Triton Aquatronic manual power shower User manual

2180703J - OCT 2017
Installation and
operating
instructions
Aquatronic
manual
power shower
The showerhead and hose supplied with this product are an integral
part of the safety of your shower. Failure to use genuine Triton
parts may cause injury and will invalidate your warranty

Power shower
CONTENTS Page
Plumbing and electrical notes......................................................... 1
Introduction ................................................................................... 2
Safety warnings .............................................................................. 2
Main components .......................................................................... 3
Specifications.................................................................................. 3
Site requirements ........................................................................... 4
General installation notes ............................................................... 5
Siting of the shower ....................................................................... 6
Removing the cover........................................................................ 7
Plumbing connections .................................................................... 7
Fitting the shower to the wall........................................................ 10
Electrical connections .................................................................... 11
Commissioning.............................................................................. 12
Operating the shower.................................................................... 15
Adjusting the maximum temperature stop .................................... 16
Instructions for installers and service engineers only ...................... 17
Spare parts .................................................................................... 18
Fault finding ...............................................................................19 - 20
Water/Cable entry points diagram .................................... 21
Service policy, guarantee, etc. ..................................................rear cover
To check the product suitability for commercial and multiple installations, please contact Triton’s
specication advisory service before installation.
Telephone:
Facsimile:
E mail:
024 7637 2222
024 7632 4504
[email protected]
WARNING
This appliance can be used by children aged from 3years and above
and persons with reduced physical, sensory or mental capabilities or
lack of experience and knowledge if they have been given supervisi
on
or instruction concerning use of the appliance in a safe way and
understand the hazards involved. Children may not play with the
appliance. Cleaning and user maintenance shall not be made by
children.
Installers please note these InstructIons are to be left wIth the user

Power shower
1
1 PLUMBING NOTES
1.1 All installations must comply with Water
Regulations or Water Bylaws.
1.2 Supply pipes must be flushed to clear
debris before connecting the shower unit.
1.3 DO NOT connect the shower unit to
the mains cold water supply as it would
damage the unit and also, the installation
would be in breach of Water Regulations.
1.4 DO NOT use excessive force when making
connections to the flexible hose or
showerhead – finger tight is sufficient.
1.5 ALL plumbing connections are to be
completed and water supplies turned on
BEFORE switching on the electricity supply.
The shower must not be operated dry
without water.
1.6 DO NOT solder pipes or fittings within
300 mm of the shower appliance, as heat
transfer can damage components.
1.7 When installed, the top of the shower unit
must be at least 75 mm lower than the
base of the cold water storage cistern to
prevent the pump being run dry without
water.
1.8 A dedicated cold water supply must be
taken directly from the cold water cistern
to the shower. This draw-off must be on
the opposite side of the cistern to the float
operated valve to reduce the risk of air
entering the unit.
1.9 The action of the pump is to increase the
flow rate. If the supply pipework cannot
handle the resulting flow rate then:
1.9.1 The anticipated flow rate may not
be achieved.
1.9.2 Air may be drawn into the hot
supply from the vent pipe causing
spluttering and temperature fluctuations at
the showerhead.
1.10 Fullway isolating valves MUST be fitted
on the hot and cold water supplies to
the shower as an independent means
of isolating the water supplies should
maintenance or servicing be necessary. DO
NOT use stop taps or ball-o-fix type valves
which restrict flow.
2 ELECTRICAL NOTES
2.1 The installation must comply with BS 7671
‘Requirements for electrical installations’
(IEE wiring regulations). Make sure the
incoming hot and cold water supplies to
the shower are adequately earth bonded.
2.2 DO NOT turn on the electrical supply
until the plumbing connections have been
completed. Only then can the electricity be
switched on in order to power the solenoid
to turn water on to the shower when
commissioning. The shower must not be
operated dry without water.
2.3 The mains supply must be 230/240V, at
50Hz, connected to the unit via a double
pole switched 3 Amp fused connection
unit (not supplied) with a minimum 3 mm
contact separation gap in each pole.
2.4 In accordance with ‘The Plugs and Sockets
etc. (Safety) Regulations 1994’, this unit
is intended to be permanently connected
to the fixed electrical wiring of the mains
system.
2.5 Fuses do not give personal protection
against electric shock.
2.6 A 30mA residual current device (RCD)
MUST be installed. This may be part of the
consumer unit or a separate unit.

Power shower
2
INTRODUCTION
This book contains all the necessary fitting and
operating instructions for your Triton Power
Shower. Please read them carefully.
The shower installation must be carried out by
suitably competent person and in sequence of
this instruction book.
Care taken during the installation will ensure a
long and trouble free life from your shower
IMPORTANT: All plumbing connections must
be completed BEFORE making the electrical
connections.
Please read through the whole of this book
before beginning your installation.
IMPORTANT: The fittings on the pipe inlet
elbows are of the push-in type. The pipework
must be cut with a pipe cutter and all burrs
and rough edges removed from the end
of the tube. The fittings can be used with
copper and plastic pipe.
Where chrome plated pipe is used, remove
the first 25 mm of plating.
Note: The pump inside this product is rated
15 minutes on / 45 minutes off duty cycle.
SAFETY WARNINGS
a. DO NOT insert fingers into the push-in inlet
fittings. Doing so could cause injury.
b. Under no circumstances must this product
be connected to mains cold or hot water
supplies. Failure to comply will invalidate
the guarantee.
c. The shower MUST NOT be used if suspected
of being frozen.
d. The outlet of this appliance MUST NOT be
connected to any form of tap or fitting not
recommended by the manufacturer.
e. The showerhead cartridge MUST be cleaned
regularly to remove scale and debris.
f. This appliance MUST be earthed.
g. Switch off immediately at the isolating
switch if water ceases to flow during use.
h. DO NOT operate the shower outside the
guidelines laid out in ‘site requirements’.
A 30mA residual current device (RCD) MUST
be installed in all UK 230V electric and
pumped shower circuits. This may be part of
the consumer unit or a separate unit.
Replacement parts can be ordered from Triton
Customer Service. See ‘spare parts’ for details and part
numbers.
WARNING!
The power shower does not contain
a thermostatic valve – it will not shut
off in the event of failure of either
the hot or cold water supplies.

Power shower
3
Hot water temperature
Maximum temperature 65°C.
BS 6700 recommends that the temperature
of stored water should never exceed 65°C. A
stored water temperature of 60°C is considered
sufficient to meet all normal requirements and
will minimise the effects of scale in hard water
areas.
Maximum static inlet pressures
100 Kpa (1 bar) or 10m (supplies must be
gravity fed at nominally equal pressures).
Minimum static inlet pressure
0.75 Kpa (0.0075 bar) or 75mm (required to
prime the integral centrifugal pump).
Maximum supply head 10m.
SPECIFICATIONS
MAIN COMPONENTS
1. Top pipe entry and cable entry
2. Terminal block
3. Cover screw fixing
4. Motor retaining bracket
5. Rear pipe entry and cable entry
6. Wall fixing holes
7. Pipe inlet elbow - top
(contains single check valves)
8. Filter cover - top
9. Pump
10. PCB
11. Temperature control valve
12. Solenoid
13. Filter cover - bottom
14. Pipe inlet elbow - bottom
(contains single check valves)
15. Outlet
16. Bottom pipe entry
17. Potentiometer gear
Fig.1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15 16
17
Entry Points
Water – Right: bottom, top back.
Cable – Right: top back.

Power shower
4
Fig.3 illustrates all the incorrect connections that
must be avoided.
All pipework to the shower unit must be routed
where it remains below the level of water in
the cistern. In the case of horizontal sections
of pipework in lofts, it may be necessary to
fit automatic air vents at high points on the
supplies to remove the possibility of air locks.
For the operation of the shower only, it is
recommended that the cold water storage
cistern is capable of holding at least 114 litres
(25 gallons). Where other hot and cold outlets
are likely to be in use simultaneously, the storage
capacity should be increased to 228 litres (50
gallons) in accordance with BS 6700.
Do ensure compliance with the Water
Regulations/Bylaws.
DO NOT connect to a combination cylinder
unless there is a guaranteed 114 litre cold supply
to the cylinder as the shower can deliver up to
14 litres per minute. It is advisable to check that
Mains supply
Isolating
valve Cold water cistern
Vent pipe tee
Isolating
valve Hot supply
Hot water
cylinder
Drain
valve
Other hot water
draw-offs
Alternative
connection
Shower unit
Ring main
25mm min
Isolating spur
(3A fused)
outside bathroom
Dedicated cold supply
10m
max
75mm
min
Isolating
valves
SITE REQUIREMENTS
Water
The installation must be in accordance with
Water Regulations/Bylaws and BS 6700.
For correct operation of this shower unit, both
hot and cold water supplies to the appliance
must be gravity fed, at nominally equal
pressures, from a cold water storage cistern and
a hot water storage cylinder.
The water circuit should be installed so that the
flow is not significantly affected by other taps
and appliances being operated elsewhere on the
premises.
Fig.2 shows a recommended installation where
the hot water supply for the shower is made
via a tee connection on the underside of the
horizontal section of pipework from the cylinder.
Alternatively, the connection can be taken from
the hot supply pipe to other outlets as long as it
is the first draw-off below the ventilation pipe tee.
Fig.2 (Diagrammatic view – not to scale)

Power shower
5
the infill rate from the float operated valve meets
the output requirements..
It is recommended that there is a minimum
of approximately 114 litres (25 gallons) of hot
water storage per appliance.
The shower MUST NOT be connected to the
mains cold water supply.
DO NOT use jointing compounds.
GENERAL INSTALLATION NOTES
1. DO NOT take risks with plumbing or
electrical equipment.
2. DO NOT install this unit in a position where
it could become frozen.
3. Isolate electrical and water supplies BEFORE
proceeding with installation work.
4. Shower control MUST be fed from a cold
water storage cistern and hot water cylinder
that provides nominally equal pressures.
Depicting incorrect connections
Hot feed
connection
from
horizontal
vent pipe
No isolating
valves
Soap dish
retaining ring
not used
High level
hot feed
Hot feed connection
above vent tee
Cold supply from
cylinder feed
Drain
valve
Hot water
cylinder
Other cold
draw-offs
from shower
supply
Supply taken
from mains
Mains supply
Cold water cistern
Cold supply on same side
as float valve and above
cylinder cold feed
Fig.3 (Diagrammatic view
not to scale)
5. The unit must be mounted onto the finished
wall surface (on top of tiles).
DO NOT tile up to the unit after fixing to
the wall.
6. If installing with rear inlet supplies, it is
recommended the supply pipework is sealed
to the wall so as to prevent water from
leaking back into the wall.
7. In solid wall installations, the supply
pipework should be housed within
ducting in order to allow some free lateral
movement when making connections and
to ensure compliance with requirements of
accessibility of pipes and pipe fittings.
Fig.4 shows a schematic wiring diagram of the unit.

Power shower
6
Shower can
be mounted
either side of
the riser rail
Spill-over
level
Ceiling
Use soap dish
retaining ring
Height of
sprayhead
and shower
to suit user’s
requirement
Shower unit
must not be
within an area
1 metre
from base
Space for cover
screw access
Fig.5
SITING OF THE SHOWER
IMPORTANT: If fitting to a tiled wall, always
mount the unit on the surface of the tiles.
NEVER tile up to the unit.
Refer to fig.5 for correct siting of the shower.
Position the unit vertically where it will NOT
be in direct contact with water from the
showerhead.
Note: Allow sufficient room between the ceiling
and the shower unit to access the top cover
screw.
Position the shower and showerhead on the wall
so that all controls can be comfortably reached
when using the shower.
The showerhead and riser rail can be positioned
either side of the shower unit.
Note: Water Regulations require the showerhead
be ‘constrained by a fixed or sliding attachment
so that it can only discharge water at a point
not less than 25 mm above the spill-over level
of the relevant bath, shower tray or other fixed
appliance’. The use of the supplied soap dish will
in most cases meet this requirement, but if the
showerhead can be placed within a bath, basin
or shower tray, then a device must be fitted to
prevent back-flow.
L E N
Potentiometer
Switch
Solenoid
Motor
Capacitor 2
RFI suppression coil
Capacitor 1
PCB
Thermal
fuse
AS2000T/AS2000 schematic wiring schematic
Fig.4 (schematic view )
WARNING!
The shower must not be positioned
where it will be subject to freezing
conditions.

Power shower
7
Fig.6
REMOVING THE COVER
To remove the cover, first pull off the cover trim
(fig.6) to reveal the retaining screw.
Undo the screw and pull off the inner
temperature control. Now remove the outer flow
control assembly comprising of the flow control,
maximum temperature stop and temperature
disc (fig.7).
Note: If adjustment of the maximum
temperature stop is required, refer to section
’Adjusting the maximum temperature stop’.
Remove the two cover fixing screws – top and
bottom (fig.8).
Carefully lift the cover away from the backplate.
Lay aside the cover and screws until the unit is
fully installed.
Note: When removing the cover for future
maintenance purposes be aware of the lead
connecting the Start/Stop switch to the PCB
harness. To release, squeeze the connection
block arms and pull apart. DO NOT let the unit
dangle by the lead.
PLUMBING CONNECTIONS
Plumbing to be carried out before wiring
Note: The outlet of the shower must not be
connected to anything other than the hose and
showerhead supplied.
DO NOT use jointing compounds on any pipe
fittings for the installation.
When connecting pipework avoid using tight
90° elbows. Swept or formed bends will give
optimum performance.
Isolate the mains water supply to the cold water
cistern. Drain the hot and cold pipes by opening
all taps.
The hot water supply can be taken from the hot
supply pipe from the cylinder. Make sure that it
is the first draw-off below the ventilation pipe
tee in order to minimise the effects of water
draw-off elsewhere in the house (see fig.2).
Note: There must not be any other draw-offs
between the take-off point and the shower.
A dedicated cold water supply must be taken
directly from the cold water cistern to the
shower. This draw-off must be positioned
Temperature
disc
Flow
control
Maximum
temperature
stop
Fig.7
Fig.8

Power shower
8
25 mm below the cold feed connection to the
hot water cylinder on the opposite side of the
cistern to the float operated valve (see fig.2).
This minimises air ingress into the pipework.
Plumbing options other than those outlined
in these fitting instructions could impair the
performance. For example, if hot and cold
connections are made after draw-off points
to other outlets, (eg. washing machine, taps,
etc.) it could result in unstable flows and
temperatures should other appliances operate at
the same time.
Run the hot and cold pipework to the shower
position, making sure that the pipework does
not rise above the level of water in the cold
cistern at any point to avoid air locks. Under
normal site conditions 15 mm pipework will be
adequate.
Decide the position of the shower. Cut the
pipework to the dimensions relevant to the
chosen direction of water entry into the shower.
IMPORTANT: For rear entry only, the supplied
elbows must be used. For ease of installation,
the backplate area adjacent to the top pipe
inlet must be cut out, including the top left
wall fixing hole.
When fitting the elbows to incoming pipework,
ensure the elbow collets are fully engaged with
the pipe.
Dimensions are shown in fig.9 and fig.10.
Note: The pipe inlets are marked for hot and
cold connections – left-hand side for hot inlet on
bottom entry (fig.11), but right-hand side for
hot inlet on top or rear entry (fig.12).
IMPORTANT: The fittings on the inlet elbows
are the push-in type. The pipework must
be cut with a pipe cutter and all burrs and
rough edges removed from the end of the
tube. The fittings can be used with copper
and plastic pipe.
If using chrome plated copper pipe, remove
the first 25 mm of plating completely from
the connecting surfaces. If not completely
removed then the collet will not grip the
pipe and under pressure the pipe may be
forced out.
Hot
19 mm
98 mm
26 mm
Wall
Cold
Rear edge
of
backplate
Fig.9
Top
19 mm
26 mm
Cold Hot
Area of
backplate
to remove
Wall
5 mm
Pipe protruding
from wall
19 mm
34 mm
26 mm
Rear edge
of
backplate
Hot Cold
Wall
Rear
23.5 mm
Bottom
Fig.10

Power shower
9
Note: Pipework must be clipped or fixed to the
wall so that it cannot be moved or removed
without the aid of a tool.
Note: The pipe inlets contain filters. These
should be periodically removed and cleaned
in order to maintain the performance of the
shower. See section ‘cleaning’ on how to access
the filters.
IMPORTANT: The inlets contain check valves,
so before completing the connection of the
water supplies to the shower flush out the
pipework to remove all swarf and system
debris that may cause damage to internal
parts. This can be achieved by connecting
a hose to the pipework and turning on the
water supplies long enough to clear the
debris to waste.
IMPORTANT: Two factory fitted blanking
plugs are fitted to the top pipe inlets. These
should be left in position if bottom pipe entry
is required.
For top or rear pipe entry, the two plugs
MUST be removed and refitted into the
bottom pipe inlets. Failure to fit the
blanking plugs will result in the unit working
erratically.
Insert the pipe removal tool supplied between
the flange of the plug and the grey collet and
lever the plug outward (fig.13). Whilst holding
back on the collet, pull out each plug by hand.
When refitting the plugs in the bottom pipe
inlets, make sure they are pushed fully home.
Note: The unit is supplied with a splash guard
(fig.14) to prevent water ingress when top
entry pipework is used. If fitting top entry
pipework, make sure the splash guard is
correctly fitted (fig.14) before replacing the
cover.
Bottom
(rising)
supply
Top
(falling)
or rear
supply
Hot
side
Hot
side
Bottom
(rising)
supply
Top
(falling)
or rear
supply
Hot
side
Hot
side
Fig.11
Fig.12
Blanking
plug
Fig.13
Splash guard
Fig.14

Power shower
10
FITTING THE SHOWER TO THE WALL
IMPORTANT: Before fitting the shower,
make sure the pipework is flushed out to
remove all debris, flux, etc.
For top pipe entry or top cable entry, remove
the relevant cut-outs by either breaking out or
by using a knife or junior hacksaw (fig.15).
If top entry for both pipe and cable is required,
then additionally remove the shaded area
(fig.15) by using a knife or junior hacksaw.
For bottom pipe entry, remove the cut-out and
break off the two circular parts (fig.16). Replace
the cut-out.
For rear pipe entry only, the supplied elbows
must be used with the necessary portion of
backplate cut away as shown in fig.9.
It will be necessary if rear cable entry is required,
for conduit or other routing of the electrical
cable to be completed before fixing the shower
to the wall.
Offer the backplate unit up to the completed
pipework and manoeuvre so that the end of the
pipes enter fully into the inlet fittings.
Mark positions for wall fixing holes using
backplate as template (fig.17). Note that four
fixing holes are provided but using only two
should be adequate for most site conditions.
Using the pipe removal tool supplied, push back
and hold the collets from the pipework (fig.18)
to disengage the pipework from the inlet elbows.
Remove unit from the wall.
Drill and plug the wall.
(An appropriate drill bit should be used. If the
wall is brick, plasterboard or a soft building block,
appropriate wall plugs and screws should be fitted).
Note: If fitting rising supplies to the unit, ensure
debris does not enter the pipes when drilling the
wall.
Offer the backplate unit up to the completed
pipework and manoeuvre so that the end of the
pipes enter fully into the inlet fittings.
Check the backplate is square and the fixing
holes are aligned then secure the shower
(fig.17).
Remove shaded area
Cut out
for cable
Fig.15
Fig.16
Fig.17

Power shower
11
ELECTRICAL CONNECTIONS
The supply cable must conform to relevant
tables in current IEE regulations. In most cases
1 mm² twin and earth will be adequate.
The electrical rating of the shower is on the
rating label within the unit.
SWITCH OFF THE ELECTRICITY SUPPLY AT
THE MAINS.
Cable entry points are shown in fig.1. Conduit
entry can only be from the rear.
Route the cable into the shower, taking care to
avoid the area of the wall fixings and connect to
the terminal block (fig.19) as follows:
Earth cable to terminal marked E
Neutral cable to terminal marked N
Live cable to terminal marked L
IMPORTANT: Fully tighten the terminal block
screws and check that no cable insulation is
trapped under the screws.
Note: The supply cable earth conductor must
be sleeved.
A 30mA residual current device (RCD) MUST be
installed in the shower circuit. This may be part
of the consumer unit or a separate unit.
DO NOT switch on the electricity supply until
the water has been turned on to the unit and
connections have been tested for leaks.
IMPORTANT: The cover may be left off
initially only for commissioning.
Fig.18
Terminal block
Fig.19
WARNING!
This unit must be earthed. Isolate the
supply before starting.

Power shower
12
COMMISSIONING
The first operation of the shower is intended to
flush out any remaining system debris and to
ensure water is purged through the unit. This
operation must be carried out with the flexible
hose screwed to the shower outlet but without
the sprayhead attached.
Make sure the outlet of the flexible hose is
directed to waste.
Check the isolating valves controlling the water
supply to the unit are fully open.
Note: There is no need to fit cover at this stage
but be aware of live parts when the electricity is
switched on temporarily.
Fit the temperature control onto the splined
spindle (fig.20).
On the PCB, make sure the commissioning link is
positioned on the middle two pins (fig.21).
Switch on the electric supply at isolating switch.
Water will begin to flow under gravity pressure.
(Once the unit has been commissioned,
disconnect the electricity supply before removing
the commissioning link).
In order to dispel air and to prime both supplies
to the shower unit, turn the temperature control
several times within its rotational limits. ONCE
RESISTANCE IS FELT, DO NOT FORCE THE
CONTROL FURTHER.
WARNING!
Before normal operation of the
shower, it is essential that the
commissioning and setup procedure
are correctly completed. Failure to do
so could cause the pump to run dry
without water and invalidate your
guarantee.
WARNING!
Be aware of live parts in the unit
when the electricity is switched on.
DO NOT tamper with any parts and
DO NOT deviate from the following
instructions.
Temperature control
Fig.20
Commissioning
link
Fig.21
Hot Cold
Fig.22

Power shower
13
Note: The temperature control rotates less than
one complete turn (fig.22). DO NOT force it
beyond these limits.
To stop the water flow, switch off the electricity
supply at the isolating switch.
Check for leaks in the pipework and remedy
if necessary. If rear entry has been used then
seal around pipes with mastic to prevent the
possibility of water entering the wall cavity.
DO NOT use plaster as this could cause difficulty
if maintenance is required later.
Setup procedure
MAKE SURE THE ELECTRICITY TO THE UNIT IS
SWITCHED OFF.
Pull off the temperature control. Remove the
commissioning link from the PCB (fig.23) and
store safely for future use.
Attached to the flow control potentiometer is a
4-wire lead. Fit the connector on the end of this
lead to the 4 pins on the PCB (fig.24) – it can
fit either way.
Make sure the potentiometer control is in the
‘off’ position – fully anti-clockwise (fig.25).
Replacing the cover
Fit the cover, making sure the connector is fitted
to the PCB and the wires are clear of obstructions.
Secure with the top and bottom fixing screws
(fig.8).
With your fingers, rotate the valve spindle fully
anti-clockwise (fig.26) to the fully hot position.
Replace the flow control so that it aligns with
the ‘stop’ position.
Fit the temperature disc (it will only fit one way)
and maximum temperature stop (fig.27).
WARNING!
Once the unit has been commissioned,
turn off the electricity supply at
the mains before removing the
commissioning link.
Fig.23
Fig.24
Fig.25
Fig.26

Power shower
14
Note: If adjustment of the maximum
temperature stop is required, refer to section
’Adjusting the maximum temperature stop’.
Replace the temperature control onto the valve
spindle. Make sure the pointer aligns with
setting ‘9’ on the temperature disc (fig.28).
Secure with the retaining screw and fit the cover
trim.
Switch on the electricity supply at the isolating
switch. Make sure both water supplies are still
turned on.
Once the installation of the riser rail is complete,
the shower is ready for normal operation.
Retaining
screw
Maximum
temperature
stop
Flow
control
Temperature
disc
Temperature
control
Cover
trim
Fig.28
Fig.27
WARNING
COVER RETAINING SCREWS
ONLY the SUPPLIED SCREWS should be
used. The use of none supplied screws WILL
invalidate product specications & warranty.

Power shower
15
OPERATING THE SHOWER
Check all plumbing and electrical supplies are
connected and switched on.
To start the shower, rotate the flow control
anti-clockwise from the ‘stop’ position (fig.29).
Adjust the control until the flow rate is
satisfactory.
For maximum flow, turn the flow control fully
anti-clockwise to the ‘max’ position.
To adjust the temperature, rotate the control
(fig.30). The temperature is numbered for ease
of use. The temperature ranges from-‘1’ – fully
cold to ‘9’ – fully hot.
Once the preferred temperature is reached, no
further adjustment is required, providing the hot
and cold water supplies remain constant.
To stop the shower, return the flow control
to the ‘stop’ position by rotating clockwise
(fig.31). This stops the pump and water flow.
Unless the shower is to be used again
immediately, the shower should also be switched
off at the electricity isolating switch.
As a safety feature, the temperature control
has a built-in stop to prevent you accidentally
exceeding your highest desired temperature. If
adjustment is required see section ‘Adjusting the
maximum temperature stop’.
To override this stop, depress the button
(fig.32) while the control is up against the stop
and turn the control anti-clockwise to the higher
settings (pressing the button before the stop will
not operate the override mechanism even if the
control is turned with the button depressed).
To return to the normal temperature range just
turn the temperature control clockwise until it
is past the maximum temperature stop. Make
sure the temperature control is in the normal
temperature range when the shower is switched
off. The stop comes in a factory set position
based on 65°C stored hot water temperature.
Note: As the flow control is adjusted it is normal
for the sound of the pump to alter in pitch.
Flow
control
Flow
control
Temperature
control
Override
button
Temperature
control
Fig.29
Fig.31
Fig.30
Fig.32

Power shower
16
ADJUSTING THE MAXIMUM
TEMPERATURE STOP
As a safety feature the shower has a built-in
maximum temperature stop to prevent you
accidentally exceeding your highest desired
temperature. This is set in the factory to provide
a maximum temperature based on the hot
and cold water supplies being 65°C and 15°C
respectively.
IMPORTANT: Only adjust the maximum
temperature stop when the hot water is at its
usual storage temperature.
Procedure
Rotate the temperature control to setting ‘9’ on
the temperature disc - fully hot position.
Remove the cover trim to reveal the retaining
screw (fig.33).
Undo the screw and carefully pull off the
temperature control, making sure it is still
aligned to setting ‘9’. Now remove the
maximum temperature stop.
To increase the temperature stop setting,
reposition the mechanism anti-clockwise within
the arc of the grooves (fig.34).
To decrease the temperature stop setting,
reposition the mechanism clockwise within the
arc of the grooves (fig.34).
Replace the temperature control onto the valve
spindle. Make sure the pointer aligns with
setting ‘9’ on the temperature disc (fig.28).
Secure with the retaining screw and refit the
cover trim.
Fig.33
Maximum
temperature
stop
Increase stop position
Decrease stop position
Fig.34

Power shower
17
CLEANING THE FILTERS
Note: Turn off the electricity and both hot
and cold water supplies to the unit before
proceeding further.
To remove the cover, first pull off the flow knob
cover trim (fig.6) to reveal the retaining screw.
Undo the screw and pull off the temperature
control. Now remove the outer flow control
assembly comprising of the flow control,
maximum temperature stop and temperature
disc.
Remove the two cover fixing screws – top
and bottom (fig.8). Carefully lift the cover
away from the backplate. To release the
PCB connector, squeeze the connection block
arms and pull apart.
Remove the single retaining screw from either
the upper or lower filter cover (fig.35),
depending upon whether top/rear entry or
bottom entry is used. Pull off the filter cover.
Carefully hook out the filters together with ‘O’
rings. Thoroughly clean and replace making sure
the ‘O’ rings are in position.
Refit the filter cover and secure with the
retaining screw.
Make sure the potentiometer control is rotated
fully anti-clockwise (fig.25).
With your fingers, rotate the valve spindle fully
anti-clockwise (fig.26) to the fully hot position.
Fit the cover, making sure the PCB connector is
fitted and the wires are clear of obstructions. Secure
with the top and bottom fixing screws (fig.8).
Replace the flow control so that it aligns with
the ‘min’ position.
Fit the temperature disc (it will only fit one way)
and maximum temperature stop (fig.27).
Replace the temperature control onto the valve
spindle. Make sure the pointer aligns with
setting ‘9’ on the temperature disc (fig.28).
Secure with the retaining screw and fit the cover
trim.
Switch on the electricity supply to the unit and
then turn on both water supplies.
INSTRUCTIONS FOR INSTALLERS AND SERVICE ENGINEERS ONLY
Retaining screw
Filter cover
Filter
Filter
Upper filter shown Fig.35
WARNING!
Switch off the electricity supply
and turn off both hot and cold
water supplies to the unit before
proceeding further.

Power shower
18
SPARE PARTS
Ref. Description Part No.
1 Terminal block........................... 22001320
2 Plastic inlet elbow plug.............. 7052140
3 Pump and motor assembly........ 84000130
4 Pipe inlet elbow ........................83305320
c/w filters and check valves
5 Temperature valve.....................83305280
6 Link pin .....................................22009060
7 PCB unit....................................7073738
8 Solenoid assembly ....................22012190
9 Gear.......................................... 7052184
10 Filter (pair) ................................83305330
11 Cover assembly .........................P22750600
–Pipe trim ................................... 7052146
–Pipe removing tool....................7052144
–Potentiometer ...........................82300860
–Bracket......................................7052183
–Wire kit ..................................... 83311260
–Maximum temperature stop......7052186
–Temperature control..................P09421000
c/w override button
–Flow control..............................7053263
–Temperature disc.......................7053266
–Temperature control trim ..........7053267
11
1
3
4
5
6
7
8
9
10
2