TV One CM-AVIP-IN-1USB-1ETH User manual

Firmware versionM406and above
QSG-CM-AVIP-IN-V1.40
Mar 2019
CM-AVIP-IN-1USB-1ETH
Dual stream input module
Quick Start Guide V1.40

In this guide
About your Dual stream input module 2
Quick start guide 3
Checking and updating the CORIOmaster firmware 11
Checking your firmware version and
downloading new firmware 11
Updating the firmware 13
Regulatory compliance 13
Contact us 14
Get more help
There are more Quick Start Guides available on the USB drive that
came with your CORIOmaster. CORIOgrapher now comes with fully
searchable help, just select and search, or ask a question.

QSG-CM-AVIP-IN-V1.40 1
Thanks for buying this Dual stream input module. The Dual stream
input module allows you to decode and play media and images from
a USB drive or internal storage, and video streams from IP sources.
Sources include streaming server, and from any device when used
with an IP encoder, such as the Magenta™Encoder-100.
Features
nPlay two simultaneous channels of media, including IP streams
nPlay video clips from USB drive up to 4K@30Hz
nPlay single IP streams up to 100 Mb/s
nPlay dual IP streams up to 40 Mb/s
nPlay still images up to 8K
nPlay streams with low latency
nPlay media from streaming server
nCreate and save up to 20 playlists
nPrimary channel supports up to 4K@30Hz
nSecondary channel supports 1080p@60Hz
nIP streams up to 1080p@60Hz
nFull resolution and frame rate scaling
nStart playing media when your CORIOmaster™ starts
nSupports USB 2.0 and USB 3.0
n16 or 128 GB internal storage
This Quick Start Guide assumes that your Dual stream input module
is installed in a CORIOmaster™, CORIOmaster mini™, or
CORIOmaster micro™.
If you need help installing your Dual stream input module, contact
your supplier, consult an experienced AV installer, or contact tvONE
support. Contact details are at the back of this guide.

2 tvONE
About your Dual stream input module
USB
(LED)
Indicates the status of the USB drive. Green means that
the USB drive is working correctly. Red means that the
USB drive is over current.
USB3.0
USB2.0
Connect a USB drive to play media directly.
For best results, we recommend using quality USB
drives compatible with USB 3.0.
ST1
(LED)
Indicates the status of the card. Green means that the
card is working correctly. Red means that the card is
starting, or that there is a problem.
ST2
(LED)
Indicates the status of the module. Green means that
the module is working correctly. Red means that the
module is starting, or that there is a problem.
LAN Connect an Ethernet cable to play media over IP.
If any status indicator stays red, restart your CORIOmaster. If that
doesn't work, contact tvONE support. Contact details are at the
back of this guide.
Supported formats
The Dual stream input module supports the following formats:
Multimedia container
formats
.mp4, .mov, .mkv,
.m4v, .ts, .mts,
.m2ts, .mt2
Embedded audio
formats
.mp3, .aac

QSG-CM-AVIP-IN-V1.40 3
Quick start guide
It's easy to get started with the Dual stream input module, but if you
want more help with any of these steps, or with setting up and using
streaming media, select in CORIOgrapher™ and search, or ask a
question.
Setting up the Dual stream input module
1. Connect your cables and power on your CORIOmaster™,
CORIOmaster mini™, or CORIOmaster micro™.
To stream media, connect an Ethernet cable to the Dual stream
input module, or connect a USB drive to play media directly.
For 4K media, use a good quality, high-speed 3.0 USB drive.

4 tvONE
Make sure your CORIOmaster is connected to your display
devices and to an AC power outlet.
2. Download the latest firmware for your CORIOmaster from
tvone.com/firmware-updates.
3. Use CORIOdiscover to update your firmware.
Read more about updating firmware on page 11.
4. Download the latest version of CORIOgrapher from
tvone.com/softwares.
5. Install the latest software.
The latest version of CORIOgrapher includes help files. If you need
help with any of the following steps, select in CORIOgrapher
and search, or ask a question.

QSG-CM-AVIP-IN-V1.40 5
Connecting to CORIOgrapher™ and choosing network
settings
1. Open CORIOgrapher , connect to your CORIOmaster, and read
the configuration from your device.
Make sure you have a video wall set up that includes at least one
window that uses a source from the Dual stream input module,
and select Take.
2. OPTIONAL: if you only want to play media from a USB drive,
you don't need to do this step.
If you want to stream media over IP, choose network settings for
your Dual stream input module.
Select > Module Configuration.
Find the Dual stream module that you want to set up, and select
>Configure.

6 tvONE
If you choose DHCP, the network assigns you an IP address.
If you choose a static IP address:
nEnter a value for your IP address and subnet mask.
nIf you want to stream from the internet, enter a value for
your gateway.
nIf you want to refer to a source by name, enter a value for
DNS.
Static IP address
If you choose a static IP address, make sure you enter a unique
value for your IP address. Using the same IP address for multiple
devices can cause your devices to disconnect.
If you need help with network settings, contact your network
administrator.

QSG-CM-AVIP-IN-V1.40 7
Playing media and streams
1. Double-click the window you wish to play streaming media, and
select (Media Player) Manage.
2. Select your media source.
Your media items appear as icons.
Still image Saved stream
Video clip Found encoder
Playlist Found encoder,
streaming

8 tvONE
Information about the media item appears on the right.
3. OPTIONAL: if you want to stream media, add your streams.
nIf you want to stream from an Encoder-100, check that it is
encoding. Look for the green spot.
If the encoder is not encoding, you might need to start or
configure it.
Read about starting and configuring the Encoder-100 in
CORIOgrapher Help
nIf you want to stream from the internet, or from an encoder
that does not appear in Discovered encoders, add the