TVILIGHT CitySense Plus User manual

CitySense Plus
Installation Manual
English
PR 60-0005-00 | Rev. F | 05/10/2020

PR 60-0005-00 | Rev. E | Page 2 of 11
In order to function properly, CitySense Plus must be
connected to a dimmable driver/ballast.
NOTE: Some dimmable drivers/ballasts must be
programmed/set to dimmable mode. If this has not been
done, CitySense Plus will not be able to dim the connected
armature.
ATTENTION:
TVILIGHT PROJECTS BV / Beechavenue 162-180, 1119 PS, Schiphol-Rijk, the Netherlands
[email protected] / www.tvilight.com

PR 60-0005-00 | Rev. E | Page 3 of 11
In box:
You’ll need:
Sticker
TVILIGHT
www.tvilight.com
TVI-CSP1-01-0014
5m Cable
CitySense Plus M16 Cable Gland
OR
20 mm Rubber Grommet
Scan&Go App
Available in the
Apple App Store
and in the
Google Play Store
Drill
M16 Thread
Generic Strap x 2
Max = 11mm
Min = 8mm
Wago x 4

PR 60-0005-00 | Rev. E | Page 4 of 11
1. Run wire through Cable Gland/Grommet
2. Drill hole into the pole:
- M16 threaded (Cable Gland) OR
- 20 mm (Grommet)
5m
Note: for added protection against rust, the use of an anti-corrosion spray such as WD40
Corrosion inhibitor or equal is recommended.

PR 60-0005-00 | Rev. E | Page 5 of 11
3. Run wire through hole in the pole
OR
4. Insert Cable Gland/Grommet into hole in
the pole
OR

PR 60-0005-00 | Rev. E | Page 6 of 11
5. Screw Cable Gland OR press Grommet into
the pole
OR
6. Strap product to the pole
* Ensure Tensioning Tool is set
to maximum tension (#4)
Tensioning Tool

PR 60-0005-00 | Rev. E | Page 7 of 11
7. Level the product
Position 2: Standard
1
2
3

PR 60-0005-00 | Rev. E | Page 8 of 11
SAME
TVILIGHT
www.tvilight.com
TVI-CSP1-01-0014
TVILIGHT
www.tvilight.com
TVI-CSP1-01-0014
TVILIGHT
www.tvilight.com
TVI-CSP1-01-0014
8. Apply product ID sticker to pole
2 m

PR 60-0005-00 | Rev. E | Page 9 of 11
TVILIGHT
www.tvilight.com
TVI-CSP1-01-0014
TVILIGHT
www.tvilight.com
TVI-CSP1-01-0014
9. Add device to CityManager
1. Download Tvilight Scan&Go from Apple iOS App Store or from Google Play Store.
2. Login with your Username and Password.
3. Use the ‘Add device’ function in Scan&Go app to add the device to CityManager.
4. The location of the new device is determined by Scan&Go’s GPS and it will be
indicated on the map.
5. The Device Serial Number will be added when scanning the QR-Code with the
camera.
6. Fill in the required fields (the ones with an asterisk), select the device type and
also select the type of ballast (PWM or DALI-Logarithmic or DALI-Linear).
Note: The type of ballast must be known before installation.
7. Press save and move to next device.
For more information on how to use Scan&Go app, please visit:
https://www.tvilight.com/scan-go/

PR 60-0005-00 | Rev. E | Page 10 of 11
DC +
Connector
(e.g. Wago)
AC in(N)
AC in(L)
DC -
L
N
Junction Box
GND
GND NL L out N out
DC-DC+
GREEN BROWN WHITE
BLACK GREY
BLUE RED
Wiring Diagram
WARNING:
If not correctly connected product might not
function or it might be permanently damaged.

PR 60-0005-00 | Rev. E | Page 11 of 11
ARMATURE
JUNCTION BOX
GND
GND
0-10V+
or
DALI+ N
N
L
L
L
GND
N
L
CITYSENSE +
Lout Lin Nin
N
DC-
DC+
0-10V-
or
DALI-
0-10V-
or
DALI-
0-10V+
or
DALI+
GND
GREEN BROWN WHITE BLACK GREYBLUE RED
NLLout Nout
0-10V-
or
DALI-
0-10V+
or
DALI+
Wiring Diagram
WARNING:
If not correctly connected product might not
function or it might be permanently damaged.
Note: For added protection, an external circuit breaker at the
power input of the product is mandatory. Circuit breakers such as
the ELeQ LS-94 5L2408 or similar rated products are acceptable.