Trotec PPWS 10-20V User manual

TRT-BA-PPWS 10-20V-TC220405TTRT01-001-EN
PPWS 10-20V
EN
ORIGINAL INSTRUCTIONS
CORDLESS HIGH-PRESSURE
CLEANER

2 EN
cordless high-pressure cleaner PPWS 10-20V
Table of contents
Notes regarding the instructions ..........................................2
Safety .....................................................................................2
Information about the device................................................6
Transport and storage...........................................................7
Start-up..................................................................................8
Operation .............................................................................11
Available accessories..........................................................12
Errors and faults..................................................................12
Maintenance ........................................................................13
Disposal ...............................................................................13
Declaration of conformity ...................................................14
Notes regarding the instructions
Symbols
Warning of electrical voltage
This symbol indicates dangers to the life and health of
persons due to electrical voltage.
Warning of explosive substances
This symbol indicates dangers to the life and health of
persons due to potentially explosive substances.
Warning
This signal word indicates a hazard with an average
risk level which, if not avoided, can result in serious
injury or death.
Caution
This signal word indicates a hazard with a low risk
level which, if not avoided, can result in minor or
moderate injury.
Note
This signal word indicates important information (e.g.
material damage), but does not indicate hazards.
Info
Information marked with this symbol helps you to carry
out your tasks quickly and safely.
Follow the manual
Information marked with this symbol indicates that the
instructions must be observed.
Wear hearing protection
Information marked with this symbol indicates that you
should wear hearing protection.
Wear safety glasses
Information marked with this symbol indicates that you
should wear eye protection.
You can download the current version of the instructions via the
following link:
PPWS 10-20V
https://hub.trotec.com/?id=46508
Safety
Warning
Read all safety warnings, instructions, illustrations
and specifications provided with this power tool.
Failure to follow all instructions listed below may result
in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
General safety instructions
• The device must not be used by children. Children should
be supervised to ensure that they do not play with the
appliance.
• The device can be used by persons with reduced physical,
sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way
and understand the hazards involved.
• Persons who are not familiar with the instructions must not
use this device.
• Persons who have not been instructed must not operate
the high-pressure cleaner.
• Switch off the device immediately when you detect a fault
or defect during operation and remove the battery. Read
the information regarding potential faults or contact our
service centre.

EN 3
cordless high-pressure cleaner PPWS 10-20V
General Battery Pack / Charger Safety Warnings
•This charger can be used by children aged
from8years and above and persons with reduced
physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given
supervision or instruction concerning use of the
appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by
children without supervision.
•Never insert non-rechargeable batteries into the
charger. A charger that is suitable for one type of battery
pack may create a risk of fire and explosion, when used
with another battery pack or non-rechargeable batteries.
• Only charge the Li-Ion battery "Multiflex20– 2.0DC"
(capacity of 2.0 Ah= 5 battery cells) with the charger
"Multiflex 20– 2.0 AC". The battery voltage must match
the battery charging voltage of the charger.
•Use products only with the specifically designated
battery packs. Use of any other battery packs may create
a risk of injury and fire.
•When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys, nails,
screws or other small metal objects, that can make a
connection from one terminal to another. Shorting the
battery terminals together may cause burns or a fire.
•Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with
another battery pack.
•Do not charge other battery packs. The charger is only
suitable for use with the supplied battery pack and with
the voltages specified in the technical data. Otherwise,
there is a risk of fire and explosion.
•Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally occurs,
flush with water. If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery may cause
irritation or burns.
•In case of damage and improper use of the battery,
vapours may be emitted. Provide for fresh air and seek
medical help in case of complaints. The vapours can
irritate the respiratory system.
•Do not open the battery. There is danger of a short
circuit.
•Do not short-circuit the battery. There is danger of
explosion.
•Batteries must not be exposed to mechanical impacts.
•Protect electrical parts against moisture. To prevent an
electric shock, never immerse them in water or other
liquids during cleaning or operation. Never hold the
charger under running water. Please observe the
instructions for cleaning and maintenance.
•The charger is only suited for indoor use.
•Keep the charger clean. Contamination entails a risk of
electric shock.
•Do not operate the charger on highly combustible
ground (e.g. paper, textiles etc.) or in an inflammable
environment. The heat generated by the charger during
charging entails a risk of fire.
•Only use the charger for charging the battery. The
charger must not be used as power supply for the power
tool.
Safety instructions regarding the operation of this
device
• Using this device improperly can be dangerous. Never
direct the jet to persons, animals, electrical parts or the
device itself.
• For window cleaning only use the soft jet, otherwise you
can damage the window.
• The use of salt water causes corrosion on the device.
• Do not use the high-pressure cleaner on yourself or other
persons to clean clothes or shoes.
• Wear suitable protective clothing and goggles for
protection against water or dirt spraying back.
• Make sure that other persons near the device are also
wearing protective clothing.
• Keep children away from the running device.
• Do not use this device near highly flammable fluids or
gases. There is a risk of fire or explosion.
• Spraying flammable fluids is not permitted. There is a
danger of explosion.
• If you come into contact with the detergent, rinse with
plenty of water. There is a risk of acid burns!
• When using the suction hose, be sure to position it so that
you will not trip over it. When using the suction hose, make
sure that the device does not run dry.
• Make sure that the suction hose is not squashed or kinked.
The device may be damaged by this and you may be
injured.
• Store the device in a dry place and ensure that it is outside
the reach of children.

4 EN
cordless high-pressure cleaner PPWS 10-20V
• Only use the device when it is in perfect condition. Before
you start working, check whether it is damaged,
incomplete or whether it has been converted. A specialist
should check the device before it is started up, ensuring
that the electrical protective measures required are
provided for.
• Check important parts such as the suction hose, the
nozzles or the spray lance.
• Protect the device against frost and against running dry.
• High-pressure hoses, fittings and couplings are important
for the device's safety. High-pressure hoses, fittings and
couplings recommended by the manufacturer are the only
ones permissible.
• Only original spare parts from the manufacturer or spare
parts approved by the manufacturer may be used.
• An authorised electrically skilled person is the only person
allowed to open the device. If the device needs to be
repaired, always contact our service centre.
• Do not use any accessories that have not been
recommended by Trotec. The use of non-recommended
accessories may cause an electric shock or fire.
• It is important to check the device for damage every time
before it is used.
• Wear sturdy shoes for protection against an electric shock.
Intended use
Only use the device PPWS 10-20V:
• for cleaning surfaces and objects outdoors
• for watering
• for the use with neutral, biodegradable detergents
Make sure that you always operate this device with a sufficient
amount of water.
We recommend using the power tool with original Trotec
accessories.
Foreseeable misuse
Do not use the device to hose down persons or animals.
Do not use the device with salt water.
Any other use than the one described in the chapter "Intended
use" is regarded as reasonably foreseeable misuse.
Personnel qualifications
People who use this device must:
• have read and understood the instructions, especially the
Safety chapter.
Safety signs and labels on the battery and the charger
Note
Do not remove any safety signs, stickers or labels from
the device. Keep all safety signs, stickers and labels in
legible condition.
The following safety signs and labels are attached to the
battery:
Warning of explosion risk!
These symbols indicate the following:
Do not expose the battery pack or tool to fire or
excessive temperature! Do not let the battery come into
contact with water or fire! Avoid direct sunlight and
moisture. There is a risk of explosion!
Never charge the battery at ambient temperatures
below10°C or above40°C. Charging improperly or at
temperatures outsides the specified range may damage
the battery and increase the risk of fire.
Observe the correct disposal of the battery!
This symbol indicates the following:
Ensure that the battery is disposed of correctly and
never dispose of it in waste water or public waters.
The battery contains irritating, caustic and toxic
substances that pose significant risks to people and the
environment.
The following safety signs and labels are attached to the
charger:
This symbol indicates the following:
Read the instructions or operating manual before
charging the battery.
This symbol indicates the following:
Only use the charger for charging the battery in dry
interior spaces. Do not charge the device outdoors.
Safety signs and labels attached
Note
Do not remove any safety signs, stickers or labels from
the device. Keep all safety signs, stickers and labels in
legible condition.
The following safety signs and labels are attached to the device:
92
Guaranteed sound power level of the device.
The device is not suitable for connection to a drinking
water supply system.

EN 5
cordless high-pressure cleaner PPWS 10-20V
Personal protective equipment
Wear eye protection.
With it you protect your eyes from splintering, falling
and flying pieces which could cause injuries.
Wear protective gloves.
They protect your hands from burns, crushing injuries
and skin abrasions.
Residual risks
Warning of electrical voltage
Work on the electrical components must only be
carried out by an authorised specialist company!
Warning of electrical voltage
There is a risk of a short-circuit due to liquids
penetrating the housing!
Do not immerse the device and the accessories in
water. Make sure that no water or other liquids can
enter the housing.
Warning of explosive substances
Do not expose the battery to temperatures above
45°C! Do not let the battery come into contact with
water or fire! Avoid direct sunlight and moisture. There
is a risk of explosion!
Warning
Risk of injuries caused by parts flung out
uncontrollably. Never use the device if children, other
people or pets are nearby! Also make sure to keep
enough distance to your hands and feet.
Warning
Do not work outdoors with the device in case of
approaching rain or thunderstorms. The device may
attract a lightning strike. Water ingress into the
housing can cause an electric shock.
Warning
Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way!
Observe the personnel qualifications!
Warning
The device is not a toy and does not belong in the
hands of children.
Warning
Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
Caution
Vibration emissions can cause a health hazard if the
device is used for an extended period of time or if it is
not properly handled and maintained.
Caution
Keep a sufficient distance from heat sources.
Note
If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.
Behaviour in the event of an emergency/ emergency
stop function
Emergency stop:
Removing the battery results in the function of the device
stopping immediately. Leave the battery out in order to secure
the device against accidental switch-on.
Behaviour in the event of an emergency:
1. Switch the device off.
2. In the event of an emergency, remove the battery from the
device: Hold the release button of the battery and pull the
battery off the device as described in chapter "Removing
the battery".
3. Do not insert the battery if the device is defective.

6 EN
cordless high-pressure cleaner PPWS 10-20V
Information about the device
Device description
The device PPWS 10-20V cleans surfaces and objects outdoors
and can be used for watering.
Thanks to its self-priming function, you can even use the device
independently of water pipes and, for example, utilise water
from a rain barrel.
If required, the device can also be operated using detergents. If
you do so, use the spray attachment.
It comes equipped with a multi-function nozzle with 6 different
settings for various applications.
Furthermore, the device has a start lock to prevent it from being
switched on unintentionally.
The battery comes with its own battery level indication. As a
result you can check the current charging status without having
to connect it to the device.
Device depiction
1
2
4
15
3
10
14
13
11
9
5
12
6
7
8
18
16
17
No. Designation
1Start lock
2On/off switch
3Battery holder
4Hose connector
5Spray attachment with detergent container
6Quick charger
7Red battery LED (battery charging)
8Green battery LED (quick charger ready for operation)
9Carrying net
10 Multi-function nozzle
11 Spray lance
12 Float
13 Filter
14 Hose with quick coupling
15 Spray lance/spray attachment holder
16 Release button
17 Battery level indication
18 Battery
Scope of delivery
• 1 x Cordless high-pressure cleaner PPWS 10-20V
• 1 x Rechargeable battery
• 1x Quick charger
• 1 x Hose
• 1 x Filter
• 1 x Spray attachment
• 1 x Multi-function nozzle
• 1 x Spray lance
• 1 x Detergent container
• 1 x Carrying net
• 1x manual

EN 7
cordless high-pressure cleaner PPWS 10-20V
Technical data
Parameter Value
Model PPWS 10-20V
Nominal voltage 20V
Max. pressure 22bar
Flow rate 120l/h
Inlet water pressure 0.5Mpa
Max. water temperature 65 °C
Suction height
- optimum
- max.
1.5m
4.0m
Spraying range 7 m
Weight 1kg
Battery Multiflex20 – 2.0 DC
Type Li-ion
Nominal voltage 20V
Nominal capacity 2.0Ah
Rechargeable cells 5cells
Capacity 40Wh
Quick charger Multiflex20 – 2.0 AC
Input
Nominal voltage 230 – 240 V / 50 Hz
Power input 65W
Output
Nominal voltage 21.5V
Charging current 2.4A
Fusing 3.15A (slow-blowing)
Charging time 1 h
Cable length 1.5 m
Protection class II (double insulation) /
Vibration information according to EN60335-2-54
Total vibration emission
value ah
Uncertainty K
2.5 m/s²
1.5 m/s²
Sound values according to EN60335-2-54
Sound pressure level LPA 83.7 dB(A)
Sound power LWA 89.0 dB(A)
Uncertainty K 3 dB
Wear hearing protection.
Excessive noise can lead to hearing loss.
Transport and storage
Note
If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.
Transport
Before transporting the device, observe the following:
• Hold onto the mains plug while pulling the power cable of
the charger out of the mains socket.
• Allow the device to cool down.
• Remove the battery from the device.
The supplied Li-ion batteries are subjects to the requirements of
dangerous goods legislation.
Observe the following when transporting or shipping Li-ion
batteries:
• The user may transport the batteries by road without any
additional requirements.
• If transport is carried out by third parties (e.g. air transport
or forwarding company), special requirements as to
packaging and labelling must be observed. This includes
consulting a dangerous goods specialist when preparing
the package.
– Only ship batteries if their housing is undamaged.
– Mask open terminals with tape and pack the battery in
a way that it cannot move inside the packaging.
– Please also observe any other national regulations.
Storage
Before storing the device, observe the following:
• Hold onto the mains plug while pulling the power cable of
the charger out of the mains socket.
• Allow the device to cool down.
• Remove the battery from the device.
• Drain the water completely from the device. Disconnect
the connections to the water supply. Then switch the
device on for some seconds until the water ceases to exit
the spray lance. Switch the device off.
• Store the spray lance in a standing position, the connection
side pointing downwards.
• Completely empty the hose with filter.
• If there are any residues of water on the device and
accessories, damage can be cause by frost.
• Store the device and its accessories in a frost-free
environment.
• Clean the device as described in the Maintenance chapter.

8 EN
cordless high-pressure cleaner PPWS 10-20V
• Do not store Li-ion batteries which are completely
discharged. Storing discharged batteries can lead to a
deep discharge and thus damage the battery.
When the device is not being used, observe the following
storage conditions:
• dry and protected from frost and heat
• Ambient temperature below 45°C
• Protected from dust and direct sunlight
Start-up
Unpacking the device
• Take the device and the accessories out of the packaging.
• Check the contents for completeness and look for
damages.
Warning
Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
• Dispose of the packaging material according to the
national regulations.
Charging the battery
Note
The battery can be damaged in case of improper
charging.
Remove the charger's mains plug before inserting or
removing the battery.
Never charge the battery at ambient temperatures
below 10°C or above 45°C.
The battery is partially charged upon delivery to avoid damage
to the battery caused by a deep discharge.
Prior to initial start-up and when the battery is low (only the red
LED in the battery level indication(17) is illuminated), the
battery should be charged. To do so, please proceed as follows:
1. Slide the battery(18) onto the quick charger(6) as
depicted until the battery locks in place.
1 h
18
6
8
7
17
2. Insert the mains plug of the quick charger(6) into a
properly fused mains socket.
ðThe red battery LED(7) lights up.
ðCharging requires approx. one hour.
3. Wait until the red battery LED(7) goes off and the green
battery LED(8) lights up.
ðThe battery(18) is fully charged.
4. Hold onto the mains plug while pulling the power cable of
the quick charger(6) out of the mains socket.
ðThe battery(18) and the quick charger(6) may have
become warm during charging.
Allow the battery(18) to cool down to room
temperature.
5. Take the battery(18) out of the quick charger(6) by
pressing and holding the release button(16) and pulling
the battery(18) off the quick charger(6).
Inserting the battery
1. Slide the battery(18) into the holder(3) until it locks in
place.
18

EN 9
cordless high-pressure cleaner PPWS 10-20V
Removing the battery
1. Detach the battery(18) from the device by pressing and
holding the unlocking button(16, I.) and pulling the battery
off the device(II.).
16
18
2. If required, charge the battery(18) as described in the
section Charging the battery.
Checking the battery charging status
The battery comes with an integrated battery level indication.
The battery status is displayed as follows by the three LEDs of
the battery level indication(17):
LED colour Meaning
Green – Orange – Red maximum charge/ power
Orange – Red medium charge/ power
Red weak charge – recharge the
battery
1. Press on the battery icon(19) on the battery(18).
ðYou can read the battery status from the battery level
indication(17).
19
17
Suction of water from containers
Info
The device is provided with an integrated water suction
function. This function is only permissible using the
suction hose(14) and filter(13).
Warning
Do not suck in any water from natural sources.
Contamination by backflowing detergents may occur.
Note
Dry running causes damage to the device.
1. Connect the quick coupling(20) of the hose(14) to the
hose connection(4) on the device.
2. Plunge the end with the filter(13) into the water source
(e.g a rain barrel). Make sure that a sufficient amount of
water is available.
3. The hose(14) comes equipped with a float(12). It always
holds the filter(13) slightly beneath the water surface,
almost completely preventing dirty water from being
sucked in.
4. It is important that there is no air in the hose(14). Plunge
the hose(14) with the filter(13) completely into the water
source (e.g. a rain barrel) to vent the former.
14
13
20

10 EN
cordless high-pressure cleaner PPWS 10-20V
Connection with garden hose to water inlet (optional)
According to valid regulations, the high-pressure cleaner must
not be connected to the drinking water network without a
system separator. Use a suitable system separator in
compliance with EN 12729 type BA.
If the water used flows through a system separator, it is no
longer drinkable. You can purchase a system separator in the
specialist trade.
A system separator prevents water and detergent from flowing
back into the drinking water pipeline.
• Use a commercially available garden hose for the water
inlet and make sure it is long enough.
• Use the device on a domestic water connection with a
maximum pressure of 5bar.
1. Remove the quick coupling(20) from the water hose.
2. Connect the garden hose to the water supply.
3. To vent the garden hose, open the tap and let the water
flow until it comes out at the other end without producing
any bubbles.
4. Stop the water flow.
5. Connect the quick coupling(20) to the garden hose again.
6. Connect the garden hose(14) to the hose connection(4) on
the device.
4
Info
If you have connected a different quick coupling with
water stop function to your water supply, remove the
quick coupling before venting. Vent without the quick
coupling and reconnect it again afterwards.
Installing the multi-function nozzle/spray attachment
1. Insert the spray lance(11) with the multi-function
nozzle(10) into the device first and turn it until it reaches
the lock (bayonet catch). The spray attachment with the
detergent container(5) is installed in the same way.
10
11
2. Disassembly is carried out in reversed order.
10
11

EN 11
cordless high-pressure cleaner PPWS 10-20V
Operation
Warning
Do not work outdoors with the device in case of
approaching rain or thunderstorms. The device may
attract a lightning strike. Water ingress into the
housing can cause an electric shock.
Warning
Risk of injuries caused by parts flung out
uncontrollably. Never use the device if children, other
people or pets are nearby! Also make sure to keep
enough distance to your hands and feet.
Tips and notes on handling the high-pressure cleaner
General information:
• Always hold the handle and spray lance tight with both
hands. There is the danger of a kickback.
• The different types of jets that can be selected are
provided for cleaning surfaces and objects.
• The soft jet is intended for watering and washing after the
use of detergents and for sensitive surfaces (e.g. car
paint).
• Keep your distance to other persons.
Switching the device on and off
1. Check whether the water supply is connected and the
connection is tight.
2. Press the start lock(1) to be able to actuate the on/off
switch(2).
2
1
3. Press the on/off switch(2) and hold it during operation.
4. After completion of the work, let go of the on/off switch(2)
to stop the device.
Adjusting the spray jet
1. You can select 6 different settings on the multi-function
nozzle(10).
2. The following symbols are shown on the multi-function
nozzle(10). Turn the multi-function nozzle(10) to the
desired setting. The white arrow on the top side indicates
the setting selected.
Settings
0°/15°/25°/40° spraying
angle
Jet sprays upwards
Soft jet for watering/
washing
Using detergents
Use the spray attachment with a neutral, biodegradable
detergent. Always use detergents sparingly in terms of
environmental protection.

12 EN
cordless high-pressure cleaner PPWS 10-20V
Shutdown
Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.
• Switch the device off.
• If required, allow the device to cool down.
• Hold onto the mains plug while pulling the power cable of
the charger out of the mains socket.
• Remove the battery from the device (see Start-up chapter).
• Remove the lance from the device.
• Clean the device according to the Maintenance chapter.
• Store the device according to the Transport and storage
chapter.
Available accessories
Warning
Only use accessories and additional equipment
specified in the instructions.
Using insertion tools or accessories other than those
specified in the instructions may cause a risk of injury.
Designation Article number
Multiflex 20V 2.0Ah spare battery 6.200.000.303
Errors and faults
The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.
Troubleshooting tasks which require the housing to be opened
must only be carried out by an authorized specialist electrical
company or by Trotec.
Light smoke or odour is emitted during the first use:
• This is not a fault. These phenomena disappear after a
brief runtime.
The battery does not charge:
• Check whether the battery is inserted correctly in the quick
charger.
Slide the battery into the quick charger in a way that the
battery terminals engage in the quick charger. The battery
must lock in place in the quick charger.
• Check the power connection.
• Check the power cable and mains plug for damage.
• Check the on-site fusing.
• Check the quick charger for damage. If the quick charger
is damaged, stop using it. Contact the Trotec customer
service.
• Check the battery terminals for dirt. Remove any dirt.
• The battery might be defective and have to be replaced.
Only use batteries of the same type.
The device does not start:
• The battery power might be too low. Recharge the battery.
• Check whether the battery is correctly connected to the
device.
Slide the battery onto the device in a way that the battery
terminals engage. The battery must lock in place in the
device.
• Check the battery terminals for dirt. Remove any dirt.
• The battery is empty. Recharge the battery.
Info
Wait for at least 10 minutes before switching the
device back on.
Strong pressure fluctuations:
• The nozzles are dirty or clogged. Rinse the nozzles with
water. When cleaning the nozzle holes, you can use a
needle.
Water system leaky
• The connections are not installed properly. Switch the
device off and remove the battery. Install the connections
properly as described in the “Start-up” chapter.
• The connection pressure is too high. Only connect the
device to a water supply with a maximum pressure of
5bar.
The device still does not operate correctly after these
checks:
Please contact the customer service. If necessary, bring the
device to an authorised specialist electrical company or to
Trotec for repair.

EN 13
cordless high-pressure cleaner PPWS 10-20V
Maintenance
Activities required before starting maintenance
Warning of electrical voltage
Do not touch the mains plug or the battery with wet or
damp hands.
• Switch the device off.
• Allow the device to cool down completely.
• Remove the battery from the device.
Warning of electrical voltage
Maintenance tasks which require the housing to be
opened must only be carried out by authorised
specialist companies or by Trotec.
Notes on maintenance
Inside the device, there are no parts that need to be maintained
or lubricated by the user.
The device does not require maintenance.
Safety signs on the battery and the charger
Check the safety signs attached to the battery and the charger
at regular intervals. Replace illegible safety signs!
Cleaning
The device should be cleaned before and after each use.
Warning of electrical voltage
There is a risk of a short-circuit due to liquids
penetrating the housing!
Do not immerse the device and the accessories in
water. Make sure that no water or other liquids can
enter the housing.
• Clean the device with a soft, damp and lint-free cloth.
Make sure that no moisture enters the housing. Protect
electrical components from moisture. Do not use any
aggressive cleaning agents such as cleaning sprays,
solvents, alcohol-based or abrasive cleaners to dampen
the cloth.
• Dry the device with a soft, lint-free cloth.
• Keep the connecting terminals on the device and charger
clean.
• Clean polluted or clogged nozzles on the spray lance using
a needle. Remove foreign objects from the nozzles. Rinse
the nozzles through again with water to remove foreign
objects or residues from detergents.
Disposal
Always dispose of packing materials in an environmentally
friendly manner and in accordance with the applicable local
disposal regulations.
The icon with the crossed-out waste bin on waste
electrical or electronic equipment stipulates that this equipment
must not be disposed of with the household waste at the end of
its life. You will find collection points for free return of waste
electrical and electronic equipment in your vicinity. The
addresses can be obtained from your municipality or local
administration. You can also find out about other return options
that apply for many EU countries on the website
https://hub.trotec.com/?id=45090. Otherwise, please contact an
official recycling centre for electronic and electrical equipment
authorised for your country.
The separate collection of waste electrical and electronic
equipment aims to enable the re-use, recycling and other forms
of recovery of waste equipment as well as to prevent negative
effects for the environment and human health caused by the
disposal of hazardous substances potentially contained in the
equipment.
Li-Ion
In the European Union, batteries and accumulators must
not be treated as domestic waste, but must be disposed of
professionally in accordance with Directive 2006/66/EC of the
European Parliament and of the Council of 6September2006
on batteries and accumulators. Please dispose of batteries and
accumulators according to the relevant legal requirements.
Only for United Kingdom
According to Waste Electrical and Electronic Equipment
Regulations 2013 (SI2013/3113) (as amended) and the Waste
Batteries and Accumulators Regulations 2009 (SI2009/890) (as
amended), devices that are no longer usable must be collected
separately and disposed of in an environmentally friendly
manner.

14 EN
cordless high-pressure cleaner PPWS 10-20V
Declaration of conformity
Declaration of conformity in accordance with the ECMachinery
Directive 2006/42/EC, AnnexII, Part1, SectionA
We– Trotec GmbH– declare in sole responsibility that the
product designated below was developed, constructed and
produced in compliance with the requirements of the
ECMachinery Directive in the version 2006/42/EC.
Product model/ Product: PPWS 10-20V
Product type: cordless high-pressure cleaner
Year of manufacture as of: 2022
Guaranteed sound power
level LWA:
92 dB(A)
Relevant EUdirectives:
• 2000/14/EC: 8 May 2000
• 2011/65/EU: 01/07/2011
• 2014/30/EU: 29/03/2014
• 2015/863/EU: 31/03/2015
Applied harmonised standards:
• EN ISO 12100:2010
• EN 55014-1:2017/A11:2020
• EN 60335-1:2012/A2:2019
Applied national standards and technical specifications:
• EN IEC 55014-1:2021
• EN 55014-2:2015
• EN IEC 55014-2:2021
• EN 60335-2-54:2008/A1:2015
• EN 62233:2008
Manufacturer and name of the authorised representative of
the technical documentation:
Trotec GmbH
Grebbener Straße 7, D-52525 Heinsberg
Phone: [phone]
E-mail: [email protected]
Place and date of issue:
Heinsberg, 10.06.2022
Detlef von der Lieck, Managing Director

Trotec GmbH
Grebbener Str. 7
D-52525 Heinsberg
[phone]
[phone]
[email protected]
www.trotec.com