Tyco RDU Mk2 Assembly instructions

RDU Mk2
REMOTE DISPLAY UNIT
INSTALLATION & PROGRAMMING MANUAL
RDU PRODUCT MANUAL
Document Number: LT0499
Issue ....... 1.02; ............ 8 April 2015
- A P P R O V A L S -
AUSTRALIAN STANDARD AS1603.4 1987 (Incl. Amdt 1 & 2):
AUSTRALIAN STANDARD AS4428.1 1998 (Incl. Amdt 1 & 2):
AUSTRALIAN STANDARD AS4050 1992 (Int)
AUSTRALIAN/NZ STANDARD AS/NZS3548 1995 Class A
NEW ZEALAND STANDARD NZS4512
The RDU is a product of
Tyco Fire Protection Products
Level 3, 95 Coventry Street
Melbourne VIC 3006
AUSTRALIA
Phone: [phone]
NOTICE
Information contained in this document is copyright, and shall not be reproduced in any form whatsoever,
or its contents disclosed to any third party, without the written consent of Tyco (The Company). Information
contained in this document is believed to be accurate and reliable, however the company reserves the right
to change the content without prior notice.
COPYRIGHT (C) 2015
TYCO FIRE PROTECTION PRODUCTS

RDU Mk2 Installation & Programming Manual Document No: LT0499
Page ii 8 April 2015 Issue 1.02
TYCO FIRE PROTECTION PRODUCTS
END USER LIABILITY DISCLAIMER
The RDU has a configuration programming facility which may be accessed from the keypad
by using a password.
This programming facility allows the user to define detail of the operation of the RDU. It is
possible for the user to program operational features that prevent the installed RDU from
meeting statutory requirements.
Tyco Fire Protection Products does not accept responsibility for the suitability of the
functions programmed by the user.
CISPR 22/AS3548 NOTICE
WARNING: This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
AMENDMENTS
ISSUE
DATE
COMMENTS
ECO
1
16/01/09
Original. Derived from LT0148 & LT0256
3995
1.01
01/07/10
Added limitations on use on MX1 in Section 7.9.
1463
1.02
08/04/15
Added IP Ratings & max dc current to specs.
4731

Document No: LT0499 RDU Mk2 Installation & Programming Manual
Issue 1.02 8 April 2015 Page iii
TABLE OF CONTENTS
End User Liability Disclaimer....................................................................................... …… ii
Amendments ............................................................................................................ …… ii
CHAPTER 1 INTRODUCTION 1-1
1.1 SCOPE................................................................................................................................... 1-2
1.2 ASSOCIATED DOCUMENTATION....................................................................................... 1-3
1.3 PRODUCT HISTORY LOG.................................................................................................... 1-4
1.4 GLOSSARY OF ABBREVIATIONS ......................................................................................1-4
1.5 GLOSSARY OF TERMINOLOGY .........................................................................................1-5
CHAPTER 2 SYSTEM DESCRIPTION 2-1
2.1 OVERVIEW............................................................................................................................2-2
2.2 PHYSICAL STRUCTURE......................................................................................................2-7
2.3 SYSTEM STRUCTURE ......................................................................................................... 2-9
2.4 NEW ZEALAND MODE OPERATION ................................................................................ 2-15
CHAPTER 3 SYSTEM SPECIFICATIONS 3-1
3.1 GENERAL..............................................................................................................................3-2
3.2 MECHANICAL SPECIFICATIONS........................................................................................3-3
3.3 ELECTRICAL SPECIFICATIONS ......................................................................................... 3-4
3.4 INPUT SPECIFICATIONS .....................................................................................................3-7
3.5 OUTPUT SPECIFICATIONS ................................................................................................. 3-9
3.6 CONTROLS .........................................................................................................................3-13
3.7 DISPLAYS ...........................................................................................................................3-14
CHAPTER 4 ORDERING INFORMATION 4-1
4.1 ORDERING INFORMATION.................................................................................................. 4-2
CHAPTER 5 CONFIGURING AN RDU 5-1
5.1 GENERAL..............................................................................................................................5-2
5.2 MODULE CONFIGURATION ................................................................................................ 5-2
5.3 BATTERY & POWER SUPPLY.............................................................................................5-3

RDU Mk2 Installation & Programming Manual Document No: LT0499
Page iv 8 April 2015 Issue 1.02
5.4 LINKS ON PCB MODULES ..................................................................................................5-7
CHAPTER 6 PROGRAMMING PART 1 6-1
6.1 INTRODUCTION....................................................................................................................6-2
6.2 PROGRAMMING OR VIEWING THE DATABASE...............................................................6-9
6.3 DATABASE OPERATIONS, INITIALISING, ACCESSING, SAVING .................................. 6-9
6.4 PROGRAM BASE MENU, TEXT & GLOBAL PARAMETERS .........................................6-14
6.5 RDU PROGRAMMABLE PARAMETER LIST ....................................................................6-37
6.6 ERROR MESSAGES DURING CONFIGURATION............................................................6-41
CHAPTER 7 PROGRAMMING PART 2 7-1
7.1 SYSTEM CONFIGURATION MENU .....................................................................................7-2
7.2 CONFIGURING ZONES ........................................................................................................7-3
7.3 OUTPUT LOGIC .................................................................................................................. 7-10
7.4 OUTPUTS & ANCILLARY RELAYS...................................................................................7-21
7.5 OPERATION OF WARNING SYSTEM/EXTERNAL BELL & ANCILLARY RELAYS....... 7-23
7.6 CONVERTING AN RDU Mk1 DATABASE TO RDU Mk2 .................................................. 7-25
7.7 ZONE LED MAPPING & CONFIGURATION ...................................................................... 7-28
7.8 TANDEM LCD MODE..........................................................................................................7-33
7.9 CONFIGURING AN RDU FOR AN MX1 PANEL................................................................ 7-34
CHAPTER 8 INSTALLATION & WIRING 8-1
8.1 INSTALLATION : MAF & NON-MAF CONFIGURED RDU................................................8-2
8.2 INSTALLATION : MAF RDU................................................................................................. 8-8
8.3 SLIMLINE RDU –MCP WIRING .........................................................................................8-17
8.4 INSTALLATION : NZ DISPLAY EXTENDER BOARD & BRIGADE DISPLAYS..............8-18
CHAPTER 9 ALIGNMENT, ADJUSTMENT & PLACING INTO OPERATION 9-1
9.1 ALIGNMENT & ADJUSTMENT............................................................................................. 9-2
9.2 PLACING INTO OPERATION...............................................................................................9-3
APPENDIX A - RDU CONFIGURATION FORMS……………………………………………..A-1

Document No: LT0499 RDU Mk2 Installation & Programming Manual
Introduction
Issue 1.02 8 April 2015 Page 1-1
CHAPTER 1
INTRODUCTION

RDU Mk2 Installation & Programming Manual Document No: LT0499
Introduction
Page 1-2 8 April 2015 Issue 1.02
1.1 SCOPE
This manual describes the installation and programming of the RDU Mk2 (Remote Display
Unit) for systems compliant with one of the following standards.
AS4428.1 Australian Standard
AS1603.4 Australian Standard (legacy systems)
NZS4512 : 2003 New Zealand Standard
The RDU Mk1 is the original RDU and uses software versions 1.00 to version 2.12 and
requires an AS1603.4 keypad. The operator manual for RDU Mk1 is LT0133 and the
installation and programming manual is LT0148.
The RDU Mk2 requires software version 5.xx and is available in two series –AS1603.4 and
AS4428.1 –to match the keyboard layout and operation. The part numbers and manuals
associated with RDU Mk2 are shown in the following table.
Table 1.1
RDU Mk2 Part Numbers
AS1603.4
AS4428.1
15U Cabinet MAF/PSU 3A
FP0558
FP0785
8U Cabinet MAF/PSU 3A
FP0585
FP0786
Slimline Wall Mount
FP0559
FP0787
Slimline Flush Mount
FP0772
FP0788
4U 19” Rack Module
FP0577
FP0789
Operator Manual
LT0494
LT0252
Installation & Programming Manual
LT0499
The RDU can be used in both New Zealand and Australia and this manual describes the
operation for both. There are some differences in operation between the two countries and
these are listed in section 2.4. The country mode is selected with a programmable
parameter.
The manual is divided into the following chapters:
Chapter 1 Introduction: Information on this manual.
Chapter 2 System Description: A description of the RDU and how it interacts with the
FIP.
Chapter 3 System Specifications: A detailed specification for the RDU.
Chapter 4 Ordering Information: Part numbers for the various system components.
Chapter 5 Configuring an RDU: General information and detail on fitting of the various
links and components when configuring a system.
Chapter 6 Programming Part 1: Details for programming "global data".
Chapter 7 Programming Part 2: Details for programming "system configuration".
Chapter 8 Installation & Wiring: Detail of installation and field wiring.

Document No: LT0499 RDU Mk2 Installation & Programming Manual
Introduction
Issue 1.02 8 April 2015 Page 1-3
Chapter 9 Alignment, Adjustment & Placing Into Operation: Detail on how to adjust
an RDU in the field and place it into operation.
Appendix A RDU Configuration Forms: A set of master forms for recording
programming information for an RDU.
1.2 ASSOCIATED DOCUMENTATION
1.2.1 PRODUCT RELATED
The following manuals for the RDU Mk2 are available:
RDU Mk2 Installation & This Manual, Part No. LT0499.
Programming Manual
RDU Mk2 AS4428.1 Operator's Manual Part number LT0252.
RDU Mk2 AS1603.4 Operator's Manual Part number LT0494.
1.2.2 STANDARDS
This manual makes reference to the following Australian Standards:
AS4428.1 Fire Detection, Warning, Control and Intercom Systems -
Control and Indicating Equipment
Part 1 : Fire
AS1603.4 Automatic Fire Detection and Alarm Systems
Part 4 - Control and Indicating Equipment.
AS4050 (int) (AS1603.4 systems) Fire Detection and Fire Alarm Systems -
Fire Fighter's Control and Indicating Facilities.
AS1670.1 Automatic Fire Detection and Alarm Systems - System Design,
Installation and Commissioning.
and the New Zealand standard:
NZS4512 : 2003 Automatic Fire Alarm Systems in Buildings

RDU Mk2 Installation & Programming Manual Document No: LT0499
Introduction
Page 1-4 8 April 2015 Issue 1.02
1.3 PRODUCT HISTORY LOG
1.3.1 HARDWARE
PA0871 AS4428 CONTROLLER/DISPLAY, RDU
PA0909 AS4428 CONTROLLER/DISPLAY, NO SOFTWARE. (Customer spare)
PA0798 AS1603.4 CONTROLLER/DISPLAY, RDU
PA0804 AS1603.4 CONTROLLER/DISPLAY, NO SOFTWARE. (Customer spare)
PA0491 MAF/PSU AS1603.4
PA0873 MAF/PSU AS4428.1
PA0703 REMOTE TERMINATION BOARD
1.3.2 SOFTWARE
SF0424 SOFTWARE RDU Mk2 AS4428 / AS1603 REMOTE DISPLAY V5.00
1.4 GLOSSARY OF ABBREVIATIONS
The following abbreviations are used throughout this manual:
A/C : Air Conditioning
ac : Alternating Current
AEOL : Active End of Line
AHr : Ampere Hour
ANC 1 : Ancillary Relay 1
AZC : Alarm Zone Circuit, or Detection Zone
AZF : Alarm Zone Facility, or Group
AVF : Alarm Verification Facility, or Check Alarm
Bd : Board
CIE : Control & Indicating Equipment
Char : Character
CCT : Circuit
COM : COMMON relay contact
dc : Direct current
EEPROM : Electrically Erasable Programmable Read Only Memory
ELV : Extra Low Voltage
EOL : End Of Line (device)
EOLR : End of Line Resistor
Expn : Expansion
E2 : Electrically Erasable Programmable Read Only Memory
FFCIF : Fire Fighter's Control & Indicating Facility
FIP : Fire Indicator Panel
FRC : Flat Ribbon Cable
I/O : Input/Output
LCD : Liquid Crystal Display
LED : Light Emitting Diode
MAF : Master Alarm Facility
Max : Maximum

Document No: LT0499 RDU Mk2 Installation & Programming Manual
Introduction
Issue 1.02 8 April 2015 Page 1-5
Min : Minimum
MCP : Manual Call Point (Break Glass Switch)
MOV : Metal Oxide Varistor (Used for Surge Protection)
msec : Millisecond
NC : Normally Closed
NO : Normally Open
No : Number
Nom : Nominal
PC : Personal Computer (small computer)
PCB : Printed Circuit Board
PSU : Power Supply Unit
PTC : Positive Temperature Co-efficient (Thermistor)
RMS : Root Mean Square
Reqd : Required
RTC : Real Time Clock
RDU : Remote Display Unit
sq mm : square millimetre
Tmnl : Terminal
VA : Volts Amperes
VB : Battery Backed Voltage
VNB : Non Battery Backed Voltage
+VBF : Fused Battery-Backed Voltage
+VNBF : Fused Non-Battery-Backed Voltage
Z1 : Zone Number 1 (program abbreviation)
Zn1 : Zone Number 1 (text abbreviation)
1.5 GLOSSARY OF TERMINOLOGY
The following terminology is used throughout this manual:
Ancillary Equipment : Equipment external to Fire Alarm system
Ancillary Relay : Relay in RDU which operates Ancillary equipment
Auto-Reset : Mode for one person testing of detectors
Auxiliary Output : Output for driving additional LEDs/relays
Baud : Bits per second
Control Output : Output from RDU to other equipment
Default : Pre-programming option or logic equation i.e. one that
exists without the user programming it.
Detector : Alarm Detection Device (electrical transducer)
Fire Control Station : Fire Brigade Authority, or any other authority which
receives the FIP alarm signals.
Mapping : Programmable causal relationship between inputs and
outputs
Zone : Fire searchable area of building represented by a
unique number and name in the RDU, and associated
with the FIP AZC of the same number.
Display extender board : Used with New Zealand operation only. It has common
normal, fire and defect LEDs.

RDU Mk2 Installation & Programming Manual Document No: LT0499
Introduction
Page 1-6 8 April 2015 Issue 1.02
THIS PAGE INTENTIONALLY LEFT BLANK