U-Line H-4406 User manual

PAGE 1 OF 4 0214 IH-4406
πH-4406
ALUMINUM
BLEACHERS
3-ROW x15'
1-800-295-5510
uline.com
WARNING! DO NOT ALLOW THESE
ALUMINUM BLEACHER COMPONENTS
TO GET WET! COMPONENTS THAT
ARE BUNDLED AND GET WET WILL
DISCOLOR!
NOTE: If components are to be stored
where they may be subjected to moisture,
break bundles and separate or restack
leg-to-leg so that components have
no flat surfaces touching together. This
will prevent chemical reaction which is
unsightly, but purely cosmetic.
NO CLAIMS WILL BE ALLOWED FOR SUCH
ALUMINUM DISCOLORATION.
CAUTION! All outdoor bleachers must be
anchored to meet wind loads as specified
by applicable building codes.
PARTS
Tape Measure
Square Rubber Mallet
End Cap x 10
Socket Wrench
#8 x 1/2"Self-Tapping
Stainless Screw x 20
5/16" Carriage Bolt x 30 5/16" Flange Nut x 30
3/8" Bolt x 8 3/8" Flange Nut x 8
Frame x 3
X-Brace with End Notches x 2
X-Brace without End Notches x 2
Clip x 30
15'x 10" x 2" Anodized Seat Plank x 3
15'x 10"x 2" Mill Foot Plank x 2
TOOLS NEEDED
1/2" Deep Well
Socket
9/16" Deep Well
Socket
Electric Drill
with #2 Phillips Bit 9/16" Wrench

PAGE 2 OF 4 0214 IH-4406
1. Attach end caps to seat planks and foot planks.
Make sure the pre-drilled holes on the end caps
are on the underside of the planks. Use a rubber
mallet to tap into place. Attach with a drill and #2
Phillips bit #8 x 1/2" self-tapping stainless screws.
(See Figure 1)
2. Assemble X-braces. Use one X-brace with the
notches on the ends and one X-brace without end
notches. Place the pieces together flat side to flat
side. Attach with a 3/8" bolt and flange nut through
the center hole. Hand tighten. Repeat for second
X-brace. (See Figures 2 and 3)
3. Position frames in place, standing up, 6 feet apart.
(See Figure 4)
4a. Working from the back of the frames, attach the
assembled X-brace: notched end to the third hole
up from the bottom and the other end to the right
frame bottom hole. Attach with 3/8" bolts and
flange nuts. Hand tighten. (See Figures 5-8)
ASSEMBLY INSTRUCTIONS
3/8" Bolt and Flange Nut
Figure 2
Figure 1
#8 x 1/2" Self-Tapping Screws
2 x 10 End Cap
2 x 10 Plank (upside down)
Figure 3
6'
6'
Figure 4
Figure 5
Bleacher Frame
X-Brace
Flange Nut
3/8" Bolt
Figure 6

PAGE 3 OF 4 0214 IH-4406
4b. Using other end of assembled X-brace from the
right frame, attach to the bottom hole and third
hole up from the bottom on the middle frame.
With the second assembled X-brace, attach to
the middle frame using the same bottom hole
and third hole up from the bottom (the brace ends
overlap). Only one notched end may be on the
bottom hole and one on the third hole up from the
bottom. Hand tighten. (See Figure 9)
4c. Attach assembled X-brace to the left frame using
the other end of assembled X-brace. Hand tighten.
NOTE: Not all holes on the frame will be used.
4.
5. At this point frame is able to stand up on its own.
Make sure the frame is straight, square and level.
Tighten all 3/8" bolt connections with socket wrench.
(See Figure 10)
6. On the frame, place a clip on each hole of the
seat and foot braces. On the foot braces, use the
intermediate holes. The clips should have the center
indent facing up and be horizontal. Insert 5/16"
carriage bolt through each clip and frame and
attach nut loosely. (See Figures 11 and 12)
ASSEMBLY INSTRUCTIONS CONTINUED
Figure 10
Intermediate
Holes
Figure 12
Fi g u r e 11
Figure 9
Figure 7 Figure 8

PAGE 4 OF 4 0214 IH-4406
7. Attach foot planks. Beginning with the bottom row,
place one foot plank on top of the clips, making
sure the clips rest under the plank in the outside
channels. The foot plank should have an 18"
overhang on both ends, measuring from the center
of the frame. Repeat for second foot plank.
(See Figure 13)
8. Confirm the frame is straight and square. Center of
the left foot plank frame to center of the right foot
plank frame should measure 6'on center.
(See Figure 14)
9. Underneath the foot plank, turn the clips vertical so
the grooves of the clip fit securely under
the channel lips. Tighten the
clips with flange nuts.
(See Figures 15-17)
10. Attach the seat planks. Starting from the top row,
place one seat plank on top of the clips, making
sure the clips are resting under the plank in the
outside channels. (See Figure 18)
11. The seat planks should have an 18" overhang on
both ends, measuring from the center of the frame.
Make sure the seat end is square with the foot
planks (should line up corner to side). Repeat for the
remaining seat planks. (See Figure 19)
12. Tighten all clip connections with socket wrench.
Seat Plank
Foot Plank
Frame
Figure 18
ASSEMBLY INSTRUCTIONS CONTINUED
5/16" Carriage Bolt
Flange
Nut
Hold Down Clip
Fi gure 17
18"
Figure 13
6'
Figure 14
Figure 16
Figure 19
Figure 15
π CHICAGO • ATLANTA • DALLAS • LOS ANGELES • MINNEAPOLIS • NYC/PHILA • SEATTLE • MEXICO • CANADA
1-800-295-5510
uline.com