Display Function Description
ADDR
(Address)
Set DMX Address
(1-512)
Press ENTER to edit the value and use UP and DOWN to
change the value. The display will flash until the value is set
by pressing ENTER.
CHAN
(Channel)
Set DMX channel ode
(6CH/10CH)
Press ENTER to edit the channel and use UP or DOWN to
select the channel. The display will flash until the channel is
set by pressing ENTER.
AUTO Change the pre-set
FADE – Fades through colours.
CHCL – Cycles through colours.
STRO – Strobes the light.
SOUN – Light will react to sound. See
SENS for setting the sensitivity.
Press ENTER to change the pre-set.
Pre-set na e will flash until ENTER is pressed to select it.
For all pre-sets except SOUN the speed needs be set after
the pre-set has been selected. The display will show SP
followed by a 2-digit value, the higher the value the faster
the speed.
COLO
(Colour)
Manually set a solid colour
RED (0-255)
GREE (Green) (0-255)
BLUE (0-255)
UHLT (White) (0-255)
AMBE (A ber)(0-255)
PURP (Purple)(0-255)
STRO(Strobe)(0-255) 0 is no strobe.
Press ENTER and use UP or DOWN to choose which colour to
edit. Press ENTER to edit the values for each colour and use
UP or DOWN to change the value (0-255). Press ENTER to
confir the value.
Mast Slave Specify if the fixture is a aster or
slave.
MAST / SLAV
Press ENTER and then UP or DOWN to select a value. Press
ENTER to confir the selection.
SENS
(Sensitivity)
Set the sensitivity for when the light is
in the SOUN pre-set.
(0-100) 0 is least sensitive
Press ENTER and then UP or DOWN to select a value. Press
ENTER to confir the selection.
DELY
(Delay)
Set the delay fade curve. To si ulate
the fade out of tungsten light sources
0 = leds follow d x with no delay
100 = slow fade decay
Press ENTER and then UP or DOWN to select a value. Press
ENTER to confir the selection.
TEST Can be used to test each colour
RED
GREE (Green)
BLUE
UHLT (White)
YELL (Yellow)
PURP (Purple)
8.8.8.8. (All LEDS on)
Press ENTER and then UP or DOWN to select a value. It will
stay on the value selected until MENU or ENTER is pressed.
BALA
(Balance)
Sets the axi u DMX value for each
colour (0-255). Password: 240 enter
this value to access these settings.
BRED (Balance Red)
BGRE (Balance Green)
BBLU (Balance Blue)
BWHI (Balance White)
BAMB (Balance A ber)
BPUR (Balance Purple)
Press ENTER and then use UP or DOWN to enter the
password: 240 and press ENTER to confir . Then use UP or
DOWN to cycle through each colour in the list. Press ENTER
to view the current value and then press UP or DOWN to
change the value. Press ENTER to confir the new value. Use
MENU to return to the ain enu.
TEMP
(Te perature)
Displays the current te perature of
the fixture in °C
T 000-999
Press MENU to return to the previous screen.
STEM
(Set
Te perature)
Custo fan control option
OFF
ON (10-45)
Press ENTER to configure, ON or OFF will flash on the display.
Press ENTER to confir the selection, if ON was selected
then a value will flash on the display. This is the te perature
at which the fan will start running. 36°C is reco ended.
VER
(Version)
Displays the current software version.
Press ENTER to view the current software version. Press
MENU to return.
