Trotec HYSTREAM 3400 User manual

OPERATING MANUAL
HOT AIR BLOWER
HYSTREAM3400
EN
TRT-BA-HYSTREAM3400-HS-002-EN

Operating manual – Hot air blower HYSTREAM 3400 ENB – 1
Table of contents
Notes regarding the operating manual ..............B - 1
Safety...............................................................B - 1
Operation..........................................................B - 3
Transport ..........................................................B - 4
Errors and faults ...............................................B - 4
Maintenance.....................................................B - 4
Repair...............................................................B - 5
Technical data .................................................B - 5
Disposal............................................................B - 6
Optional accessories ........................................B - 5
Notes regarding the operating manual
Symbols
cHazardous electric voltage!
Warns about a hazard from electrical voltage
which can lead to injuries or even death.
Hazard from hot surfaces!
Warns of a hazard resulting from hot surfaces
which can lead to injuries.
mDanger!
Warns of a hazard which can lead to injuries.
mCaution!
Warns of a hazard which can lead to property
damage.
The current version of the operating manual can be found
at:
www.trotec.de
http://hub.trotec.com/?id=26899
Legal notice
This release replaces all previous versions. No part of this
publication may be reproduced without written permission
from Trotec. The same applies for electronically processing,
duplicating or spreading the publication. Subject to techni-
cal changes. All rights reserved. Trademarks are used with-
out guarantee that they may be used freely and primarily
following the spelling of the manufacturer. Product names
are registered.
Changes to construction in the interests of constant im-
provements to the product, as well as changes to the shape
and colour are reserved. The scope of delivery may vary
from product images. This document was created with all
due care. Trotec accepts no liability whatsoever for possible
mistakes or omissions. © Trotec
Safety
Carefully read the operating manual before using the
device and keep it within reach!
mDanger!
The device becomes very hot! Improper use
of the hot air blower can result in injuries
due to burns and in an imminent fire hazard!
•Do not use the device in rooms exposed to explosion
hazards where fuel, solvents, varnishes or other easily
inflammable vapours are stored nor in atmospheres con-
taining oil, sulphur, chlorine or salt.
•Do not use the device in humid, wet or muddy surround-
ings.
•Ensure a minimum distance of 50 cm to combustible
substances. Do not use the device in immediate prox-
imity to curtains.
•Do not use the device on combustible ground or near
inflammable objects.
• Make sure that air inlet and nozzle are not obstructed.
•Only connect the device to the mains if voltage and fre-
quency correspond to the values given on the nameplate.
•Keep a sufficient distance to animals, especially small
animals, e.g. aviaries.

Operating manual – Hot air blower HYSTREAM 3400
EN B – 2
• Keep away children. People who use this device must
be aware of the dangers that occur when working with
a hot air blower.
• Never reach or put objects into the device.
• Never cover the device during operation, for it becomes
very hot!
• Never point the activated device at people, animals,
plants or combustible objects or liquids.
• Never leave the activated device unattended.
• Ensure that all electric cables outside of the device are
protected from damage (e.g. caused by animals).
• Observe the device's power input, cable length and in-
tended use when selecting extensions to the connecting
cable. Avoid electrical overload. Extension cables must
always be reeled off completely.
• Pull the plug from the socket if the device is not in use for
extended periods of time.
• Allow the device to cool down completely before trans-
porting it.
Intended use
The device was developed for the purpose of generating hot
air and may only be used whilst adhering to the technical
data.
The hot air blower HyStream 3400 was designed for the
following fields of application:
• for hot air applications combined with a tile lifting sys-
tem such as the TilexPro from Trotec
• to remove flooring
• to shrink foils and shrinking hoses
• to dry incombustible paints and varnishes, damp objects
or grounds
• to remove incombustible paints and varnishes
• to bend and heat-seal plastics
• for sealing work e.g. roofs, plastic foil, tents, tarpaulin
and the like
• for melting and thawing incombustible parts
Every application going beyond these terms of use is pro-
hibited!
Improper use
Only use the device as intended, never in the immediate
vicinity of combustible objects and not to set fire.
Residual risks
Hazard from hot surfaces!
Parts of the device, especially at the noz-
zle, become very hot during operation.
There is a danger of burning and fire.
m
Danger!
Parts of this appliance can become very
hot and cause burns. Particular attention
is to be paid when there are children or
vulnerable persons present!
mDanger!
Improper handling entails a risk of burn-
ing. Only use the device as intended!
mDanger!
The device must not be covered, there is
an imminent fire hazard!
c
Hazardous electric voltage!
Work on the electrical components must
only be carried out by an authorised spe-
cialist company!
Behaviour in the event of an emergency
1. In case of an emergency, immediately switch the device
off using the ON/OFF switch.
2. Remove the mains plug from the mains socket.
Do not reconnect a defective device to the mains.

Operating manual – Hot air blower HYSTREAM 3400 ENB – 3
No. Designation
(1) Nozzle
(2) Venting slots
(3) temperature setting +/- °C [1-9]
(4) ON/OFF switch [0/1]
Operation
•The device was designed for many application areas,
plan yours carefully and prepare a corresponding work
space with sufficient distance to combustible materials.
•The device must be connected to a properly secured
mains power socket.
Start-up
1. Set the device via the temperature setting(3) to the low-
est level[1].
2. Then use the ON/OFF switch(4) to switch the device on.
3. Select the desired temperature range via the tempera-
ture setting(3): the temperature can be steplessly ad-
justed between 20°C and 650°C.
4. Only hold the device in one hand or place it on the work-
ing surface. Make sure that the hot air blower cannot be
pulled down by the power cable.
5. Always start out at a low temperature and then slowly
adjust it to your operating range.
1
22
3
4
Application of the HyStream3400 with TilexPro30
tile lifting system

Operating manual – Hot air blower HYSTREAM 3400
EN B – 4
6. Further information regarding the use of the HyS-
tream3400 with tile lifting system TilexPro30 or Tilex-
Pro 50 can be gathered from the operating manual of
the TilexPro.
7. This professional tool is equipped with a highly efficient
ceramic heating element. Handle the device carefully.
Do not drop it. Always put it safely aside after use.
Switching the device off
1. Turn the temperature setting(3) to minimum[1]. Allow
the device to cool down in the air flow.
2. Then use the ON/OFF switch to switch the device off.
Wait for the end of the brief rundown period, then pull
the mains plug from the socket.
3. Before performing any further activities, e.g. storage or
transport, wait until the device has cooled down com-
pletely.
Transport
Before transporting the device, proceed as follows:
• Switch the device off.
• Remove the mains plug from the mains socket.
Do not use the power cable to drag the device!
• Wait until the device has cooled down completely.
Errors and faults
The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.
c
m
Troubleshooting tasks which require the
housing to be opened must only be carried
out by a specialist dealer or by Trotec.
Slight smoke or odour are emitted during first use:
•This is not a fault. These phenomena disappear after a
brief runtime.
The device does not start:
• Check the power connection (230 V/1~/50 Hz).
• Check the mains plug for damages.
• Have an electrical inspection carried out by Trotec.
The device supplies cold air only:
• The ceramic heating element or the temperature control
might be damaged.
• Please contact the Trotec customer service.
Your device still does not operate correctly after these
checks?
•In case of unusual sounds, sparking or motor problems,
switch the device off and put it down carefully.
• Please contact the Trotec customer service.
Maintenance
Activities required before starting maintenance:
• Do not touch the mains plug with wet or damp hands.
•Allow the device to cool down completely before per-
forming any maintenance work!
•Always remove the mains plug before any maintenance
work!
c
m
Maintenance tasks which require the
housing to be opened must only be carried
out upon consultation with Trotec.
Cleaning the housing:
Hazard from hot surfaces!
Burn hazard! Allow the device to cool down
completely before cleaning the housing!
Clean the device with a soft, damp and lint-free cloth. Make
sure that no moisture enters the housing. Do not use sprays,
solvents, harsh or abrasive cleaners to dampen the cloth.

Operating manual – Hot air blower HYSTREAM 3400 ENB – 5
Repair
Replacing the ceramic heating element
(qualified persons only)
• Remove the mains plug from the mains socket.
• Put the cooled-off device on a working surface.
•Use a Phillips screwdriver to loosen the nozzle's
4screws(1), then carefully pull it off towards the front.
•Carefully hold the ceramic element directly by the white
rim and remove it from the plug connection by pulling
and shaking it gently.
•Observe the fits before inserting the new heating ele-
ment: the notches and cut-outs must be compatible.
•Push the new heating element firmly into the plug con-
nection until the whit rim is seated flush within the de-
vice.
• Fasten the nozzle back in place.
•Switch the device back on – starting at the lowest tem-
perature level.
Technical data
Nominal capacity 3400W
Mains connection
with protective insulation
1/N ~ 230V
yes
Power frequency 50Hz
Shaped plug CEE 7/17
Cable length 2.90 m
Air temperature 20°C – 650°C
Air flow rate 320 l/min
Air pressure 3000 Pa
Noise level 65 dB (A)
Optional accessories
TilexPro system 30
for tile formats sized up to
30cm
art. no. 6.100.000.050
TilexPro system 50
for tile formats sized up to
50cm
art. no. 6.100.000.052

Disposal
Always dispose of packing materials in an
environmentally friendly manner and in
accordance with the applicable local
disposal regulations.
The icon with the crossed-out waste bin on waste
electrical or electronic equipment is taken from Directive
2012/19/EU. It states that this device must not be disposed
of with the household waste at the end of its life. You will
find collection points for free return of waste electrical and
electronic equipment in your vicinity. The addresses can be
obtained from your municipality or local administration. You
can also find out about other return options that apply for
many EU countries on the website
https://hub.trotec.com/?id=45090.
Otherwise, please contact an official recycling centre for
electronic and electrical equipment authorised for your
country. The separate collection of waste electrical and
electronic equipment aims to enable the re-use, recycling
and other forms of recovery of waste equipment as well as
to prevent negative effects for the environment and human
health caused by the disposal of hazardous substances
potentially contained in the equipment.
Only for United Kingdom
According to Waste Electrical and Electronic Equipment
Regulations 2013 (SI 2013/3113) (as amended) devices
that are no longer usable must be collected separately and
disposed of in an environmentally friendly manner.
Operating manual – Hot air blower HYSTREAM 3400
EN B – 6

Trotec GmbH
Grebbener Str. 7
D-52525 Heinsberg
[phone]
[phone]
[e-mail]
www.trotec.com