twotrees TT403UF User manual

250KG CAPACITY
SUITABLE FOR: CLASSIC AND ROD HAMMOCKS
FROM 280(W) x 360(L)cm
DELUXE UNIVERSAL
HAMMOCK STAND
TT403UF
PRODUCT MANUAL
WARNING
Read instructions before use and keep for future reference. Failure to read
these instructions before use can lead to an increased risk of injury. When
installing always check with a qualied builder for safety. Two Trees will
only guarantee the performance of this product when used with other Two
Trees products. i.e. if non Two Trees hammocks or stand are used, the
guarantee is void.

2
Thank you for purchasing a Two Trees hammock.
We at Two Trees know the importance of spending time relaxing. Hence we’ve developed
a range of quality hammocks and convenient accessories that come with easy to follow
instructions so that you will be relaxing in no time. It is important to read all instructions before
use and take care when using your hammock. Please ensure that you adhere to the following
safety measures to get the maximum enjoyment from your new hammock.
WARNING
Read instructions before use and keep for future reference. Failure to read these
instructions before use can lead to an increased risk of injury. When installing always
check with a qualied builder for safety.
1. Assembly must be carried out by an Adult.
2. Ensure hammock is fully assembled
before use.
3. DO NOT exceed the maximum load of
250kgs.
4. The maximum capacity of the hammock
stand is 200kgs, only if hooks and screws
are secured into position according to the
instructions provided.
5. DO NOT climb into hammock feet rst.
6. DO NOT stand in hammock.
7. DO NOT dive into or jump about in
hammock.
8. DO NOT stick your head through the
suspension cords.
9. Keep suspension cords as straight as
possible, DO NOT twist.
10. Inspect frame feet and ensure they are
stable before use.
11. DO NOT use damaged or weakened
hammock hanging accessories.
12. Hammock fabrics and accessories will
wear over time and use. Always check the
loading capacity and condition of parts
before use.
13. Hammocks are not designed for swinging,
playing, climbing or to be used as a
children’s toy.
14. DO NOT leave children or pets unattended
in or near hammock.
CAUTION AND SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
15. Hammock fabric, suspension cords and
hanging accessories will become worn
over time and use. Always inspect prior to
use and DO NOT use if items show signs
of damage or weakness.
16. Always check the loading capacity before
use.
17. Keep hammock clear of obstructions.
18. Allow a minimum of 50cm clearance range
around the perimeter of your hammock
when in use (Fig. 1).
19. Only use the hammock on level oors with
shock-absorbing properties such as
carpet or outdoor grass to minimise the
risk of injury in case of an accident.
DO NOT use on slippery or hard surfaces.
20. Never use a free standing brick wall to
hang your hammock.
21. Only use Two Trees accessories for
hanging your hammock.
22. DO NOT modify hammock. Hammock
must be used in accordance of this
manual.
23. DO NOT smoke in or around the
hammock. Keep away from heat or
ames.
24. DO NOT use whilst wearing shoes,
clothing, jewellery or accessories that have
a hook and loop fastener.
25. DO NOT use near sharp objects.
26. A copy of this manual must be provided should
the hammock transfer ownership.

THE TWO TREES
HAMMOCKS RANGE INCLUDES
3
SAFETY INSTRUCTIONS
There are many ways to hang your hammock,
here are some of our favourite and recommended
options:
BETWEEN
TWO POSTS
BETWEEN
TREES
BETWEEN
TWO WALLS
ON HAMMOCK
STAND
SELECTING THE LOCATION

4
DO NOT twist or knot suspension cords
when hanging.
Hammocks will stretch by 5-10% after
the rst few uses. Adjustments can be
made after each use to keep you and your
hammock comfortable.
THINGS TO CONSIDER
WARNING
Read instructions before use and keep for future reference. Failure to read these
instructions before use can lead to an increased risk of injury. When installing
always check with a qualied builder for safety.
This hammock stand is adjustable in size from 295cm to 369cm in length. Therefore, the space
you require to assemble this hammock stand will depend on the total length of the hammock you
intend to use (not included).
HAMMOCK STAND MIN SIZE:
295cm (L) x 99cm (W) x 99.5cm (H)
HAMMOCK STAND MAX SIZE:
369cm (L) x 99cm (W) x 115 cm (H)
Suitable for hammocks with a
minimum of 280cm from end to end
Suitable for hammocks with a maximum
of 360cm from end to end
280cm(L) 360cm(L)

50cm
50cm
50cm50cm
Hammock
Maximum
Length
> 250KGS
5
DO NOT leave children or pets
unattended in or near hammock.
DO NOT exceed the maximum load
of 250kgs.
Allow a minimum of 50cm clearance
range around the perimeter of your
hammock when in use. <Fig.1>
THINGS TO CONSIDER

3.0m
1.8m
20 - 30cm
6
HOW TO HANG
YOUR HAMMOCK
TEMPORARY INSTALLATIONS
For temporary installations, such as trees or beams, we recommend using the Two Trees
hammock hanging kit (TT501HK). For more information about our installation products please
visit our website (www.twotreeshammocks.com.au)
Place the cord around the pole
or tree, then thread through the
gure eight hook.
Thread the cord through the
clamp hook and secure at
desired length.
Repeat process for other side of
hammock. Ensure both hooks are
secure, place hammock ends over
hooks.
1 2
3
To hang your Two Trees hammock you will require
two xed points, such as trees, beams, posts, or
dyna bolts into brick walls. Alternatively you can
purchase a Two Trees Universal Stand. Consult a
qualied builder if unsure.
WARNING: Never use a free standing
brick wall to hang your hammock.
Your Two Trees hammock will require a minimum of 3 metres between xing points to get the
ideal shape. Rope may be needed to attach one end of the hammock, it is recommended to
use a double piece to avoid the hammock twisting.
Hang the hammock loops at roughly the same height. When the hammock is in use it should sit
20-30cm above the ground.

Hammock Spring
Hammock Hook
Strong & Secure
7
HOW TO HANG
YOUR HAMMOCK
We recommend using the
Two Trees screw eye and
hook (TT502HH) with the Two
Trees springs (TT503HS) The
spring is optional.
NOTE: It is recommended
to use structurally sound,
strong timber posts that are
10cm square or more. When
installing always check with a
qualied builder for safety.
For sturdy masonry walls (not air/hollow/single brick or besser block) a 10mm dyna bolt with a
large washer and rope can be used.
For detailed installation instructions on (TT503HS) Two Trees Spring, please refer to the
Two Trees website.
www.twotreeshammocks.com.au or scan the below QR code.
Read instructions before use and keep for future reference. Failure
to read these instructions before use can lead to an increased risk of
injury. When installing always check with a qualied builder for safety.
WARNING:
DO NOT EXCEED THE MAXIMUM LOAD OF 250KGS
PERMANENT INSTALLATIONS
TEMPORARY INSTALLATIONS
For temporary installations that are portable and do not require a xed point we recommend
using the Two Trees Universal Stand (TT403UF).
Assemble and set up your universal
stand according to the included
instructions that were included with
your Universal Stand.
Attach the hammock onto the hooks at
either end ensuring the hammock and
suspension cords are not twisted.
12

8
ENJOYING
YOUR HAMMOCK
HOW TO RELAX IN YOUR HAMMOCK
CARING FOR YOUR HAMMOCK STAND
Open the hammock fabric in the centre of
the hammock and slowly and safely sit in
the middle as you would in a chair.
Bring your feet in and stretch them out, so you
are lying on a diagonal. This is the traditional
way to relax in a classic style hammock.
Gently lie back on a diagonal with your
head on the edge of the hammock.
To ensure the lifespan of your Two Trees hammock stand, do not leave exposed to the
elements for prolonged periods when not in use. Store away when not in use, as the sun and
rain will deteriorate the construction over time.
To keep your hammock stand in good condition, apply a light coating of surface protectant wax
to the outer surface. Store in dry place.
1 2
3

9
LIST OF PARTS
AEnd angle tube with wheel hole 1
B End angle tube 1
C Centre base extension pipe, 36mm DIA x 840mm 1
D Metal stand pipe 40mm DIA x 980mm 2
E Metal arm pipes with xed hooks, 42mm DIA x 910mm 2
F Male extension pipes, 36mm x 560mm 2
G Wheel assembly screw 1
H Wheel 2
I Wheel assembly nut 1
J Wheel assembly washer 2
K Plastic external collar 6
L Plastic Inside collar 4
M Plastic stand feet 4
N Tri wing hand screws 14
HAMMOCK STAND MIN SIZE: 295(L) x 99(W) x 99.5(H)cm
Suitable for hammocks with a minimum of 280cm from end to end.
HAMMOCK STAND MAX SIZE: 369(L) x 99(W) x 115(H)cm
Suitable for hammocks with a maximum of 360cm from end to end.
UNIVERSAL HAMMOCK
STAND PARTS

10
HAMMOCK STAND
ASSEMBLY INSTRUCTIONS
a. Insert part L(plastic inside collar) into both ends of the short tube on part A(end angle
tube with wheel hole). Ensure the cut-out detail on the collars aligns with the holes on
the short tube.
b. Thread part D(metal stand pipe) through the tube at the bend of part A(end angle tube
with wheel hole) and secure in place with 2 part N(tri wing hand screws).
c. Assemble the part H(wheels) to either side of part A(end angle tube with wheel hole)
using parts G(wheel assembly screw), I(wheel assembly nut) and J(wheel assembly
washer).
d. Attach part K(plastic external collar) by pushing onto both ends of part A(end angle
tube with wheel hole).
e. Push to attach part M(plastic stand feet) onto both ends of part D(metal stand pipe).
Ensure that the at ridged detail is facing the ground.
1

11
a. Insert part D(plastic inside collar) into both ends of the short tube on part B(end angle
tube). Ensure the cut-out detail on the collars aligns with the holes on the short tube.
b. Thread part D(metal stand pipe) through the tube at the bend of part B(end angle tube)
and secure in place with 2 x part N(tri wing hand screws).
c. Attach part K(plastic external collar) by pushing onto both ends of part B(end angle tube).
d. Push to attach part M(plastic stand feet) onto both ends of part D(metal stand pipe).
Ensure that the at ridged detail is facing the ground.
2
HAMMOCK STAND
ASSEMBLY INSTRUCTIONS

12
HAMMOCK STAND
ASSEMBLY INSTRUCTIONS
a. Insert part C(centre base extension pipe) into the middle of parts A(end angle tube
with wheel hole) and B(end angle tube) leaving 2 spacing holes visible.
b. Using part N(tri wing hand screws) secure part C(centre base extension pipe) to parts
A(end angle tube with wheel hole) and B (end angle tube).
3

13
a. Attach part K(external collar) onto the ends of both part E (metal arm pipe with xed
hook) components.
b. Insert part F(male extension pipe) into part A(end angle tube with wheel hole) and
part B(end angle tube) and secure with a part N(tri wing hand screw) for both tubes.
c. Slide part E (metal arm pipe with xed hook) over part F(male extension tube) and
secure with 2 x part N(tri wing hand screw) for at each end.
a. Stand can be adjusted in length and in height as your hammock stretches over time
making it taught again.
b. We recommend setting the frame up on the shortest settings rst then adjusting
as required.
c. Your hammock should not sag onto the ground once you sit in it, there should be
a medium taught ness in length height o the ground.
4
5
HAMMOCK STAND
ASSEMBLY INSTRUCTIONS
NOTE: Make sure you have the same amount of visible holes at each end of the stand.

14
Made in China exclusively for Mayo Hardware Pty Ltd
4 Secombe Place, Moorebank NSW 2170 Australia
Customer Service Phone: [phone]
www.mayohardware.com.au | 2021©
For more information visit
www.twotreeshammocks.com.au
We will honour all statutory guarantees that this product is
of acceptable quality. (including that it is t for purpose)
Issue A