Triton TWX7 Assembly instructions

Version date: 14.03.19
tritontools.com
TWX7 CS002
Operating & Safety Instructions
TWX7
Contractor Saw
取扱説明書
972434_Manual.indd 1 14/03/2019 11:44

2
12 16 15 3
4
1
5
6
7
8
9
10
11
12
23
5
17
6
9
10
11
12
62
13
14
64
63
4
972434_Manual.indd 2 14/03/2019 11:44

3
4
5
8
12 11
17
9
2818
19
14
13
1
9
10
17
20
2
3
972434_Manual.indd 3 14/03/2019 11:44

4
22 21
12
2936
16
32
34 33 3112
23
25
26
13
35
9
27
24
13
13
9
6
5
15
7
18
17
30
7
14
24
23
14
64
972434_Manual.indd 4 14/03/2019 11:44

5
61
43 44 45
37
38
47
39
41
40
42
46
972434_Manual.indd 5 14/03/2019 11:44

6
4956 50
52
51
53
54
55
56
59
58
5748
60
972434_Manual.indd 6 14/03/2019 11:44

7
A
Initial set-up
最 初 の セットアップ
972434_Manual.indd 7 14/03/2019 11:44

8
B
Module insertion
ユニットの取り付け
C
Module locks & side-handle cover installation
ユニットロック & サイドハンドルカバーの
取り付け
WARNING: Do not place fingers and/or body parts
between the module and the Workcentre chassis.
警告: ユニットとワ ー クセンター の シャー シ
の間に、手や指や体の一部を置かないでください。
972434_Manual.indd 8 14/03/2019 11:44

9
D
Level adjustment
水平度の調整
1
2
3
48
9
10
5
6
7
972434_Manual.indd 9 14/03/2019 11:44

CM
1
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
20
2
0
10
E
Level adjustment straight edge
定規などの真っ直ぐなものを使った調整
F
Kerf plate removal
カ ーフプ レ ー トの 取 り 外 し
WARNING: Ensure the Kerf Plate (29) is installed and levelled correctly before use.
警告: ご使用になる前に、必ずカーフプレート（29）が正しく取り付けられ、水
平に調整されていることを確認して下さい。
972434_Manual.indd 10 14/03/2019 11:44

11
G
Riving knife installation
ライヴィングナイフ（割刃）の取り付け
3
2
1
972434_Manual.indd 11 14/03/2019 11:44

12
A
45°
0°
H
Blade calibration
ノコ刃の目盛補正
63
62
972434_Manual.indd 12 14/03/2019 11:44

13
I
Anti-kickback & guard assembly. Anti-kickback:
キックバック防止爪 & ノコ刃ガード。 キックバック防止爪:
2
4
1
3
972434_Manual.indd 13 14/03/2019 11:44

14
I
Anti-kickback & guard assembly. Blade guard:
キックバック防止爪 & ノコ刃ガード。 ノ コ 刃 ガ ー ド :
2
4
6
1
3
5
972434_Manual.indd 14 14/03/2019 11:44

15
J
Rip fence installation
リップフェンス の 取 り 付 け
K
Protractor gauge installation/use
マイターゲージの取り付けと使用
972434_Manual.indd 15 14/03/2019 11:44

16
L
Switchbox
スイッチ ボックス
M
Blade assembly
ノコ刃 の 組 み 立て
972434_Manual.indd 16 14/03/2019 11:44

17
N
Blade height winder
gear cover
ノコ刃高さ調整ワインダ
ーのギアカバー
O
Push-stick holder assembly
プッシュスティックホルダーの組み立て
2
4
1
3
972434_Manual.indd 17 14/03/2019 11:44

18
P
Cleaning the dust chute
集 塵 用 ダ ストシュート
の掃除
972434_Manual.indd 18 14/03/2019 11:44

19
972434_Manual.indd 19 14/03/2019 11:44

20
GB
VVolts
~, a.c. Alternating current
A, mA Ampere, milli-Amp
n0No load speed
ØDiameter
°Degrees
Technical Abbreviations Key
Wear hearing protection
Wear eye protection
Wear breathing protection
Wear head protection
Wear hand protection
Read instruction manual
Be aware of kickback!
Warning: Sharp blades or teeth!
Indoors use only!
DO NOT use in rain or damp environments!
WARNING: Moving parts can cause crush and cut injuries.
Caution!
Toxic fumes or gases!
DO NOT touch! DO NOT access the guard without removing the power. Keep
children and bystanders away while operating a power tool. Distractions can
cause you to lose control. All visitors should be kept safe distance from work
area.
Always disconnect from the power supply when adjusting, changing accessories,
cleaning, carrying out maintenance and when not in use!
Environmental Protection
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your local authority or retailer
for recycling advice.
Conforms to relevant legislation and safety standards.
Double insulation
Description of Symbols
The rating plate on your tool may show symbols. These represent important information about
the product or instructions on its use.
Specification
Model number: TWX7CS002
Voltage: 100V~, 50/60Hz
Power: 1350W
Run time: 30min
Ingress protection: IP20
No load speed: 4200min-1
Carbide metal saw blade: 254 x 25.4 x 2.6mm x 40P
Saw blade requirements: Diameter: Ø254mm
Min Body thickness: 1.7mm
Min – Max kerf: 2.4-2.7mm
Arbor: Ø25.4mm
Riving knife thickness: 2.2mm
Contractor saw module size L x W x H: 680 x 465 x 560mm
Max rip cut capacity: 775mm
Max Cutting depth at 0°
(perpendicular):
83mm
Max. Angle cuts at 45°: 57.5mm
Table with side extension width: +600mm
Table with outfeed extension length: +670mm
Max. workpiece size L x W: 851 x 775mm (without additional side
support and outfeed support)
Dust extraction port sizes: Blade Guard Dust Port inner dia: 34mm
Dust Extraction Port inner dia: 57.5mm
Dust Extraction Port Adaptor inner dia:
30mm
Weight 23.2kg
Combined weight (TWX7 & TWX7CS002): 48.3kg
Sound and vibration information:
Sound pressure LPA 95.5dB(A)
Sound power LWA 108.5dB(A)
Uncertainty K 3dB
The sound intensity level for the operator may exceed 85dB(A) and sound protection
measures are necessary.
Thank you for purchasing this Triton tool. This manual contains information necessary
for safe and effective operation of this product. This product has unique features and,
even if you are familiar with similar products, it is necessary to read this manual
carefully to ensure you fully understand the instructions. Ensure all users of the tool
read and fully understand this manual.
Original Instructions
Introduction
Hz Hertz
W, kW Watt, kilowatt
/min or min-1 (revolutions or
reciprocation) per
minute
dB(A) Decibel – A weighted
m/s2Vibration magnitude
972434_Manual.indd 20 14/03/2019 11:44