ULTRA-LINK UL-DB3275 User manual

2.1 Hold the wall plate against your markings and place the spirit level (Hardware K) above the wall plate, adjust the wall plate until you
get an accurate level then mark your 6 screw holes with a pencil.
2.2 Use an electric drill along with a masonry drill bit. (Mark the drill bit with a piece of coloured tape to create a 50mm mark ,
this will indicate how deep your wall plate hole needs to be drilled.) Then drill with a 10mm bit into the wall (50mm) to the depth
of the coloured tape.
2.2.1 Do not drill wall plate hole into head/bed joint concrete, drill directly onto the header side of the brick.
2.3 Use a hammer to insert plastic screws (A) into the holes.
2.4 Use wallboard screw (B) and a screw driver to mount the wall plate to wall.
Position the wall plate and use the spirit level (Hardware K) to insure that the wall plate is leveled.
Parts for assembly
01
Wall plate
02
Plasma arm x 2
Hardware
B
M6x55mm Wallboard screw x6
D
M6x16mm Cross round screw x4
E
M8 x 50mm Cross round screw x4
C
M6x20mm Cross round screw x4
A
M10 Plastic screw x6
G
6 Plastic spacer x4
F
8 Plastic spacer x4
H
6 Washer x4
I
8 Washer x4
J
M5 x 25mm Cross round screw x2
K
Spirit Level x1
UL-DB3275
Fixed wall Installation
Check your TV user manual instructions to
see if there are any special requirements for
mounting your TV. If you do not understand
these instructions or have doubts about the
safety of the installation, assembly or use of
this product, contact:
INTERFOTO CC
Website: www.ultralink.co.za
Email: [email protected]
Address: 362 Roan Crescent,
Corporate Park North, Midrand
Tel: [phone]
IMPORTANT SAFETY INSTRUCTIONS
1. Unboxing the bracket:
- Using the Parts for assembly &
Hardware diagrams,
Inspect the package in order
to ensure that all the parts
have been provided.
2. Concrete wall installation:
- Determine the height
and positioning of the wall
bracket.
- Make sure that the area you
wish to mount to does not
contain any water piping
/internal cables.
- Draw a marking where you
wish to place your bracket.
50
2.2.1
K
K
A
B
Product weight : 6.2 Kg
TV size support: 32"-75"
Distance to the wall: 100mm - 440mm
Maximum load: 30kg
For Vesa Standard: 600x400
Product Features :

Hang the TV & arms on the mount.
Use cross round screw (C or D or E ), washer (H or I) and
spacer (F or G) to mount the TV set to the aluminum
siding.
3. Wood wall installation:
If you are mounting to a wood wall surface, make sure that the area you wish to mount to does not contain any water piping/internal
cables.
3.1 Use a stud detector to determine where the stud is to drill into the structure.
3.2 Determine the height and positioning of the wall bracket. Draw a marking where you wish to place your bracket.
3.3 Use an electric drill along with a 4.5mm wood drill bit (Mark the drill bit with a piece of coloured tape to the 50mm mark, this will
indicate how deep your wall plate hole needs to be drilled)
3.4 Position the wall plate and use the spirit level (Hardware K) to insure that the wall plate is leveled.
Use a screw driver & wallboard screw (Hardware B ) to screw in towards the right to tighten screws and secure the wall plate.
3.1
3.2
3.3
34
50
10
4
B
5
Disclaimer
Without Prejudice of Rights
In order to indemnify the Supplier and/ or Manufacturer please note that once this product
is purchased the Client/ Purchaser agrees to the following:
Should the product .in an unlikely event, fail to operate according to its purpose,Interfoto
CC hereby declare to repair or replace any part of the mechanism which is found to be
defective after a full investigation as to the cause. In the case of defects occurring due to
an external third party and / or the Client / Purchaser installing it incorrectly, misuse or
overloading and/ or using it for any other purpose other than that for which it was
intended, neglect or damage, external parties repairing or modifying the mechanism in any
way and or its spare parts, if the enclosed operating instructions were not followed, the
Supplier and /or Manufacturer shall not be held liable for any damage caused to the
product placed on the mechanism or wall which the mechanism is attached to or any other
property and personal injury.
Note: Proof of purchase to be produced for any claim. This product carries a ten year
warranty for manufacture faults/failures.
Hardware List:
(The below hardware is not included with the purchase of this product.)
I. 6mm spanner II. 10mm spanner III. 8mm star screw driver IV. 8mm star screw driver
V. 8mm spanner VI. 8mm star screw driver VII. 6mm star screw driver
Important: The Supplier and /or Manufacturer will not be held liable for any personal injury
or product damage due to mishandling, incorrect mounting, incorrect assembly or incorrect
use of this product.
Note: The supplied wall mounting hardware is not for use on steel stud walls or cold cinder
block walls. If you are uncertain what material your wall is constructed of or have any
questions regarding the proper installation of this wall mount, contact a qualified contractor.
If the hardware required is not included, please contact your local hardware store.
Caution:
This LCD/Plasma wall mount is intended for use on a LCD/LED/Plasma television that does not exceed the
maximum designated weight capacity. Using this mount with products heavier than the maximum weight
indicated may result in instability causing possible injury.
B
Using cross round screw(J) secure the
arms onto the bracket.