Classic Exhibits Gravitee Inline GK-1013 Manual

© 2023
Order #XXXXX
Top View
10’
10’
GK-1013 10’ x 10’ Gravitee Inline
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS

© 2023
Order #XXXXX
Locked layer contains
placeholder marks.
= 1 sq foot
GK-1013 Grid View

© 2023
Order #XXXXX
Assembly Assembly Cont’d
Side-by-Side Assembly
1) Frames: Place frames side-by-side with one higher than the
other, then slide panel down to lock panels securely together.
2) Corner Connectors: Repeat Step 1 for installing corner
connectors to frames.
Side-by-Side Disassembly
1) Pull pin lock outwards to disengage.
2) Pull frames upward and apart at the same time to detatch.
Push pin lock into hole of connecting frame.
Note: Block on pin lock will secure in groove.
Pin Lock
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
Graphic Removal
SEG Graphic Installation
Corner A
Corner D
Corner B
Corner C
It is important to first insert graphic
into each alternate corner, then to
the sides of the frame.
If this is not done, graphic will not fit
into the frame correctly.
Step 1
Insert corner A.
Turn edge of graphic so silicon welt
is perpendicular to face of graphic.
Insert narrow side of welt with fabric
to outside into the channel.
Repeat for other side of this corner.
Step 2
Repeat Step 1 for opposite corner
C, then insert corner B, followed by
corner D, to complete the
installation of the corners.
Step 3
Once all corners are inserted, press
one silicon edge into channel from
corners and work toward the center.
Make sure welt is fully inserted into
channel. Continue until all sides are
done. Smooth out edges of graphic.
To remove the graphic from
the frame, locate the fabric
pull tab.
Gently pull up on the tab to
remove the fabric.
General Information

© 2023
Order #XXXXX
Straight Connection
All knobs must be tightened securely to ensure a proper connection.
All knobs must be tightened securely to ensure a proper connection.
Adjust connectors if necessary to
prevent gaps in connection.
Upper Horizontal Extrusion
Lower Horizontal Extrusion
Straight Connector
Straight Connector
Corner
Connectors Corner
Connectors
Corner
Connectors Corner
Connectors
COMPLETED ASSEMBLY
3) Tighten all knobs to secure connection.
Slide verticals over
lower connectors.
Then slide upper
connectors into
groove of verticals.
Tighten all knobs.
When assembling frame, first attach all straight
connectors, then attach corner connectors.
1) Place extrusions end-to-end.
2) Loosen all knobs, then slide straight
connectors across the seam of extrusions.
Disassembly
1) Loosen all knobs.
2) Slide connectors off of one extrusion.
3) Tighten knobs to prevent loss during
packing & shipping.
CEI110 Profile
Slide both connectors across seam of extrusions.
Tighten all knobs.
Corner Connection
3) Tighten all knobs to secure connection.
Disassembly
1) Loosen knobs on vertical extrusions.
2) Slide the vertical extrusions off of
corner connectors on lower and upper
horizontal extrusions.
1) Loosen knobs, then slide vertical extrusions onto
corner connectors of lower horizontal extrusion.
2) Slide corner connectors of upper horizontal
extrusion into grooves of vertical extrusions.
Keep straight connectors in groove of
extrusion. Do not remove connectors
during disassembly.
CEI110 Frame Assembly

© 2023
Crate 1 of 1
Order #XXXXX
Locked layer contains
placeholder marks.
CRATE PACKING
Crate Packing

© 2023
Step 1 of 4
Order #XXXXX
11
15
12
6
6
5A
13
8
9
10
7
14
Completed Assembly
Item
5A
6
7
8
9
10
11
12
13
14
15
Qty.
1
2
1
1
1
1
1
1
1
1
1
Description
Base Plate
47.307” Z45 Horizontal Extrusion
95” Gravitee Corner Connector
95” Gravitee Corner Connector
30”w x 95”h Gravitee Panel w/ (2) 91.904“ S44
30”w x 95”h Gravitee Panel w/ (2) 91.904“ S44
38”w x 95”h Gravitee Panel w/ Door
95” Gravitee Hinged Corner Connector
47.123”w x 95”h Gravitee Curved Panel w/ (2) 91.904“ S44
95” Gravitee Hinged Corner Connector
94.5”h Gravitee Corner Connector
Steps:
1) Attach base plate [5A] to panel [10]. See Base Plate detail.
2) Assemble panels and connectors in numerical order, as shown.
See Gravitee Assembly Instruction sheet for details.
3) Attach horizontals [6] between connectors [7] and [8], as shown.
4) Install SEG graphic to assembled panels. See General
Information sheet for SEG Graphic Installation instruction.
Keep S44 verticals attached to Gravitee panels
[13] [9] and [10].
Base
Plate
Bolt
5A
Bolt
Gravitee
Panel
[10]
Attach base plate [5A] to panel [10],
using bolts, washer, and wing nut.
Washer
Wing Nut
Base Plate
*
*
GK-2012 Backwall Assembly

© 2023
Step 2 of 4
Order #XXXXX
3
9
13
10
Completed Assembly
*
Steps:
1) Connect lights to top of panels [3] [9] and
[10]. See Light Connection detail.
2) Attach shelves to panels [9] and [10].
See Shelf Attachment detail.
3) Attach monitor mount to panel [13]. See
Monitor Mount Attachment detail.
Monitor
Mount
Attach monitor mount to vertical extrusions,
using screw standoffs and screw caps.
Note: Mount attaches over SEG graphic.
Screw
Cap
*Monitor Mount Attachment
Standoff
SEG
G
r
a
phic
Shelf Attachment
Lock Set Screw
Insert locks into groove
of Gravitee panel then
tighten set screws.
Back of Shelf
Shelf
Shelf
Shelf
Shelf
Shelf
Shelf
Slide light onto clip then lock clip
into groove of horizontal extrusion.
Light Connection
Clip
Light
Light
Clip
Horizontal Extrusion
GK-2012 Backwall Attachments

© 2023
Step 3 of 4
Order #XXXXX
Locked layer contains
placeholder marks.
*
*
1A
1
2
2A
78
8
8A
8A
7
Shelf
Support
7A
3
3A
4
5
6
Door
Door
Infill
Infill
Item
1,1A
2,2A
3,3A
4
5
6
7,7A
8,8A
Qty.
1,1
1,1
1,1
1
1
1
2,2
2,2
Description
46.25” CEI110 Horizontal Extrusion
37.5” CEI110 Vertical Extrusion
37.5” S44 Vertical Extrusion
37.5” S44 Vertical Extrusion w/ Door Hinges
37.5” S44 Vertical Extrusion w/ Door Stops
37.5” S44 Vertical Extrusion w/ Door Hinges
14.153” Z45 Horizontal Extrusion
20.408” Z45 Horizontal Extrusion
7A
*
*
Transformer
to power
++
+
-
-
-
to power
Lights
Male
Male
Female
Female
Transformer
96W / 4A / 24V
Light to Light Connection
Light to Transformer Connection
Maximum of 7 light bars per transformer.
Steps:
1) Assemble CEI110 extrusions [1] [1A] [2] and [2A], inserting
2-piece Sintra light blocker. See CEI110 Frame Assembly sheet for instruction.
2) Connect lights and transformer. See Light Connection details.
3) Attach horizontals [7] and [8] between verticals [3] [4] [5] [6] and [3A].
4) Slide infills between verticals [3] [4] and [3A] [6], making sure Velcro
is facing inward.
5) Connect doors to verticals [4] and [6]. See Door Connection detail.
6) Attach horizontals [7A] and [8A] between verticals [3] [4] [5] [6] and [3A].
7) Connect shelf supports to Velcro on infills.
Keep counter sides assembled, when packing.
Sint
r
a
Ligh
t
B
l
o
c
ker
Sint
r
a
Ligh
t
B
l
o
c
ker
Door
Hinge
Hinge
Slide pin into
hinge attached
to vertical.
Slide door
hinge over pin.
Door Connection
*
Pin
MOD-1700 Cabinet with USB Ports

© 2023
Step 4 of 4
Order #XXXXX
*
Counter Top
Shelf
Align hole with pin Rotate pin. Spring
will push pin into hole.
Counter Top Attachment
12
*
Pin
Hole
*
Steps:
1) Attach assembled frame to verticals [3] and [3A].
See Frame Attachment detail.
2) Install SEG graphic to front of assembled frame.
See SEG Graphic Installation detail.
3) Place shelf inside assembled base on top of pins and supports.
4) Place counter top on assembled base, then secure with pins.
See Counter Top Attachment detail.
Completed Assembly
3
3A
Attach frame to
connector on
vertical extrusion,
using bolt.
Frame Attachment
Bolt
Connector
*
*
*
Graphic Removal
To remove the graphic from
the frame, locate the fabric
pull tab.Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
SEG Graphic Installation
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C
SEG Graphic
*
MOD-1700 Cabinet with USB (Cont’d)