TURF TANK One User manual

THANK YOU FOR ADDING TURF TANK ONE TO
YOUR STARTING LINEUP!
Get ready to paint perfect lines while saving money and time.
Your Field Operations Engineer will schedule your onsite
installation and training to provide all the tools you’ll need to
get up and running.
Right now, there are three things you can do to get ready:
Verify the contents of the crate against the crate checklist.
Charge up your Turf Tank Tablet, Robot, and Base Station
batteries.
Relax. We got you.
That’s it!
WELCOME TO
Questions? Get help from a Robot Expert. Call or text: 770-818-6020
1
2
3

GO TO SUPPORT.TURFTANK.COM FOR
PRODUCT MANUALS AND MORE HELP
Something not right? Questions?
Get help from a Robot Expert. Call or text: 770-818-6020
GET TO KNOW
Rover
Front Bumper
Indicator Light
Rover
Rear Wheel
Robot Antenna
Spray Discs
Sprayer Assembly
(Solenoid)
Sprayer-Height
Adjustment Knob
Disc-Width
Adjustment Knob
On/O Switch
Battery/Paint
Compartment
Front Wheel
Back Bumper
Emergency Stop
Shields (Pair)

GO TO SUPPORT.TURFTANK.COM FOR
PRODUCT MANUALS AND MORE HELP
Something not right? Questions?
Get help from a Robot Expert. Call or text: 770-818-6020
GET TO KNOW
Solenoid Power Wire
Spray Shield
Paint Tube
Sprayer Assembly
Quick Fan Cap
Spray Nozzle
Spray Discs
Front Bumper
Disc-Width
Adjustment Knob
Spray Shield
Adjustment Knob
PAINT SYSTEM

GO TO SUPPORT.TURFTANK.COM FOR
PRODUCT MANUALS AND MORE HELP
Something not right? Questions?
Get help from a Robot Expert. Call or text: 770-818-6020
GET TO KNOW
BASE STATION
Pole Battery
8 to 10 hours battery life.
Prism
Pole
View
Capacity
Button
Power
Indicator
Lights
Pole Battery
Base Station
Power
Cable
Base
Station
Antenna Power Port

GO TO SUPPORT.TURFTANK.COM FOR
PRODUCT MANUALS AND MORE HELP
Something not right? Questions?
Get help from a Robot Expert. Call or text: 770-818-6020
GET TO KNOW
BASE STATION
LP-E6 Battery
1½ hours battery life each.
LP-E6 Batteries
Battery Compartment B
Match battery
polarity to lid.
LP-E6 Battery in
compartment lid.
Battery Compartment A

GO TO SUPPORT.TURFTANK.COM FOR
PRODUCT MANUALS AND MORE HELP
Something not right? Questions?
Get help from a Robot Expert. Call or text: 770-818-6020
GET TO KNOW
BASE STATION
ComNav
Battery Cover B
Information Panel
Power Button
Antenna Port
Serial Number
QR Code
Battery Cover A
Position Light
Serial Number and
Product Number
Prism Pole/
Pole Battery
Attachment Port
Key to
Information Panel
Symbols
Position Button
Charging Port
Match red dot on cable to red
line on charging port.

Determine where to place your
Base Station. You will place the
Base Station in this spot every
time you paint.
Install a Turf Tank Ground Spike
(or other semi-permanent marker)
in the selected spot.
Place the Tripod so that the Prism
Pole (center pole of Tripod) rests
in the installed Ground Spike.
Ensure the Tripod’s level bubble is
centered. Make sure the Tripod is
level throughout operation.
Attach the large antenna (12 in)
found in the accessory box to the
Base Station.
Holding the Base Station steady,
attach the Prism Pole or Pole
Battery.
1
2
3
4
5
6
BASE STATION PLACEMENT
DO NOT TURN ON BASE STATION
BEFORE ATTACHING TO PRISM POLE!
GO TO SUPPORT.TURFTANK.COM FOR
PRODUCT MANUALS AND MORE HELP
Something not right? Questions?
Get help from a Robot Expert. Call or text: 770-818-6020

Turn on the Base Station by
pressing the Power button.
On startup, the Base Station
automatically searches for
Saved Position. The orange
Position light flashes to
indicate the search.
When the Base Station has
found a Saved Position, it will:
Show a solid orange
Position Light.
Show a flashing blue
Transmission Light.
Emit five beeping sounds.
If the Base Station does not
detect a Saved Position, it will:
Show no orange
Position Light.
Show no blue
Transmission Light.
Emit a five-second
continuous error tone.
1
2
3
4
USE AN EXISTING BASE
STATION POSITION
To search for a Saved Position at any time
other than startup, press the Position button.
GO TO SUPPORT.TURFTANK.COM FOR
PRODUCT MANUALS AND MORE HELP
Something not right? Questions?
Get help from a Robot Expert. Call or text: 770-818-6020
Pole Battery
Height
Markings
Prism Pole 8 to 12 ft
Ground
Spike
Bubble Level
Tripod

Turn on the Base Station by
pressing the Power button.
Press and hold the Position
Button until you hear a short
beep from the Base Station.
Signs you have created a
Saved Position:
The orange Position Light is
lit and steady.
The blue Transmission Light
is flashing.
The Base Station emits five
beeping sounds.
Once a Saved Position has
been successfully created, you
must turn the Base Station
power o and turn it on again.
The Base Station is now ready
to use.
You must power cycle the
Base Station EVERY TIME
you set a new position.
Raise the Base Station on the
Prism pole 10-12 feet to its
operational height.
1
4
25
3
CREATE A BASE STATION
POSITION
You are ready to create
your field plans!
GO TO SUPPORT.TURFTANK.COM FOR
PRODUCT MANUALS AND MORE HELP
Something not right? Questions?
Get help from a Robot Expert. Call or text: 770-818-6020
LEAVE AT LEAST 30 YARDS
BETWEEN MULTIPLE SAVED
POSITIONS.

Best Practices for Mixing Robot Paint:
These are general guidelines. Contact Turf Tank Support or your
Field Operations Engineer for brand-specific instructions.
Pour water into an empty 5.5
gallon jug:
For a mix ratio of 4:1
(bright) use four gallons
of water.
For a mix ratio of 3:1
(brighter) use three gallons of
water.
Pour one gallon of paint
concentrate into the jug.
Mix with drill bit for at least
90 seconds or up to two full
minutes for even pigment
dispersal.
1
2
3
PAINT: CONCENTRATE
GO TO SUPPORT.TURFTANK.COM FOR
PRODUCT MANUALS AND MORE HELP
Something not right? Questions?
Get help from a Robot Expert. Call or text: 770-818-6020

Instructions:
Cone Nozzle Flat Fan Nozzle
SHAKE AND GO!
USE LESS PAINT! CUSTOM RESULTS!
PAINT: RTS
GO TO SUPPORT.TURFTANK.COM FOR
PRODUCT MANUALS AND MORE HELP
Something not right? Questions?
Get help from a Robot Expert. Call or text: 770-818-6020
Ideal for: General purpose
sports, rounded edges
Shake vigorously or use drill
mixer bit for 30 seconds and
you’re ready to paint!
Ideal for: Football hashes,
logos, sharp edges
(READY TO SPRAY)

Robot, Tablet, or Base Station not working as they should?
Check the following first:
Are the batteries in the Tablet, the Robot, and for the Base
Station fully charged?
Is the Robot’s battery seated properly in its compartment?
Is the compartment latch locked?
Are the antennas attached to the Base Station and the
Robot?
Is the Emergency Stop button engaged? Are the Bumper
stop mechanisms engaged?
Is the Tablet connected to the Robot’s WiFi? Is the Robot
connected to the App (does the Robot appear in the App)?
Is the WiFi blocked?
Is the Tablet receiving a cellular signal? Is Roaming Data
turned on? Is the cellular signal strong? Do 4G and R
appear above the cell signal indicator on the Tablet?
Reboot the Robot and the Tablet. Shut them down
completely, then power up again.
Still having trouble?
Call or text 770-818-6020 for help.
1
2
3
4
5
6
7
BASIC TROUBLESHOOTING
GO TO SUPPORT.TURFTANK.COM FOR
PRODUCT MANUALS AND MORE HELP

Charge batteries EVERY DAY.
Charge Robot Batteries.
Charge the Tablet.
Charge the Base Station batteries (Pole Battery or LP-E6
batteries).
Monitor battery life on the Tablet, Robot, and Base
Station.
If you paint multiple fields a day, consider upgrading to a Pole
Battery or buying additional LP-E6 batteries.
For best performance and to prevent damage, keep batteries
on all components above 25% charge.
Check the field you are painting for obstacles or bad
field condition.
Clean Robot thoroughly after EVERY use.
Remove Quick Fan Cap, Spray Nozzle, Gasket, and Chamber
Reducer. Wash them all with warm water.
Run warm (not hot) water through the Paint System (hoses,
pump, sprayer) until clear.
Remove the Mesh Filter from the housing on the tube in the
Paint System and wash it in warm water.
IMPORTANT DAILY TASKS
GO TO SUPPORT.TURFTANK.COM FOR
PRODUCT MANUALS AND MORE HELP