UK Tents ECONOMY Prime 4m Series User manual

4m - series ECONOMY Prime
- 1 -
Party Tent
Please read instructions COMPLETELY before assembly. This tent MUST be securely anchored.
This tent is a temporary structure and should be disassembled at harsh weather conditions as stormy winds,
snow fall or ice.
Warnings
Prior to installation, consult with all local municipal codes regarding installation of temporary shelters. The
owner of the tent has the sole responsibility to make sure that these local rules are followed and that the
mounting is correct.
We are not responsible for damage to the unit or the contents from acts of nature.
It is always recommended that you secure your tent properly with storm straps and ground pegs when you
put up the structure. Proper Anchoring system selection is your responsibility. Heavy duty Anchor are sold
separately and are not included in this product.
Periodically check the anchors to ensure stability of shelter.
In case of extreme weather conditions, the tent cover must be removed.
Any shelter that is not anchored securely has the potential to fly away causing damage. We are not
responsible for any shelter that blows away.
This canopy is intended to protect against the effects of sun, rain, light snow, etc. It is not designed to hold
the loads that can accompany wind, rain, snow or ice storms. This structure is not tested for specific snow,
rain and wind loads.
Do not use open fire, welding equipment or other ignition sources in the tent.

4m - series ECONOMY Prime
- 2 -
Cleaning and Storage
A tight cover ensures longer life and performance. Always maintain a tight cover. Loose fabric can
accelerate deterioration of cover fabric.
Immediately remove any accumulated water, snow or ice from the roof structure.
DO NOT use bleach or harsh abrasive products to clean the fabric cover. Cover is easily cleaned with
mild soap and water.
Safety Instructions
Please use gloves and stable shoes when assembling the metal frame portion of this unit. The metal
components may have sharp edges and be oily cause of the metal processing.
Snow must be removed from the tarpaulin in a timely manner. Temporary accommodation as tents should
be taken down in adverse weather condition like heavy wind, snowfall and ice.
Ensure sufficient distance of the tarpaulin to heat sources, electrical-, gas- and other pipes (min. 1.2m). You
can obtain detailed information from your responsible authority.
Pay attention to the following points when choosing a location:
The pavilion must stand on a flat, non-slip and safe place
choose a sheltered location
Avoid damage to the material, please place the pavilion so that it cannot rub or chafe on branches, parts of
buildings etc.
Put up the pavilion at a safe distance to fireplaces and pay attention to the direction of the wind
Leave your pavilion to dry in an erected position before packing it away.
Assembly Instructions

4m - series ECONOMY Prime
- 3 -
Step1. Assembly is easiest if you layout all parts on the ground as shown below. 2 meter per section, e.g. 4x4m has
2 sections, 4x6m has 3 sections, 4x8m has 4 sections, 4x10m has 5 sections and 4x12m has 6 sections.
Assemble the roof frame by mounting parts 4 and 5 on the pipes (parts 1, 2).
Use the bolts(12) to attach the parts.

4m - series ECONOMY Prime
- 4 -
Step2.Lift one side of the tent frame and attach the legs (3). Place the roof (15) onto the frame and use the long
bungees (9) to fasten it.
Be sure not to put too much tension on the bungees in order not to make attaching the other side more difficult.
Step 3. Attach the legs on the other side. Make sure, that the leg pipes are in vertical position, to avoid overtention
on the end walls. Use the long ground pegs (7) to fasten the feet to the ground. Attach the side covers to the pipes (4)
using hooks (13).

4m - series ECONOMY Prime
- 5 -
Step 4. Unfold the side walls (16) and the end walls (17) and attach the side walls to the frame using the bungees (9).
Attach the end walls directly to the roof using the short bungees (10).
Use the short ground pegs (8) to fasten the end walls to the ground. The guy rope runs from every corner of the tent
and is braced to the ground using the spiral pegs(6).

4m - series ECONOMY Prime
- 6 -
Parts List Quantity
Item
Design
4x4m
4x6m
4x8m
4x10m
4x12m
(1) Pole 2112mm
6
8
10
12
14

4m - series ECONOMY Prime
- 7 -
(2) Pole 1930mm
6
9
12
15
18
(3) leg pole
1898mm
6
8
10
12
14
(4) Connector 4
6
6
6
6
6
(5) Connector 5
3
6
9
12
15
(6) Spiral peg
4
4
4
4
4
(7) Long peg -
6x180mm
6
8
10
12
14
(8) Short peg -
4x180mm
22
28
34
40
46
(9) Long bungee
66
84
102
120
138
(10) Short
bungee
18
18
18
18
18
(11) Guy rope 3m
4
4
4
4
4
(12) Bolt with
wing nut
30
42
54
66
78
(13) Hook
6
8
10
12
14
(14) Spanner
1
1
1
1
1
(15) Roof
1
1
1
1
1
(16) Side wall
4
6
8
10
12

4m - series ECONOMY Prime
- 8 -
(17) End wall
2
2
2
2
2