Trufrost IF-200 User manual

USER MANUAL
Flake Ice Maker:
IF 20, IF 50, IF 120, IF 200

User Manual
2
Flake Ice Maker
Instruction Manual
Thank you for selecting our IMS Series Automatic Flake Ice-Maker! To ensure
the proper operation of this ice maker,please read the instruction carefully
before use and please keep it for inspection in case troubles occur.

User Manual
3
CONTENT
FEATURES.................................................................4
NOTES BEFORE OPERATION .....................................4
STRUCTURE..............................................................5
OPERATION PROCEDURES........................................6
TECHNICAL PARAMETERS.........................................7
TROUBLE AND SHOOTING........................................7
CIRCUIT DIAGRAM ...................................................8

User Manual
4
FEATURES:
Our XB-series automatic flake ice makers are designed in cubic shape with the
curved front panel and curved door (or stainless steel flat front panel and flat
door) for nice appearance. Many advantages of the ice maker are available, such
as ice making quickly, great ice making capacity, nice ice shape and ice dropping
quickly. Tap water inlet→water incoming→ ice making→ crush ice → ice
dropping→ ice storing, all these processes are automatically controlled for ice
making continuously. In case of water shortage or ice full in cabinet, the indicator
on the operation board will light on accordingly and the ice maker will stop
operation automatically. The ice storage cabinet is PU foamed, so it is insulated
well and it could prevent the ice made from melting. Also, the remaining water
after ice made each time is used recycling. So not only the water is saved, but
also the ice making efficiency is enhanced and the energy consumption is
reduced, and the customer's ice making cost is also reduced much. Either
purified water or the tap water could be used for ice making.
NOTES BEFORE OPERATION:
1. The incline angle of the cabinet could not be over 45° during
transportation. Don't make ice maker upside-down in case the compressor
or refrigerating system troubles occur.
2. The flake ice maker should be placed on horizontal and structurally sound
ground and away from heat source and corrosive gas. At least about
150mm room should be left around the ice maker to ensure the fine
ventilation.
3. Before using the flake ice maker for the first time, you should wait 12 hours
after positioning it in a proper place.
4. Voltage range:187～242V(220V)
5. The rated capacity of wire should be over 6A, the section area of the wire
is 0.75mm .The wire could be consisted by single ply or multiplies. The
rated current of fuse is 5A.
6. The separate three-pole outlet should be used and the grounding must be
good.
7. If the supply cord is damaged, it must be replaced by the manufacture, its
service agent or similarly qualified persons in order to avoid a hazard.
8. This appliance is not intended for use by children or other persons without
assistance or supervision if their physical, sensory or mental capabilities
prevent them from using it safely. Children should be supervised to ensure
that they do not play with the appliance.

User Manual
5
STRUCTURE:
MAINTENANCE:
1. If the compressor stops for any reasons like water shortage, too much ice,
power off, etc., don't restart it right away. You can restart it about 5 minutes
later.
2. Check regularly the connectors of the water inlet and outlet tubes and drain
the little surplus water that may leak.
3. If the ice make will be unused for a long period, please screw off the plastic
drainage connector screw on the back of the ice maker so as to drain the
surplus water in the water groove. Then screw it on. Wipe the inner liner of
the ice storage container with a clean rag.
4. When plugging or unplugging, the plug should be held by hand and the wires
should not be dragged heavily.
1.Switch
4.Temperature Sensor
7. Power Cable
10. Foot Screw
2.Operation Board
5. Ice Shovel
8. Screw For Drainage
11. Water Inlet Tube
3. Door
6. Back Panel
9. Water Outlet Tube
12. Drainage Tube

User Manual
6
OPERATION PROCEDURES:
1. Unpack the package and take out the attached documents and spare parts
such as the water inlet and outlet tubes, ice shovel and gaskets, etc.
2. Position the ice maker on a well ventilated place and leave at least 150mm
room between the ice maker and the wall. Be sure the ice maker is positioned
levelly and away from the heat source.
3. Make one end of the φ12 flexible plastic corrugated pipe (supplied with the
maker) connected with the water outlet tube on back of the maker, another
pipe end should be placed in a container for surplus water (prepared by user
himself) or in the sewer.
4. Make one end of the water inlet tube (supplied with the maker) connected
with the 3/4" screw type connector of the water tap so as to get the drinkable
tap water. The water pressure of water supply pipe is 1.5～3 bar. The other
end of the water inlet tube should be connected with the screw type
connector of water valve on the back of the ice maker. Be sure to put gaskets
(supplied with the maker) in both ends of the water inlet tube before
connecting. If it is an ice maker for purified water, a φ 12 corrugated pipe
(supplied with the maker) should be used. Connect one end of the pipe with
the purified water supplier (desk-top water dispenser) and another end with
water valve connector on the back of the ice maker. The desk-top water
dispenser should be placed on the ice maker at the back position.
5. Make poser connection and press on the start button on the operation board
for about 4 seconds till the run indicator and the big ice indicator (or small ice
indicator) light on. Then the maker begins to work. All the procedures, water
inlet→ice making→crush ice→ice dropping→ice storing, are controlled
automatically for ice making continuously. If ice is full in the ice storage
container, the ice full indicator on the operation board will light on and the
ice maker will stop automatically. If there is a water shortage or something
wrong with the water supply system, the Water shortage indicator will light
on and the ice maker will stop operation automatically.

User Manual
7
TENCHNICAL PARAMETERS
(tested under the conditions of ambient temperature 15℃ and water temperature 10
Model
Ice making capacity
(Kg/24h)
Power input(W)
Refrigerant
R134a (g)
Dimensions(mm)
IF-20
≤20
280
75
330X470X605
IF-50
≤50
380
115
400X543X700
IF-120
≤120
550
155
500X610X950
IF-200
≤200
1040
280
680X740X1100
The specifications are subject to be changed without notice. Please check the nameplate for
sure.
TROUBLE AND SHOOTING
(FOR REFERENCE OF USERS AND TECHNICIANS)
TROUBLE
CAUSE
REMEDY
The flake ice maker
does not work.
1. The voltage is lower than
the lower limitation
2. The ambient temperature
is too low (Lower than 10℃)
1. Stop the ice maker and
restart it until the voltage
is normal.
2. Try again when the ambient
temperature higher than 10℃.
Water shortage
indicator light on.
1. Water shortage from the
water supply system.
2. Water valve damage.
3. Tap water pressure too low.
1. Check the water supply. If it
is OK, restart the maker.
2. Check the water valve.
3. Be sure the tap water press-
ure is higher than 1.5 bar.
Compressor does
not work.
1. Water shortage.
2. Ice full.
1. Check the water supply
system (water valve and water
supply tube).
2. Take off some ice.
Compressor works,
but no ice is made.
1. Refrigerant leakage.
2. The refrigerating system
is blocked.
1. Recharge the refrigerant and
check the leakage again.
2. Charging N2 to check whet-
her the sysem is blocked and
replace the filter.
3. Check whether the fan is
running.
Water shortage
indicator and ice
full indicator are
glittering at the
same time.
If water inlet jam or running
failure because of low
environmental temperature.
Stop the machine until the
temperature reach 10℃ or
repair it by authorized
service people.

User Manual
8
CIRCUT DIAGRAM:
The symbol on the product or on its packaging indicates that this product may not be treated as household
waste. Instead, it shall be handed over to the applicable collection point for the recycling of electrical and
electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential
negative consequences for the environment and human health, which could otherwise be caused by
inappropriate waste handling of this product. For more detailed information about recycling of this product
TRUFROST COOLING PRIVATE LIMITED
1214 & 1215, Tower B, Emaar Digital Greens,
Golf Course Extn. Road, Sector 61, Gurugram – 122011, Haryana, India
T. [phone] inf[email protected]
www.trufrost.com