UIS WPW-220A User manual

Wireless Power Switch (US)
Installation Guide
4
3
2
1
Overview
Name:Wireless Power Switch (US)
Power:100~120VAC
Dimension:82 x 59.5x 53.7mm
Features
Home Automation – receive the Gateway’s issued ON/OFF signal wirelessly,then control the power outlet for power supply.It
can easily operate the home appliances,even by using a mobile device.
Easy Setup – simply press the SET button on the device to join the system.
Switch Link – when linked with other sensors,users can configure the action to be taken when the linked sensor is triggered.
For example,if someone triggered the Contact Sensor,the Power Switching will automatically turn ON/OFF. It is suitable to be
used as a power switch to control the corridor night auxiliary lighting.
When linked with other home appliances,press the ON/OFF button to manually turn on/off the power relay.(The Red light
indicates the power is ON)
Equipped with a router function which enables the system to extend the wireless signal distance and lets other sensors join the
system via its connection.
Easy to monitor the power consumption of home electronic appliances for energy saving.
Names of Parts
1. Antenna
2. Triplex Outlet
3. Power Plug
4. ON/OFF Button
5. Status LED
6. SET Button
6
5
82mm
53.7mm
59.5mm
WPW-220A
IV. Device Deletion (Back to factory default settings)
1. First, Login into website.
About Login methods, please refer to 4.Basic Setting of Installation in Wireless Gateway Installation Guide. (Page1).
2. To remove the device joining, pull out the device, long press SET button at the bottom of the device about 10 seconds. Plug in
the device to the wall outlet again and wait 5 seconds. (Please see next page to continue the procedure.)
Installation
I. Before Installation
1. Power on the Gateway.
2. Waiting for about 90 seconds until the Gateway led light become solid green instead of blinking.
Note: We suggest to use auto joining all device via APP at the rst time. Please refer to APP Quick Installation Guide.
II. Device Installation and Manual Joining
1. Plug in the device to the wall outlet.
2. Short press the SET button at the top of the Gateway or at the bottom of Router (another Power Switching).Then short press the
SET button on the device
3. The Gateway/Router and the device are joining as both LED indicators blink (around 30 seconds). Wait for few seconds until both
LED indicators are turned o, indicating the device Joining process is successful.
Note: If the device Joining process is failed, both LED indicators on those joined devices will light blue once after blinking.
4. To switch on the power, simply press the ON/OFF button. (The red light indicates the power is ON)
III. Device Usage
Power Meter: Plug the home appliance on the Power Switch. Then it can calculate the Voltage(V), Current(A), Power(W),
Frequency(Hz) when the device is switched ON. (The minimum Watt will appear after the device is switched on for at least 1 hour)
Energy Used Cost: Congure the unit cost at peak time and o-peak time by Web interface rst, and then select the accumulate
period (by month, the maximum is 3 months). The system will automatically calculate the Total Cost, Peak Time Cost, and
O-Peak Time Cost. (The earliest period is 1 year ago)
The power meter value and cost value can be viewed on the web interface and APP.

Notice
Maximum resistive load: 10A/120V, 1200W.
Power meter range:
i. Measure voltage range: 100~120VAC
ii. Measure current range: 1~10A
iii. Measure power range: 30~1200W
iv. The accumulate period is by month, and the maximum period is 3 months. (The earliest period is 1 year ago)
When the Power Switch works as a router, the maximum joined sensors is 16. The maximum router in a system is 16.
The maximum wireless signal cascade-able is 3 levels.
Troubleshooting
Problem Solution
Specifications
Wireless Power Switch (US)
The LED indicator lights abnormally
when linking to the system
Cannot link to the system
a. Make sure the device is properly connected to the wall outlet.
b. Reset to factory default (Please see Installation,IV. Device Deletion), and
re-join to the system.
c. If the problem persists, please contact your local distributor.
Check the wireless signal and the distance between device and Gateway/Router
(line of sight) is 300 meters (max.). If there is any obstructions (i.e. walls or metal
objects) between the devices, the distance will be shorter. Users can move the
device closer or add a Router,then try again.
Communication Protocol / Frequency
Operation Range
Operation Voltage
LED Indicator
Operation Interface
Resistive Load
Inductive Load (Single Face)
Over Current Protection
Output Load Current Range
Output Load Power Range
Operating Temperature
Storage Temperature
Humidity
Dimension (W x H x D)
Weight
Zigbee Pro ZHA1.2 / 2.4 GHz ISM band
Up to 300 meters (LOS)
100~120VAC
Blue 1PC/Red 1PC , LED Status: Relay (ON/OFF)
Push button
10A/120VAC, 1200W max
0.5HP/120VAC
11A
1~10A±10%
30~1200W±10%
0°C ~ 40°C (32~104°F)
-20°C ~ 70°C (-4~158°F)
90% RH Max, Non-Condensing
82mm x 59.5mm x 53.7mm
77g
Installation (Continue)
IV. Device Deletion
3. Delete the device from the website.
(See the features on the right side.)
4. Long press the SET button for 6 seconds.
The LED indicator blinks blue and then
turns o. After 6 seconds, the LED
indicator blinks again (faster) and then
turns o again, indicating the deletion
process is sucessful. (Please complete
the procedure in 3 minutes.)
1
2
3
Note: After device deletion, it will back to auto joining mode.
RF exposure warning statement

Federal Communications Commission (FCC) Statement
15.21
You are cautioned that changes or modifications not expressly approved by the part responsible
for compliance could void the user’s authority to operate the equipment.
15.105(b)
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1) this device may not cause harmful interference and
2) this device must accept any interference received, including interference that may cause
undesired operation of the device.
FCC RF Radiation Exposure Statement:
1. This Transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
2. This equipment complies with RF radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 20
cm between the radiator and your body.