True Furniture Tolgabed User manual

Dimensions
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Assembly Instructions - Please keep for future reference
Tip : To prevent damage,
we recommend that you
build your unit on the
carton(s) it was packed in.
Height - 74cm
Depth - 95,5cm
Width - 195,4cm
Tolgabed 90x190
Argos = 03456 400 800
499/4631
487/7954
487/5877
487/5877 BLUE
487/7954 PINK
499/4631 OAK
Issue: 2 - 23/12/15
DR825206

1
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
•
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
that all bolts and fi ttings are
tightend properly.
Handy Hints
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
Glue safety - Take care when using glue, please follow the advice below•
Important – Please read these instructions fully before starting assembly
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• Check you have all the
components and tools listed
on the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Assembly should be carried out
by a competent adult only.
• do not use this item if any
components are missing
or damaged.
• this item is suitable for childeren
from the age of 6.
Safety and Care Advice

Please check you have all the panels listed below
Components - Panels If you have damaged or missing components,
call the Customer Helpline:
2
03456 400 800
1Drawer Base
(448x344x3)
BO2643
2Drawer left side
(350x120x12,50)
LA1624
3Drawer right side
(350x120x12,50)
LA1625
4Drawer back
(437x120x12,50)
LA1653
5Bed bottom x 2
(1910x467x22)
P1874
6Side back
(1910x383x18)
P1875
7Bed bottom support
(1900x60x28)
P1876
8Backpanel
(486x386x18)
P1877
9Shelf
(486x396x22)
P1878
0Mid Panel x 2
(386x589x18)
P2954
!Drawer front
(480x221x18)
P4131
@Storagebox front x 2
(688x370x18)
P4132
#Side Front
(1910x215x18)
P4747
$Storagebox base x 2
(634x305x15)
P6100
%Storagebox back x 2
(634x250x15)
P6101
^Storagebox
Right side
(323x250x15)
P6102
&Storagebox
left side x 2
(323x250x15)
P6103
*Headboard
(955x740x22)
P6506
(Footboard
(955x740x22)
P6507
)Plinth x 4
(694x92x15)
P7060

Please check you have all the fittings listed below
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
Tools required
Eye protection
(when using a
hammer or glue)
Ruler/tape
measure
0102030405060708090 100 110 120 130 140 150
0123456
Small
hammer
Setsquare
Spirit level
Drill
6mm Suitable drill bit
(for use with wall plug)
Flatblade screwdriver
(medium)
Phillips screwdriver
(medium & large)
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
The screws length ismeasured from thehead to the point (30mm screw shown).
3
Runner right part B x 1
PM1517 RB
W
Runner right part A x 1
PM1517 RA
V
Runner left part B x 1
PM1517 LB
U
Runner left part A x 1
PM1517 LA
T
Wheel x 10
FK1244
S
Glue x 2
FA1510
R
Allen Key x 1
FK1013
Q
(3mm)
Drawerbase support x 4
FK1250
P
L-Bracket x 2
FK1235
O
Wood dowel x 2
FK1410
N
(5x30mm)
Wood dowel x 24
FK1411
M
(8x30mm)
Plug x 2
FK1082
L
(5x9mm)
Expando housing x 16
FK1051
K
Expando Screw x 16
FK10561
J
(5x19,5mm)
15mm
Large locking nut x 40
FK1012
I
(15x12mm)
12mm
Small locking nut x 2
FK1010
H
(12x10mm)
Locking screw x 42
FK1011
G
(5x24mm)
Euro Screw x 4
FK1301
F
(6.3x10mm)
Screw x 4
FK1400
E
(4x15mm)
Screw x 34
FK1311
D
(3x15mm)
Confirmat screw x 16
FK1005
C
(5x40mm)Screw x 14
FK1006
B
(3x45mm)Screw x 5
FK1329
A
(4,5x45mm)

Assembly Instructions
4
S
S
S
S
S
S
14
D
D
D
D
D
D
DD
DD
D
D
14 KK
K
K
K
K
K
K
K
12
G
G
G
G
G
J
J
J
Step - 1
Step - 2
Step - 3
Insert expando housing K
into Storagebox base $.
Make sure that the expan-
do housing Kis open.
Position the wheel Son
the storagebox base $.
Make sure that there is
enough free space to the
edges of storagebox base
$.
Use 2 screws 15mm Dto
mount each wheel Son
storagebox base $.
Screw locking screw G
into storagebox front @.
Note: Insert locking
screw Gas far as shown.
Do not over tighten.
Screw expando screw J
into storagebox front @.
Note: Insert expando
screw Jas far as shown.
Do not over tighten.
2x
2x
2x

Assembly Instructions
5
Step - 4
Step - 5
Step - 6
Put dowels Minto the
holes of Storagebox sides
^/&.
Put drop of glue Rinto the
8 holes of storagebox back
%.
Put dowels Minto the
holes of Storagebox back
%.
Attaching panels
Put drop of glue Rinto the
8 holes of storagebox sides
^/&.
Position the 8 dowels M
of storagebox back %onto
the holes of Storagebox
sides ^/&.
Finished
front edge
Finished
front edge
Finished
front edge
16
J
J
J
J
J
M
M
M
M
17
J
J
R
J
M
M
M
M
M
M
M
M
M
15
16
15 17
R
Screw expando screw J
into storagebox sides
^/&.
Note: Insert expando
screw Jas far as shown.
Do not over tighten.
Screw expando screw J
into storagebox back %.
Note: Insert expando
screw Jas far as shown.
Do not over tighten.
2x
2x
2x

6
Assembly Instructions
Step - 7
Step - 8
Insert large locking nuts I
into storagebox sides
^/&.
Make sure the ‘arrow’ on
locking nuts Ipoints
towards the hole in the
edge of ^/&.
Position storagebox front
@onto the unit.
Use a screwdriver to turn
locking nuts Iclockwise
to lock.
Attaching base
Slide storagebox base $
into the drawer from the
top until the 8 expando
screws Jare totally in
the expando housing Kof
storagebox base $.
Use a screwdriver to turn
expando housig clockwise
to lock.
I
I
I
I
I
16
15
12
17
15
12
14
16
16
12
15
14
17
2x
2x

7
Assembly Instructions
Step - 9
Step - 10
Step - 11
Attaching panels
Put drop of glue Rinto the
6 holes of storagebox sides
2/3.
Position the 6 dowels of
drawer back 4onto the
holes of Storagebox sides
2/3.
Attaching panels
Insert drawer base 1into
the grooves of drawer
sides 2/3and drawer
back 4.
Screw locking screw G
into drawer front !.
Note: Insert locking
screw Gas far as shown.
Do not over tighten.
11
G
G
G
3
4
2
3
4
2
1
R

8
Assembly Instructions
Step - 12
Step - 13
Step - 14
Insert small locking nuts I
into Drawer sides 2/3.
Make sure the ‘arrow’ on
locking nuts Ipoints
towards the hole in the
edge of 2/3.
Fix runner left part B Uon
left drawer side 2as
shown using 15mm screw
D.
Fix runner right part B Won
right drawer side 3as
shown using 15mm screw
D.
2
11
1
4
3
2
4
1
P
P
P
I
I
I
P
P
11
3
2
U
4
1
D
D
D
D
D
D
D
D
11
3
W
Position drawer onto
drawer front !.
Use a screwdriver to turn
locking nuts clockwise to
lock.
Slide drawerbase support
Pin the grooves as shown
and fix them, using the
attached screw.

9
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
GGG
G
G
G
G
G
GG
G
19
18
Assembly Instructions
Step - 15
Step - 16
Screw locking screw G
into headbord *.
Note: Insert locking
screw Gas far as shown.
Do not over tighten.
Screw locking screw G
into footboard (.
Note: Insert locking
screw Gas far as shown.
Do not over tighten.

10
Finished
front edge
Finished
front edge
Finished
front edge
T
T
F
F
FF
FF
F
F
D
D
D D D
DD
D
D
D
D
D
V
V
10
10
I
I
I
I
I
67
N
N
A
A
A
A
A
Assembly Instructions
Step - 17
Step - 18
Put dowels Ninto the
holes of side back 6.
Insert large locking nuts I
into side back 6.
Make sure the ‘arrow’ on
locking nuts Ipoints
towards the hole in the
edge of 6.
Attaching runners
Fix runner left part A T
on mid panel 0as shown
usesing 10mm euro screw
Finto mid panel 0.
Insert 15mm screw Das
shown into mid panel 0
to fix runner left part A T.
Note: look carreful for the
right postion.
Repeat steps with mid
panel 0and runner left
part A V.
Align holes of bed bottom
support 7with holes side
back 6as shown and
attach using 45mm screw
A.

11
Finished
front edge
Finished
front edge
8
9
10
C
C
C
C
C
10 8
9
10
C
C
C
C
C
Assembly Instructions
Step - 19
Step - 20
Position mid panel 0
(with left runner part A T)
onto backpanel 8. Insert
three confirmat screws C
through mid panel 0into
backpanel 8as shown.
Use allen key Qto turn
confirmat screw Cinto
panel.
Position shelf 9onto mid
panel 0. Insert two
confirmat screws C
through mid panel 0into
shelf 9as shown.
Position mid panel 0
(with right runner part A
V) onto backpanel 8and
shelf 9. Insert five confir-
mat screws Cthrough
mid panel 0into back-
panel 8and shelf 9as
shown.
Use allen key Qto turn
confirmat screw Cinto
panel.

12
Finished
front edge
Finished
front edge
9
10
10
8
B
B
G
G
G
G
G
G
G
G
G
9
10
10
8
Assembly Instructions
Step - 21
Step - 22
Screw locking screw G
into mid panel 0.
Note: Insert locking
screw Gas far as shown.
Do not over tighten.
Repeat for mid panel 0
other side
Fix shelf 9onto backpan-
el 8as shown using
45mm screw B.

Finished
front edge
13
19
5
19
I
I
I
I
I
I
I
I
20
20
20
5
a:
b:
Assembly Instructions
Step - 23
Step - 24
Attaching panels
Two people are needed
here.
Position bed bottom 5
onto footboard (.
Use a screwdriver to turn
locking nuts clockwise to
lock.
b: Two people are needed
here.
Position plinth )onto
footboard (.
Use a screwdriver to turn
locking nuts clockwise to
lock.
Repeat for other plinth )
a: Insert large locking nuts
Iinto plinth ).
Make sure the ‘arrow’ on
locking nuts Ipoints
towards the hole in the
edge of ).

14
Finished
front edge
19
20
20
10
10
5
9
8
20
19
10
10 8
5
C
C
C
C
Assembly Instructions
Step - 25
Step - 26
Two people are needed
here.
Position central drawer unit
onto plinths ).
Use a screwdriver to turn
locking nuts clockwise to
lock.
Two people are needed
here.
Attach bed bottom 5with
central drawer unit as
shown and attach using
40mm confirmat screw C.

15
Finished
front edge
I
I
I
19
5
5
19
5
5
C
C
Assembly Instructions
Step - 27
Step - 28
Two people are needed
here.
Attach bed bottom 5with
central drawer unit as
shown and attach using
40mm confirmat screw C.
a: Insert large locking nuts
Iinto bed bottom 5.
Make sure the ‘arrow’ on
locking nuts Ipoints
towards the hole in the
edge of ).
b: Two people are needed
here.
Position bed bottom 5
onto footboard (.
Use a screwdriver to turn
locking nuts clockwise to
lock.

16
Finished
front edge
Finished
front edge
19
5
5
13
19
5
5
13
6
I
I
I
I
I
Assembly Instructions
Step - 29
Step - 30
a: Insert large locking nuts
Iinto side front #.
Make sure the ‘arrow’ on
locking nuts Ipoints
towards the hole in the
edge of #.
b: Two people are needed
here.
Position side front #onto
footboard (.
Use a screwdriver to turn
locking nuts clockwise to
lock.
Two people are needed
here.
Position side back 6onto
footboard (.
Use a screwdriver to turn
locking nuts clockwise to
lock.

17
I
II
I
I
20
19
6
9
5
10
10
8
20
20
20
20
18
18
6
20
20
5
5
10 10
9
B
B
B
B
B
B
B
B
B
B
BB
13
19
Assembly Instructions
Step - 31
Step - 32
b: Two people are needed
here.
Position plinth )onto
central drawer unit.
Use a screwdriver to turn
locking nuts clockwise to
lock.
Repeat for other plinth )
c: Position headboard *
onto bed.
Use a screwdriver to turn
locking nuts clockwise to
lock.
a: Attach bed bottom 5
onto bed bottom support
7using 45mm screw B.
b: Attach bed bottom 5
onto side front #using
45mm screw B.
a: Insert large locking nuts
Iinto plinth ).
Make sure the ‘arrow’ on
locking nuts Ipoints
towards the hole in the
edge of ).

18
19
L
L
L
O
O
O
13
E
E
E
E
E
5
6
18
18 6
20
20
9
5
5
13
19
11
Assembly Instructions
Step - 33
Step - 34
a: Insert plug Linto bed
bottom 5.
b: Position L-Bracket O
onto bed bottom 5as
shown, fix by using 15mm
screw E.
c: Fix L-Bracket Oonto
side front #as shown, fix
by using 15mm screw E.
Inserting drawers
as shown.

19
18
6
9
5
12
12
11
13
19
Assembly Instructions
Step - 35
Inserting storagebox
as shown.
Assembly is complete.