación en rack estándar de 19", sin importar el proveedor, y se envían completamente ensamblados para una instalación rápida y fácil
en áreas previamente consideradas imposibles para la colocación. Usando un diseño modular que se ensambla y desensambla fácilmente, el
gabinete soporta 8U (SRWF12U38) o 12U (SRWF16U38) de equipo instalado verticalmente de hasta 38" de profundidad y 4U de paneles de
acoplamiento. Ambas unidades soportan hasta 181 kg [400 lb] de peso máximo.
A
D
GF
F
B
C
E
C
16-04-227-9335C5.indb 10 9/2/2016 10:19:07 AM