Trotec BZ01 User manual

TRT-BA-BZ01-TC2021-26-001-EN
BZ01
EN
OPERATING MANUAL
DIGITAL ALARM CLOCK WITH
ROOM CLIMATE CONTROL

2 EN
digital alarm clock with room climate control BZ01
Table of contents
Notes regarding the operating manual.................................2
Safety .....................................................................................2
Information about the device................................................3
Transport and storage...........................................................5
Operation ...............................................................................5
Maintenance and repair ........................................................8
Disposal .................................................................................8
Notes regarding the operating manual
Symbols
Warning of electrical voltage
This symbol indicates dangers to the life and health of
persons due to electrical voltage.
Warning
This signal word indicates a hazard with an average
risk level which, if not avoided, can result in serious
injury or death.
Caution
This signal word indicates a hazard with a low risk
level which, if not avoided, can result in minor or
moderate injury.
Note
This signal word indicates important information (e.g.
material damage), but does not indicate hazards.
Info
Information marked with this symbol helps you to carry
out your tasks quickly and safely.
Follow the manual
Information marked with this symbol indicates that the
operating manual must be observed.
You can download the current version of the operating manual
and the EU declaration of conformity via the following link:
BZ01
https://hub.trotec.com/?id=45272
Safety
Read this manual carefully before starting or using the
device. Always store the manual in the immediate vicinity
of the device or its site of use.
Warning
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may
result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
• Do not use the device in potentially explosive rooms or
areas and do not install it there.
• Do not use the device in aggressive atmosphere.
• Do not immerse the device in water. Do not allow liquids to
penetrate into the device.
• The device may only be used in dry surroundings and must
not be used in the rain or at a relative humidity exceeding
the operating conditions.
• Protect the device from permanent direct sunlight.
• Do not remove any safety signs, stickers or labels from the
device. Keep all safety signs, stickers and labels in legible
condition.
• Do not open the device.
• Observe the storage and operating conditions (see
Technical data).

EN 3
digital alarm clock with room climate control BZ01
Intended use
To use the device for its intended use, only use accessories and
spare parts which have been approved by Trotec.
Foreseeable misuse
Do not use the device out of doors.
Do not use the device in potentially explosive areas.
Any unauthorised changes, modifications or alterations to the
device are forbidden.
Personnel qualifications
People who use this device must:
• have read and understood the operating manual, especially
the Safety chapter.
Residual risks
Warning of electrical voltage
There is a risk of a short-circuit due to liquids
penetrating the housing!
Do not immerse the device and the accessories in
water. Make sure that no water or other liquids can
enter the housing.
Warning of electrical voltage
Work on the electrical components must only be
carried out by an authorised specialist company!
Warning
Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
Warning
The device is not a toy and does not belong in the
hands of children.
Warning
Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way!
Observe the personnel qualifications!
Caution
Keep a sufficient distance from heat sources.
Note
To prevent damages to the device, do not expose it to
extreme temperatures, extreme humidity or moisture.
Note
Do not use abrasive cleaners or solvents to clean the
device.
Information about the device
Device description
The digital alarm clock with room climate control is a battery-
powered measuring device for displaying the time as well as the
indoor climate.
It comes with the following functional properties and equipment
features:
• Simultaneous indication of room temperature, weather
forecast, humidity level, date, weekday and time or
calendar year
• Alarm with snooze function
• Hourly time signal
• Indication of recorded minimum and maximum values for
temperature and relative humidity
• Switching option between °C and °F

4 EN
digital alarm clock with room climate control BZ01
Device depiction
1
3
6
2
5
4
7
89
11
1213
10
No. Designation
1Weather forecast indication
2°C/ °F indication
3Relative humidity indication
4Weekday display
5Indication of time/ alarm time/ calendar year
6Indication of date/ alarm mode
7MODEbutton
8SETbutton
9UPbutton
10 SNZbutton
11 RESETbutton
12 Battery compartment
13 Bracket for wall mounting
Technical data
Parameter Value
Model BZ01
Article number 3.510.205.000
Weight (incl.
batteries)
approx. 72g
Dimensions
(heightx widthx
depth)
approx. 36mmx 82mmx 55mm
Display LCD (monochrome)
Power supply 1x Battery, typeAAA, 1.5V
Relative humidity
Measuring range 20% to99%RH,
"LL" is displayed ifRH is below20%
Accuracy ±5%RH
Resolution 1%
Air temperature
Measuring range -10°C to 50 °C or 14°C to 122 °C
Accuracy ±1°C or ±1.8°F
Measuring range
resolution
1 °C/°F
Ambient conditions
Operation -10°C to 50°C or 14°F to 122°F
and 90%RH (non-condensing)
Storage -10°C to 50°C or 14°F to 122°F
and 90%RH (non-condensing)

EN 5
digital alarm clock with room climate control BZ01
Scope of delivery
• 1x Device BZ01
• 1x Battery, typeAAA, 1.5V
• 1 x Quick guide
Transport and storage
Note
If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.
Transport
When transporting the device, ensure dry conditions and and
protect the device from external influences e.g. by using a
suitable bag.
Storage
When the device is not being used, observe the following
storage conditions:
• dry and protected from frost and heat
• protected from dust and direct sunlight
• the storage temperature complies with the values specified
in the Technical data
• Remove the battery from the device.
Operation
Inserting the battery
Prior to first use, insert a battery (typeAAA, 1.5V) into the
device. To do so, please proceed as follows:
1. Open the battery compartment(12) at the rear of the
device.
2. Insert the battery with correct polarity(+/-).
12
3. Close the battery compartment.
ðThe display will be activated and an acoustic signal is
emitted.
Switching between the indication of time, alarm time and
calendar year
By pressing the MODEbutton(7) you can switch the
indication(5) from the time(time mode) to the alarm time(alarm
mode) and then to the indication of the calendar year(date
mode) by pressing the MODEbutton(7) once more.
14
15
16
No. Designation
14 Time mode
15 Alarm mode
16 Date mode
Setting the time and time format
Please proceed as follows to set the time and the time format:
üYou have selected the time mode(14).
1. Press the SETbutton(8) for approx. 3seconds.
ðThe time format(12hr/ 24hr) flashes on the display.
2. Use the UPbutton(9) to set the desired time format.
3. Once the time format has been set correctly, press the
SETbutton(8) once more to switch to the hour display.
ðThe hour display starts flashing.
4. Use the UPbutton(9) to adjust the hourdisplay correctly.
Keep the button pressed to adjust the value at a faster
pace.
5. Once the hourdisplay has been set correctly, press the
SETbutton(8) once more to switch to the minute display.
ðThe minute display starts flashing.
6. Use the UPbutton(9) to adjust the minute display
correctly. Keep the button pressed to adjust the value at a
faster pace.
7. Once the minute display has been set correctly, press the
MODEbutton(7) to exit the mode.

6 EN
digital alarm clock with room climate control BZ01
Setting the alarm time
Please proceed as follows to set the alarm time:
1. Switch over into the alarm mode(7) by pressing the
MODEbutton(15).
ðThe indication(5) switches over into alarm mode and
displays AL, the indication(4) displays the alarm time.
2. Press the SETbutton(8) for approx. 3seconds.
ðThe hour display starts flashing.
3. Use the UPbutton(9) to adjust the hourdisplay correctly.
Keep the button pressed to adjust the value at a faster
pace.
4. Once the hourdisplay has been set correctly, press the
SETbutton(8) once more to switch to the minute display.
ðThe minute display starts flashing.
5. Use the UPbutton(9) to adjust the minute display
correctly. Keep the button pressed to adjust the value at a
faster pace.
6. Once the minute display has been set correctly, press the
MODEbutton(7) to exit the mode.
Setting the date and weekday
Please proceed as follows to set the date and the weekday:
1. Switch over into the date mode(7) by pressing the
MODEbutton(16).
ðThe indication(5) displays the month and day, the
indication(5) displays the calendar year and the
indication(4) displays the weekday.
2. Press the SETbutton(8) for approx. 3seconds.
ðThe calendar year flashes on the display.
3. Use the UPbutton(9) to adjust the displayed calendar year
correctly. Keep the button pressed to adjust the value at a
faster pace.
4. Once the displayed calendar year has been set correctly,
press the SETbutton(8) once more to switch to the month
display.
ðThe month display(M) starts flashing.
5. Use the UPbutton(9) to adjust the month display correctly.
Keep the button pressed to adjust the value at a faster
pace.
6. Once the month display has been set correctly, press the
SETbutton(8) once more to switch to the day display.
ðThe daydisplay(D) starts flashing.
7. Use the UPbutton(9) to adjust the daydisplay correctly.
Keep the button pressed to adjust the value at a faster
pace.
ðThe weekday will automatically be set to the correct
day.
8. Once the daydisplay has been set correctly, press the
MODEbutton(7) to exit the mode.
De-/activating the alarm function and the hourly time signal
1. Switch over into the alarm mode(15) by pressing the
MODEbutton(7).
ðThe indication(4) switches over into alarm mode and
displays AL, the indication(5) displays the alarm time.
2. Press the UPbutton(9) to activate the alarm function.
ðThe alarm icon(17) will be indicated on the display.
3. By pressing the UPbutton(9) once more you can now in
turn select the following functions:
• Hourly time signal activated instead of the alarm function.
The icon for the hourly alarm signal(18) will be displayed
and an acoustic signal is emitted every full hour.
• Both the alarm function and the hourly time signal are
activated. Both icons(17/18) will be displayed.
• Both the alarm function and the hourly time signal are
deactivated. None of the two icons will be displayed.
17
18
19 Zz
No. Designation
17 Alarm function activated icon
18 Hourly time signal activated icon
19 Snooze function activated icon
Turning off the alarm
When the acoustic alarm signal is emitted, you can turn it off by
pressing any of the buttons (other than SNZ(10)).
Note:
The alarm will stop automatically after 1minute if no button is
pressed.

EN 7
digital alarm clock with room climate control BZ01
Snooze function
The device comes equipped with a snooze function enabling you
to turn the alarm off for the time being. The acoustic alarm
signal will be emitted once more after approx. 4minutes:
1. Press the SNZbutton(10) when you hear the alarm.
ðThe alarm will stop and the icon for the snooze
function(19) starts flashing.
2. After approx. 4minutes, when the acoustic alarm signal is
emitted once more, you can use the snooze function again
by pressingSNZ(10).
3. To deactivate the active snooze function, simply press any
other button thanSNZ(10).
ðThe icon for the snooze function(19) will stop flashing
and the snooze function is deactivated.
Weather forecast
The device has an indication for the weather forecast(1)
displayed by foursymbols:
20 21
22 23
No. Designation
20 Sunny symbol
21 Partly cloudy symbol
22 Overcast symbol
23 Rain symbol
Info
The device is not fitted with a sensor for atmospheric
pressure. The weather forecast is based on the
changing relative humidity level. If the relative humidity
level changes by more than ±5% within one hour, the
indication will be adjusted accordingly.
Indication of minimum and maximum values
The device saves the minimum and maximum values for
temperature and relative humidity. These values can be
displayed by pressing the UPbutton(9):
Info
The minimum and maximum values can only be
indicated when the device is in time mode.
1. Briefly press the UPbutton(9) once to display the
maximum values.
ðThe maximum values will be displayed along with the
MAXsymbol.
2. Press the UPbutton(9) again to display the minimum
values.
ðThe minimum values will be displayed along with the
MINsymbol.
3. Press the UPbutton(9) once more to exit the mode.
Switching the temperature indication between°C and°F
Briefly press the SETbutton(8) to switch the indicated
temperature unit from degrees Celsius to degrees Fahrenheit or
vice versa.
Info
Switching between °C and °F can only be
accomplished in the time mode.
Resetting the system
You can reset the system to its initial configuration. To do so,
use a pointed object to press the RESETbutton in the
opening(11).
Reset the system if one of the following situations occurs:
• The battery was changed.
• If the indication in the display is no longer visible.
• If you use the buttons and the device does not respond to
their operation.

8 EN
digital alarm clock with room climate control BZ01
Maintenance and repair
Battery change
A battery change is required when the display is no longer or
only partly visible.
See chapter Operation.
Cleaning
Clean the device with a soft, damp and lint-free cloth. Make
sure that no moisture enters the housing. Do not use any
sprays, solvents, alcohol-based cleaning agents or abrasive
cleaners, but only clean water to moisten the cloth.
Repair
Do not modify the device or install any spare parts. For repairs
or device testing, contact the manufacturer.
Disposal
The icon with the crossed-out waste bin on waste
electrical or electronic equipment stipulates that this equipment
must not be disposed of with the household waste at the end of
its life. You will find collection points for free return of waste
electrical and electronic equipment in your vicinity. The
addresses can be obtained from your municipality or local
administration. You can also find out about other return options
that apply for many EU countries on the website
https://hub.trotec.com/?id=45090. Otherwise, please contact an
official recycling centre for electronic and electrical equipment
authorised for your country.
The separate collection of waste electrical and electronic
equipment aims to enable the re-use, recycling and other forms
of recovery of waste equipment as well as to prevent negative
effects for the environment and human health caused by the
disposal of hazardous substances potentially contained in the
equipment.
In the European Union, batteries and accumulators must not be
treated as domestic waste, but must be disposed of
professionally in accordance with Directive 2006/66/EC of the
European Parliament and of the Council of 6September 2006
on batteries and accumulators. Please dispose of batteries and
accumulators according to the relevant legal requirements.

Trotec GmbH
Grebbener Str. 7
D-52525 Heinsberg
[phone]
[phone]
[email protected]
www.trotec.com