U-Line UACP115-IS01A Installation manual

USER GUIDE & SERVICE MANUAL
Model: UACP115-IS01A

USER GUIDE & SERVICE MANUAL
u-line.com
Table of Contents
Installation
Integrated Panel Dimensions
Integrated Panel Installation
Grille Installation

USER GUIDE u-line.com
Introduction
WELCOME TO U-LINE
Congratulations on your U-Line purchase! Your product comes from a company with decades of premium modular ice
making, refrigeration, and wine preservation experience. U-Line creates products focused on functionality, style, and
inspired innovations — paying close attention to even the smallest details. Applications include residential, outdoor, ADA
height compliant, marine, and commercial. Product categories include Beverage Centers, Wine Refrigerators, Ice Machines,
Refrigerators, Freezers, and Dispensers. Our advanced refrigeration systems, large and exible capacities, and clean
integrated look are what makes our products Built-In to Stand Out®. Since 2014, U-Line has been part of the Middleby family
of brands. Products are designed, engineered, and assembled in Milwaukee, Wisconsin, USA, and select products are available
worldwide.
U-Line — RIGHT PRODUCT. RIGHT PLACE. RIGHT TEMPERATURE.®
PRODUCT INFORMATION
Looking for additional information on your product? User Guides, Spec Sheets, CAD Drawings, and Product Warranty
information are available digitally on u-line.com.
PROPERTY DAMAGE / INJURY CONCERNS
In the unlikely event property damage or personal injury is suspected related to a U-Line product, please take the following
steps:
1. U-Line Customer Care must be contacted immediately at +1.414.354.0300.
2. Service or repairs performed on the unit without prior written approval from U-Line is not permitted. If the unit has been
altered or repaired in the eld without prior written approval from U-Line, claims will not be eligible.
GENERAL INQUIRIES
U-Line Corporation
8900 N. 55th Street
Milwaukee, Wisconsin 53223 USA
Monday - Friday 8:00 am to 4:30 pm CST
T: +1.414.354.0300
Email: [e-mail]
u-line.com
CONNECT WITH US
SERVICE & PARTS ASSISTANCE
Monday - Friday 8:00 am to 4:30 pm CST
T: +1.414.354.0300
Service Email: [e-mail]
Parts Email: [e-mail]
Designed, engineered and assembled in WI, USA
3

USER GUIDE u-line.com
Integrated Panel Dimensions
Integrated Panel Dimensions
Integrated Door Panel for
15” (381mm) wide unit
14-⁄”
(375 mm)
⁄”
(16 mm)
to
⁄”
(19 mm)
30-⁄”
(773 mm)
NOTE
Panel thickness may be 5⁄8” or 3⁄4”. Center the unit in the
15” opening. If the hinge side of the unit is pressed against
the adjacent cabinet, use a 5/8” thick panel.
Maximum panel weight is 15 lbs.
4

USER GUIDE u-line.com
Integrated Panel Installation
Integrated Panel Installation
Cut and prepare panels according to the information
provided in the Integrated Panel Dimensions section.
It is important to use the factory provided grille that came
with the product to assure proper air ow is maintained
through the condenser. The use of a custom grille is not
recommended and will void the warranty.
REMOVE DOOR
See Door Adjustments section.
ASSEMBLE THE PANEL TO THE DOOR
1. With the door laying on a at
surface and starting at the corner
of the door, remove the magnetic
door gasket from the interior side
of the door. Set the gasket aside
on a at surface.
2. Align the panel to the door. Make sure the sides and
top are ush.
3. With bar clamps or “C” clamps, secure the panel to
the door
4. At each of the 10 holes in the gasket extrusion
channel, drill pilot holes into the wood panel. Use
the drill size from the chart in the table below being
careful not to drill through the front surface of the
panel.
5. Fasten the panel to the door with the 10 screws
provided in the literature pack.
6. Remove the clamps and replace the gasket in the
gasket extrusion channel. Some force may be required
to seat the gasket into the channel. Be sure the
gasket corners are seated correctly.
INSTALL THE DOOR
See Door Adjustments section.
CAUTION
!
Wood
Panel
Door/Drawer
Bar
Clamp
Bar
Clamp
Integrated panel
flush with top of
door.
Integrated panel
flush with side of
door.
Holes in gasket
extrusion channel
Material Type #10 Wood Screw
Hardwood 1⁄8” (3.2mm) Diameter Pilot Hole
Softwood 7⁄64”
(2.8mm) Diameter Pilot Hole
5

USER GUIDE u-line.com
Grille Installation
Grille Installation
REMOVING AND INSTALLING GRILLE
Disconnect electric power to the unit before
removing the grille.
When using the unit, the grille must be installed.
Do NOT touch the condenser ns. The condenser
ns are SHARP and can be easily damaged.
Removing the grille
1. Disconnect power to the unit.
2. Remove the two screws.
3. Remove grille from unit.
Installing the grille
1. Align cabinet and grille holes and secure, but do not
over tighten grille screws.
2. Reconnect power to the unit.
WARNING
!
WARNING
!
Condenser
Screws
6