2.2 Camera Dimensions
Figure 2-2 Dimensions （Unit: mm）
Special Announcement
For more information, please refer to website.
Fully understand this document before using this device,
and strictly observe rules in this document when using this
device. If you install this device in public places, provide the
tip "You have entered the area of electronic surveillance" in
an eye-catching place. Failure to correctly use electrical
products may cause fire and severe injuries.
ŸStrictly observe installation requirements when installing
the device. The manufacturer shall not be held responsible
for device damage caused by users' non-conformance to
these requirements.
ŸStrictly conform to local electrical safety standards and use
power adapters that are marked with the LPS standard
when installing and using this device. Otherwise, this
device may be damaged.
ŸUse accessories delivered with this device. The voltage
must meet input voltage requirements for this device.
ŸIf this device is installed in places with unsteady voltage,
ground this device to discharge high energy such as
electrical surges in order to prevent the power supply from
burning out.
ŸWhen this device is in use, ensure that no water or any
ŸAvoid heavy loads, intensive shakes, and soaking to
prevent damages during transportation and storage. The
warranty does not cover any device damage that is caused
during secondary packaging and transportation after the
original packaging is taken apart.
ŸProtect this device from fall-down and intensive strikes,
keep the device away from magnetic field interference, and
do not install the device in places with shaking surfaces or
under shocks.
ŸClean the device with a soft dry cloth. For stubborn dirt, dip
the cloth into slight neutral cleanser, gently wipe the dirt
with the cloth, and then dry the device.
ŸDo not jam the ventilation opening. Follow the installation
instructions provided in this document when installing the
device.
ŸKeep the device away from heat sources such as radiators,
electric heaters, or other heat equipment.
ŸKeep the device away from moist, dusty, extremely hot or
cold places, or places with strong electric radiation.
ŸIf the device is installed outdoors, take insect- and
moisture-proof measures to avoid circuit board corrosion
that can affect monitoring.
ŸRemove the power plug if the device is idle for a long time.
ŸBefore unpacking, check whether the fragile sticker is
damaged. If the fragile sticker is damaged, contact
customer services or sales personnel. The manufacturer
shall not be held responsible for any artificial damage of the
fragile sticker.
ŸAll complete products sold by the manufacturer are
delivered along with nameplates, quick setup guide and
accessories after strict inspection. The manufacturer shall
not be held responsible for counterfeit products.
ŸThe manufacturer will update this manual according to
product function enhancement or changes and regularly
update the software and hardware described in this manual.
Update information will be added to new versions of this
manual without prior notice.
ŸThis manual may contain misprints, technology information
that is not accurate enough, or product function and
operation description that is slightly inconsistent with the
actual product, the final interpretation of company is as a
standard.
ŸThis manual is only for reference and does not ensure that
the information is totally consistent with the actual product.
For consistency, see the actual product.
Precautions
Open the package, check the appearance of product for no
obvious damage, and confirm the item list for table 1-1 is
consistent.
Table 1-1 Packing list
2.1 Device Ports
Different device may have different ports and multi-head
cable, please refer to the actual product.
Different device may have different dimensions, please
refer to the actual product.
NOTE
NOTE
NOTE
liquid flows into the device. If water or liquid unexpectedly
flows into the device, immediately power off the device and
disconnect all cables (such as power cables and network
cables) from this device.
ŸDo not focus strong light (such as lighted bulbs or sunlight)
on this device. Otherwise, the service life of the image
sensor may be shortened.
ŸIf this device is installed in places where thunder and
lightning frequently occur, ground the device nearby to
discharge high energy such as thunder strikes in order to
prevent device damage.
It alerts you to moderate dangers which, if not
avoided, may cause minor or moderate injuries.
It alerts you to risks. Neglect of these risks may
cause device damage, data loss, device
performance deterioration, or unpredictable
results.
It provides additional information.
NOTE
CAUTION
WARNING
WARNING
CAUTION
1
Device Structure
2
Packing List
Network access port protective cover
Component Quantity Remark
1
1
1
Figure2-1 Multi-head cable
1
Table 2-1 Multi-head cable description
Figure 2-3 Install SD card
Port
1
2
3
4
5
IN
OUT
GG
Connects to a standard Ethernet
cable or PoE . The green light is on,
the network connection is normal;
the yellow light flashes when the
data is transmitted. Some models
maybe not have the lights, please
refer to actual product.
Connects to an external audio
device such as a speaker.
Applied for
camera with
audio
function
Receives an analog audio signal
from devices such as a sound
pickup device.
Connects to a 12V direct current
(DC) power supply.
Applied for
alarm
function
2
1
ID
3
5
Network
access port
Support PoE
supply.
Core Description Remark
Audio output
Power supply
(DC 12V)
Audio input
port
OUT
IN
G
G
4
30
2-1/4UNC x8
275
273~~303 ajustable
70
70
4-φ4.5
98
100
95 107
Reset PWR SD
Page 1 Page 2 Page 3 Page 4
Appearance
